A-Neuvideo ANI-1AHC Bedienungsanleitung

ANI-1AHC

3D Mini HDMI Analyzer

HDMI Analyzer & Signal Generator 1080p and 3D Support

INSTRUCTION MANUAL

A-NeuVideo.com | Frisco, Texas 75034 | (317) 456-2461 V.1.2

SAFETY INFORMATION

1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.

Retain all documentation for future reference.

2. Follow all instructions printed on unit chassis for proper operation.

3. To reduce the risk of ﬁre, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and

excessive moisture.

5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience

receptacles, and the point where they exit from the appliance.

7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.

8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the

means of grounding of a piece of equipment is not defeated.

9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC

voltage is not covered by any warranty.

10. Turn power off and disconnect unit from AC current before making connections.

11. Never hold a power switch in the “ON” position.

12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use

the unit near stoves, heat registers, radiators, or other heat producing devices.

13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal

ﬂow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky

environment, the unit should be periodically “blown free” of foreign dust and matter.

14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to

qualiﬁed service personnel. There are no user serviceable parts inside.

15. When moving the unit, disconnect input ports ﬁrst, then remove the power cable; ﬁnally, disconnect the interconnecting cables to

other devices.

16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.

18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,

use only the original factory packing.

19. Service Information Equipment should be serviced by qualiﬁer service personnel when:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain

D. The equipment does not appear to operate normally, or exhibits a marked change in performance

E. The equipment has been dropped, or the enclosure damaged.

THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS

CONTENTS

Introduction&PackageContents..........................................1

Features & Speciﬁcations ................................................... 2

Operation Controls and Functions ..................................... 4

Front Panel ................................................................... 4

Rear Panel .................................................................... 4

Top Panel ...................................................................... 5

OSD Menu ........................................................................ 6

System Info .................................................................. 6

Sink EDID ..................................................................... 7

Source Infoframe .......................................................... 7

CEC Command ............................................................ 7

Audio Return ................................................................ 7

Deep Color Set ............................................................. 7

Exit ............................................................................... 7

OLED Display .................................................................... 8

Timing Table (Pattern Mode) ............................................. 9

Support Pattern Table ...................................................... 10

Connection Diagram ........................................................ 11

INTRODUCTION

The 3D Mini-HDMI Analyzer is a tool for checking both source (Blu-

ray or DVD players) and display devices (TV or monitors). With

touch button controls and built-in OLED (Organic Light Emitting

Diode) display it can show the status and information of both the

input and output devices connected to it by HDMI.

The analyzer can be used to analyze the input source device info-

frame and output sink device EDID. It also has a built-in pattern

generator that can be used to test the capabilities of the output

device including 3D and resolution/timing support.

PACKAGE CONTENTS

Check that you have the following components;

(1) 3D Mini-HDMI Analyzer

(1) Users Guide

(1) 5 V Power Adaptor

APPLICATIONS

• Apparatus testing

• Equipment checking

• EDID checking

• HDCP or 3D support veriﬁcation

• Production testing

• R&D design and debug

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of ﬁre,

electrical shock and injury to persons.

• To prevent ﬁre or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the

PSU if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow

for sufﬁcient space for air to circulate around the unit.

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. We assume no responsibility for any

infringements of patents or other rights of third parties which may

result from its use.

We assume no responsibility for any inaccuracies that may be

contained in this document. We make no commitment to update or

to keep current the information contained in this document.

We reserve the right to make improvements to this document and/

or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer ﬁle, in any form or by any means

— electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise — without express written permission and consent

Version 1.2 JUNE 2013

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may

be trademarks of the companies with which they are associated.

FEATURES & SPECIFICATIONS

FEATURES

• Supports Timing include SD, HD up to 1080p, PC up to WUXGA and 3D

• Provides 25 timings, 6 patterns and 1 pattern for 3D timing

• ‘Deep color’ video support (up to 12-bit, 1080p@60 Hz)

• Supports input signal bypass, digital video formats in ‘Deep Color’ Mode up to 36-bit (12-bit/color) and new lossless compressed

digital audio (Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio)

• Supports internal pattern audio LPCM 2CH 48/96/192 kHz, LPCM 5.1CH 48/96 kHz, LPCM 7.1CH 48/96 kHz

• Analyze the input source info-frame and output sink EDID information

• Touch button control function

• OLED display shows Input/Output timing information

• Supports ARC (Audio Return Channel) following HDMI v1.4 speciﬁcations

• Supports ‘Deep Color’ (8/10/12-bit) output

• Supports HDCP repeater function and complaint with HDCP

• Supports CEC bypass

SPECIFICATIONS

TMDS Clock Frequency: 225 MHz

Input Port: 1× HDMI (Female type)

Output Port: 1× HDMI (Female type)

EXT Mode (HDMI input):

• HDMI Resolution: 480i/p, 576i/p, 720p~1080p

• PC Resolution: VGA~WUXGAINT Mode (internal pattern)

• HDMI Resolution: 480i/p, 576i/p, 720p~1080p

PC Resolution: VGA~SXGA, WUXGA

3D Resolution:

• Frame Packing: 1080p@24,720p@50/60

• Side-by-Side: (Half) 1080p@24, 720p@50/60

• Top-and-Bottom: 1080p@24, 720p@50/60

AudioFormat:480i/p, 576i/p or VGA~SVGA supports LPCM 2CH 48/96/192 kHz, LPCM 5.1CH 48 kHz, LPCM 7.1CH 48 kHz, 720p~1080p

or XGA~WUXGA support LPCM 2CH, 48/96/192 kHz, LPCM 5.1CH 48/96 kHz, LPCM 7.1CH, 48/96 kHz

HDMI Cable In: 1080p/8-bit 15 m, 1080p/12-bit 10 m

HDMI Cable Out:1080p/8-bit 15 m, 1080p/12-bit 10 m

ESD Protection: Human Body model: ±8 kV (air-gap discharge) ±4 kV (contact discharge)

Power Supply: 5 V/1 A DC (US/EU standards, CE/FCC/UL certiﬁed)

Dimensions (WxDxH): 4.7 x 2.75 x 1 in

Weight: < 1lbs.

Chassis Material: Plastic

Silk Screen Color: Black

Operating Temperature: 32˚F ~ 104˚F (* 0˚C ~ 40˚C)

Storage Temperature: −4˚F ~ 140˚F (−20˚C ~ 60˚C)

Relative Humidity: 20 ~ 90 % RH (no condensation)

Power Consumption: 5W (Max)

Note: Speciﬁcations are subject to change without notice.

OPERATION CONTROLS AND FUNCTIONS

FRONT PANEL

HDMI IN: Connect the HDMI input port to the HDMI output port of the source device for testing and displaying the EDID information.

DC 5V: Plug the DC 5 V power supply into the Mini-HDMI Analyzer and connect the adaptor to an AC wall outlet.

REAR PANEL

SERVICE: Use a DB9 (RS-232) to 3.5 mm (phone jack) cable to do the software upgrade.

NOTE: This feature is not available to the end user. The DB9 to 3.5 mm phone jack is not included in the package.

ARC OPTICAL OUT: Optical digital out for testing the ARC function of a TV connected to the HDMI. Connect to the optical digital input

of an audio system (such as an AV receiver) to monitor the audio output of the attached sink device.

HDMI OUT: Connects the Analyzer to a display or to devices connected to the display when testing the capabilities of the system.

OPERATION CONTROLS AND FUNCTIONS CONTINUED

TOP PANEL

Note: Please remove the protective plastic ﬁlm from the top panel before using the touch key function.

POWER: Press this button to turn on the device, the LED will turn blue. Press again to switch the unit to standby mode, the LED will

turn red.

INT/EXT: Press this button to toggle between the built-in internal pattern generator or the external source device. The LED will

illuminate in blue when the external input is selected. To retrieve the external EDID information, an external source device must be

connected otherwise the device will only generate the test patterns to display on the TV/monitor.

PC/HD/3D: Press this button to cycle through the test patterns (PC/HD or 3D timings). The OLED display will show the timing currently

selected.

AUDIO: Press this button to select the audio sample rate from LPCM 2CH, LPCM 5.1CH and LPCM 7.1CH 48 kHz or LPCM 2CH,

LPCM 5.1CH and LPCM 7.1CH 96 kHz or LPCM 2CH and LPCM 5.1CH 192 kHz.

Note: Press and hold for 3 seconds to select Audio mute function.

M/:Press this button to enter the main menu and/or to conﬁrm the selection.

PATTERN (▲/▼): Press these keys to select the patterns or when in OSD manual press these keys to select for option.

TIMING (▲/▼): Press these keys to select the required timings.

OLED Display: Displays the relevant Information about attached devices.

OSD MENU

Press the M/button from the device to bring up the OSD on the display.

• Press pattern’s [▲/▼] to highlight on option

• Press [M/ ] to conﬁrm the selection 5.

SYSTEM INFO

Press this button to show the EDID information for any connected device. When an output display is connected, press this button

repeatedly to bring up the patterns for display (Refer to Section 10 for pattern details).

Press [M/ ] to check the input/output device information and software version.

SINK EDID, SOURCE INFOFRAME, CEC COMMAND,

AUDIO RETURN, DEEP COLOR SET & EXIT OPTIONS

SINK EDID

OPTION DESCRIPTION

Block Data To check the sink Block0 and Block1’s EDID table

Description To check the sink description of EDID

SOURCE INFOFRAME

OPTION DESCRIPTION

AVI (AVI infoframe data) To check the sink Block0 and Block1’s EDID table

AUD (Audio infoframe data) To check the sink description of EDID

CEC COMMAND

OPTION DESCRIPTION

Stand By To check the sink Block0 and Block1’s EDID table

Active Source To check the sink description of EDID

Monitor (Read) To detect the command data on the CEC Bus

Note: Source equipment must support CEC function in order to activate this function.

AUDIO RETURN

OPTION DESCRIPTION

Audio Return On/Off

DEEP COLOR SET

OPTION DESCRIPTION

8-bit On/Off

10-bit On/Off

12-bit On/Off

Note: The device will auto-detect the sink device’s ‘Deep Color’ setting and if any of the settings are not supported,

the option in the Deep Color set will not be selectable.

EXIT

Select to Exit the main menu

OLED DISPLAY

Sampling Rate: The Analyzer supports audio sampling rates of 48/96/192 kHz, display will show the signals current sample rate. If

external audio is selected the OLED will display ‘BYPASS’.

Audio Channels: The device supports audio channels from LPCM 2, 5.1 and 7.1CH. If external audio is selected the OLED will

display ‘BYPASS’.

Note: When the audio button is held down for 3 seconds, both 1 & 2 will show AUDIO MUTE.

ARC: Audio Return Channel, when this function is selected the OLED display will show ‘ARC’ if an ARC signal is present.

V Timing: Please refer to the Timing Table in Section 9 for details of the supported timing and V sync.

H Timing: Please refer to the Timing Table in Section 9 for details of the supported H Sync.

3D Format: Only when the 3D pattern is selected, the OLED display will show the pattern details.

Note: When in EXT Mode, the OLED display will show the input H/V Sync with the timing frequency and 3D pattern if any.

TIMING TABLE (PATTERN MODE)

No. RESOLUTION V Hz No. RESOLUTION V Hz

T01

T02

T03

T04

T05

T06

T07

T08

T09

T10

T11

T12

T13

480p

480i

720P

1080i

1080p

576i

576p

720p

1080i

1080p

640×480

800×600

T14

T15

T16

T17

T18

T19

T20

T21

T22

T23

T24

T25

1024×768

1280×1024

1920×1200

720p (3D Frame Packing)

720p (3D Side-by-Side)

720p (3D Top-to-Bottom)

720p (3D Frame Packing)

720p (3D Side-by-Side)

720p (3D Top-to-Bottom)

1080p (3D Frame Packing)

1080p (3D Side-by-Side)

1080p (3D Top-to-Bottom)

TIMING TABLE

TIMING TABLE (PATTERN MODE)

GROUP NO. PATTERN DESCRIPTION

Standard Type

Primary colors: Red, Green, Blue

P1: Red

P2: Green

P3: Blue

P4: Horizontal RGB Bar

P5: H Grey Scale

P6: HDCP handshaking and link-integrity

test

Inhaltsverzeichnis

Andere A-Neuvideo Messgerät Handbücher

A-Neuvideo

A-Neuvideo ANI-4KANA Bedienungsanleitung

A-Neuvideo

A-Neuvideo ANI-4KANA Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung