A.O. Smith DURA-Power DRE-52 Bedienungsanleitung

HOT WATER STORAGE DEVICES

england

MODELS DRE 52

DRE 80

DRE 120

INSTALLATION AND USER INSTRUCTIOINS

Read this manual carefully

Warning

Read this manual carefully before using the device. Not reading this manual and not

following the instructions in this manual may lead to personal injuries and damage to the

device.

Nothing from this edition may be copied, reproduced and/or made public by means of

press, photocopying or in any other way without the prior written permission of A.O. Smith

Water Products Company.

A.O. Smith Water Products Company reserves the right to change the speciﬁcations as

mentioned in this manual.

Trademarks

All brand names mentioned in this manual are registered trademarks of the respective

suppliers.

Liability

A.O. Smith Water Products Company does not accept any liability for claims of third

parties as a result of incompetent use other than mentioned in this manual and in

conformity with the General Terms and Conditions as ﬁled with the Chamber of

Commerce.

For further information see the General Terms and Conditions. These can be obtained

from us free of charge.

Although utmost care has been taken in ensuring a correct and, where necessary,

complete description of the relevant parts, the manual may contain errors and some things

may be unclear.

Should you still discover faults or things which are unclear, please inform us about this. It

helps us to further improve the documentation.

Additional information

If you have any remarks or questions concerning speciﬁc subjects related to the device,

please do not hesitate to contact:

A.O. Smith Water Products Company

P.O. Box 70

5500 AB Veldhoven

The Netherlands

Telephone: (free) 0800 - AOSMITH

0800 - 267 64 84

General: +31 40 294 25 00

Fax: +31 40 294 25 39

E-Mail: [email protected]

Website: www.aosmithinternational.com

For problems with respect to connections to electricity and water supplies, please contact

the supplier/installation engineer of your installation.

TABLE OF CONTENTS

1. GENERAL........................................................................................... 4

1.1 Device Description............................................................................................ 4

1.2 Regulation and Safety ..................................................................................... 5

1.2.1 Boil Dry Protection ............................................................................................ 7

1.2.2 Checking the Float Switch ................................................................................ 8

1.3 Technical description ........................................................................................ 9

1.4 Technical Data ................................................................................................ 10

2. FOR THE INSTALLER .....................................................................12

2.1 Installation procedures.................................................................................... 12

2.1.1 General Installation......................................................................................... 12

2.1.2 Water Connections ......................................................................................... 12

2.1.3 Electrical Connection ..................................................................................... 12

2.1.4 Electrical Diagrams......................................................................................... 13

2.2 Putting into operation...................................................................................... 17

2.2.1 Filling the Device ............................................................................................ 17

2.2.2 Putting Into Operation..................................................................................... 17

2.2.3 Putting out of Operation.................................................................................. 17

2.2.4 Temperature Regulation ................................................................................. 18

2.3 Maintenance ................................................................................................... 18

2.3.1 Sacriﬁcial anode ............................................................................................. 18

2.3.2 Descaling ........................................................................................................ 18

2.4 Steps When There is a Fault .......................................................................... 18

2.4.1 Water Temperature Not Good......................................................................... 19

2.4.2 Presumed Water Leakage .............................................................................. 19

2.4.3 Fault Table ...................................................................................................... 20

2.5 Spare Parts..................................................................................................... 20

3. FOR THE USER ...............................................................................21

3.1 Instructions for Use......................................................................................... 21

3.1.1 Filling the Device ............................................................................................ 21

3.1.2 Putting into operation...................................................................................... 21

3.1.3 Use ................................................................................................................. 21

3.1.4 Putting out of operation................................................................................... 22

3.2 Maintenance ................................................................................................... 22

3.3 Faults .............................................................................................................. 22

4. WARRANTY ..................................................................................... 23

4.1 General Warranty............................................................................................ 23

4.2 Tank Warranty................................................................................................. 23

4.3 Conditions of installation and use ................................................................... 23

4.4 Exclusions....................................................................................................... 24

4.5 Extent of the warranty..................................................................................... 24

4.6 Claims............................................................................................................. 24

4.7 No obligations for A.O. Smith other than those speciﬁed here. ...................... 24

1. GENERAL

1.1 Device Description

The structure and equipment for this

electrical heating device are in accordance

with the European standard for electrical

household devices (EN 60335-1:2002

+ A11:2004 + A1:2004 + A12:2006

+ A2:2006 en EN 60335-2-21:2003

+ A1:2005) The device thus meets

the European Directive for Electrical

Household Devices and has the right to

bear a CE mark.

The device is suitable to be used with

an operating pressure of up to 8 bar

(= 800 kPa). The tank is made of steel

plate, which has a glass lined coating

on the inside. The tank is also provided

with two sacriﬁcial anodes to give extra

protection against corrosion. A thick CFC

free polyurethane insulation layer, covered

with a steel casing, prevents unnecessary

heat loss. The device is fully ﬁlled with

water and continually starts under water

pipe pressure. When hot water is drawn off

from the device, it is immediately topped

up with cold. Incoloy heating elements are

used for good transfer of heat.

To create extra comfort in case of long

pipelines, circulating piping with a

circulating pump may be connected to

the piping. The circulating pipeline can be

connected to the cold-water supply.

Fig. 1 - regulation and safety

1.2 Regulation and Safety

For clariﬁcation see the diagram below:

(the image is an extract from the electrical

diagram further on)

3 relays (3) and a control current

transformer (5) are fed from the main

connection block (1). The main circuit

is protected by 30 Amp T fuses.

The transformer (400V to 24V) is

primarily secured with T0,2 A (4). A boil

dry protection mechanism (in the form of

a ﬂoat switch) (7) is included in the 24V

current control circuit. (The ﬂoat switch

is indicated diagrammatically. See boil

dry protection further on for more precise

explanation) The control current circuit is

closed if there is water in the device (ﬂoat

switch). In this case an auxiliary relay (6)

is used which in turn switches the relay

(3). The relays determine whether the

electrical elements are fed.

The elements are fed via the relay (3).

The wire goes to the maximum thermostat

(8) via the relays (2). The maximum

thermostat has a reset button. The output

from the maximum thermostat goes to the

regulating thermostat (9). The element

(10) is fed from the regulating thermostat.

During normal operation the regulating

thermostat (9) switches the element (10)

on and off. If a temperature of above

93°C occurs on an element the maximum

thermostat (8) locks the element. In order

to put the element back into operation the

reset button of the maximum thermostat

must be pressed in. The temperature

must have dropped by approximately

20°C before the maximum thermostat can

be reset.

If the temperature of the water above in

the tank exceeds 98°C for any reason,

the combined temperature and pressure

safety device (T&P valve) will open.

The safety control circuit will be interrupted

if the water level drops to below the ﬂoat

switch (7) or if the device is switched on

while empty.

The device is then switched off completely.

This is to prevent the elements coming

into operation while there is insufﬁcient

water present in the device (boil dry

protection).

The safety fuses, 30 Amp T for 600 V can

be ordered retrospectively from A.O. Smith.

1.2.1 Boil Dry Protection

Fig. 2 - ﬂoat switch

The boil dry protection mechanism

consists of a ﬂoat switch which monitors

the water level approximately halfway

up the tank above the elements. If there

is insufﬁcient water present in the tank,

then the ﬂoat (1) hangs down. If the tank

is ﬁlled with water then the ﬂoat is moved

upwards by the water. In the electrical

diagram the ﬂoat switch is reproduced

diagrammatically. The actual process

is as follows: the ﬂoat arm moves a

magnet with respect to the reed-contact

(2) which is located in the black plastic

tube at the end of the ﬂoat switch. The

movement of the magnet changes the

magnetic ﬁeld and the reed-contact is

closed.

The exposure height (3) of the reed

contact is very important.

This is 14 mm. This setting may not

be changed!

Explanation:

With an exposure height of 14 mm the

switch point is approximately halfway

along the stroke of the ﬂoat.

If the exposure height is set lower, then

the switch point shifts upwards. If the

exposure height is too small the contact

will no longer connect even if the ﬂoat

is completely above it. In this case the

device will not come into operation.

If the exposure height is set lower than

14 mm , then the switch point shifts

downwards. This means that the contact

will already connect upon a small

upwards movement of the ﬂoat. If the

exposure height is set too high then the

contact is permanently closed and the

safety mechanism does not work. This

means that the elements can come into

operation without there being sufﬁcient

water present in the device. This will lead

to the elements burning out in a very

short time and short circuit and leakage.

So never change the exposure height.

The reed contact and the ﬂoat must

always be vertical. The arrow on the

clamping plate on the front must point

upwards. The ﬂoat switch is secured in

the tank with nut (5). By loosening nut

(4) the ﬂoat switch can be set vertically.

Nut (4)

is sealed with an o-ring with respect to

nut (5). The ﬂoat switch must be taken

out of the device as a complete unit

for checking or replacement. (The ﬂoat

cannot be passed through the opening in

nut (5).) For this purpose the device thus

has to be drained.

1.2.2 Checking the Float Switch

Switch off the feed voltage and remove

the fuses from the elements. In this

way the control circuit can be tested

without the elements being put into

operation. Drain the device until the

water is deﬁnitely below the ﬂoat switch.

If desired the ﬂoat switch can now be

removed for visual inspection. Check

the resistance of the contacts with a

multimeter and check whether the switch

point is situated approximately halfway

along the stroke of the ﬂoat. (For new

contacts this resistance is between 1

and 1.5 Ohms). Screw the ﬂoat switch

back into the tank and place it vertically.

Check the exposure height. Close the

door and connect the feed voltage. The

safety relays must not come in. (The

tautening and release of the safety

relays is clearly audible.) Now allow

water to ﬂow into the device. If the water

presses the ﬂoat upwards, the ﬂoat

switch closes the control circuit and the

safety relays will tauten. Then drain the

device once again. The lowering of the

water level will lead to the ﬂoat switch

blocking the control circuit once again

and the safety relays will release. Repeat

this operation at least one time.

Switch off the feed voltage and ﬁt the

fuses of the elements again. Close the

door and reconnect the feed voltage.

1.3 Technical description

Fig. 3 - Measurements

Measurement Description 52 80 120

AHeight hot water connection 1460 1580 1600

BHeight of upper side of device 1420 1540 1570

DDiameter of boiler 560 640 750

EDepth 690 790 910

MHeight of drain valve 125 125 125

RHeight cold water supply 125 125 125

SHeight T&P connection 1230 1335 1380

1Cold water connection 1¼”-14NPT 1¼”-14NPT 1¼”-14NPT

2Hot water connection 1¼”-14NPT 1¼”-14NPT 1¼”-14NPT

3T&P connection ¾”-14NPT ¾”-14NPT ¾”-14NPT

4Drain plug connection ¾”-14NPT ¾”-14NPT ¾”-14NPT

All measurements are in mm (rounded up to 5mm).

1.4 Technical Data

Type DRE 52-9 DRE 52-18 DRE 52-36

Tank capacity litres 200 200 200

Number of elements - 3 3 6

Power 380V-3F kW 7.6 15.2 30.3

Power 400V-3F kW 8.4 16.8 33.6

Power 414V-3F kW 9.0 18.0 36.0

Heating time up to 60*

(400/414V) min 83/78 42/39 21/19

Heating time up to 40*

(400/414V) min 50/47 25/23 12/12

Tap capacity 1st hour 60°C**

(400/414V) litres 329/339 467/486 741/781

Tap capacity continuous 60°C**

(400/414V) litres/hour 145/155 289/310 578/619

Tap capacity 1st hour 40°C**

litres 549/565 778/810 1235/1300

Tap capacity continuous 40°C

litres/hour 241/258 482/516 963/1032

Weight kg 73 73 73

Type DRE 80-9 DRE 80-18 DRE 80-36 DRE 80-54

Tank capacity litres 300 300 300 300

Number of elements - 3 3 6 9

Power 380V-3F kW 7.6 15.2 30.3 45.5

Power 400V-3F kW 8.4 16.8 33.6 50.4

Power 414V-3F kW 9.0 18.0 36.0 54.0

Heating time up to 60*

(400/414V) min 125/116 62/58 31/29 21/19

Heating time up to 40*

(400/414V) min 75/70 37/35 19/17 12/12

Tap capacity 1st hour 60°C**

(400/414V) litres 425/435 563/582 837/876 1112/1170

Tap capacity continuous 60°C**

(400/414V) litres/hour 145/155 289/310 578/619 867/929

Tap capacity 1st hour 40°C**

litres 709/725 938/970 1395/1460 1853/1951

Tap capacity continuous 40°C

litres/hour 241/258 482/516 963/1032 1445/1548

Weight kg 110 110 110 110

Andere Handbücher für DURA-Power DRE-52

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere A.O. Smith Boiler Handbücher

A.O. Smith

A.O. Smith FPST Anleitung zur Verwendung

A.O. Smith

A.O. Smith 315795-000 MH Bedienungsanleitung

A.O. Smith

A.O. Smith IT - 1000 Bedienungsanleitung

A.O. Smith

A.O. Smith ***81-140 Installations- und Benutzerhandbuch

A.O. Smith

A.O. Smith HIGH EFFICIENCY ATMOSPHERIC VENTGAS WATER... Bedienungsanleitung

A.O. Smith

A.O. Smith BTX-80 Bedienungsanleitung

A.O. Smith

A.O. Smith Master-Fit 100 Series Anleitung zur Verwendung

A.O. Smith

A.O. Smith 110 Bedienungsanleitung

A.O. Smith

A.O. Smith ProMax GCNH30100 Bedienungsanleitung

A.O. Smith

A.O. Smith 101 Series Bedienungsanleitung

A.O. Smith

A.O. Smith CEWHR-PE6 Bedienungsanleitung

A.O. Smith

A.O. Smith EWS-10 Bedienungsanleitung

A.O. Smith

A.O. Smith CEWHR 35 Bedienungsanleitung

A.O. Smith

A.O. Smith GDVH-40 Bedienungsanleitung

A.O. Smith

A.O. Smith CYCLONE XHE BTH 300A Bedienungsanleitung

A.O. Smith

A.O. Smith Residential Gas Water Heaters Bedienungsanleitung

A.O. Smith

A.O. Smith 186589-004 Bedienungsanleitung

A.O. Smith

A.O. Smith 300 Series Bedienungsanleitung

A.O. Smith

A.O. Smith TC-049-R2 Anleitung zur Verwendung

A.O. Smith

A.O. Smith IT - 300 Fehlerbehebungshandbuch

A.O. Smith

A.O. Smith BTR 120 Betriebsanleitung

A.O. Smith

A.O. Smith COF-199 Benutzerhandbuch

A.O. Smith

A.O. Smith Innovo 12-160 Installations- und Benutzerhandbuch

A.O. Smith

A.O. Smith HSE-SBS-015 Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung