A.O. Smith HSE-SES-015 Bedienungsanleitung

Size: 210mm (H) x 148mm (W)

Part No.: 327621-000_R0

Fit it &

Forget it

Why people prefer an A. O. Smith water heater...

* Conditions Apply User Guide

Water Heater

HSE-SES-015 / HSE-SES-025

Blue Diamond glass lined

tank. Maximum protection

against hard water and

corrosion.

Get the best quality that

ensures, you have a water

heater that works in

Indian water conditions.

Guaranteed* A. O. Smith

Service within 24 hours.

Call: 1.800.103.2468

Made in India’s most

modern and advanced

water heater factory.

ADVANCED

TECHNOLOGY

SUPERIOR QUALITY EXPERT SERVICE

One of the most energy

efficient water heater you

can buy.

ENERGY SAVING

Wireless remote controller,

digital clock, temperature

settings, power ON/OFF,

energy meter.

MORE FEATURES &

USER CONTROLS

MADE BETTER

Congratulations!

And welcome to the A. O. Smith family.

We would like to thank you for the trust you have shown in choosing an A. O. Smith water

heater. You can be sure it will live up to your expectations. Thousands of delighted users all over

the world trust A. O. Smith water heaters for their families. This user guide will introduce you

to your water heater. Follow the instructions carefully and look forward to enjoying long years

of trouble-free service.

A. O. Smith is a company known for its innovative technologies and energy-efficient solutions.

Ours are the only water heaters with the Blue Diamond Glass lining for the inner container of

the water heater. This cutting edge technology prevents sediment and scaling, fights corrosion

and extends the life of your water heater. We also offer you an exciting range of colour options

for the front panel of your water heater. Choose the one that matches your bathroom décor

best.

Our customer-centric approach manifests itself in many other ways too. If you need any

information or assistance with your water heater, just call us from any phone, anywhere in the

country to our Toll Free Customer Care No. 1.800.103.2468.

Factory Address:

A. O. Smith India Water Heating Private Limited

Plot No. 300, Phase-2, KIADB Industrial Area, Harohalli, Kanakapura Taluk,

Ramanagara District - 562 112, Karnataka, India.

About A. O. Smith

A. O. Smith India Water Heating Private Limited was established in 2006. Since then, the

A. O. Smith team has conducted numerous focus group studies and spent endless research

hours determining what India wanted in a water heater. Backed by 75 years of proven

technological advances, A. O. Smith India has created a stylish design with features demanded

by the Indian consumer.

The A. O. Smith plant with manufacturing facilities spread over 76,000 sq.ft. is located on

20 acres, just outside Bengaluru, in the KIADB Industrial Area, Harohalli. The India operations

is the 16 A. O. Smith manufacturing facility worldwide. A. O. Smith's India plant has extensive

engineering and technical resources and has the latest technologies incorporated. A. O. Smith

is the first manufacturer to invest in and produce glass lined water heaters in India.

Today, A. O. Smith Corporation is one of the largest water heater manufacturers in the world

and is a global leader in innovative technology and energy efficient solutions.

What's in the box?

Contents

Specifications ..........................................................................................1

Key Features ............................................................................................2

Installation...............................................................................................3

Directions for use ....................................................................................7

A. O. Smith ColourMatch System .......................................................10

Changing the Decorative Front Panel ..................................................10

Troubleshooting ....................................................................................11

Circuit Diagram .....................................................................................11

Warranty ................................................................................................12

Jurisdiction ............................................................................................13

Warranty Card .......................................................................................14

Service and Maintenance......................................................................15

Remote Accessories

& Battery

Electric Water Heater with

Wireless Remote Controller

Mounting

Accessories

User Guide

Discharge Tube

Fit it &

orget it

Why people prefer an A. O. Smith water heater...

* Conditions Apply User Guide

Water Heater

HSE-SES-015 / HSE-SES-025

Blue Diamond glass lined

tank. Maximum protection

against hard water and

corrosion.

Get the best quality that

ensures you have a water

heater that works in

Indian water conditions.

Guaranteed* A. O. Smith

Service within 24 hours.

Call: 1.800.103.2468

Made in India’s most

modern and advanced

water heater factory.

ADVANCED

TECHNOLOGY

SUPERIOR QUALITY EXPERT SERVICE

One of the most energy

efficient water heater you

can buy.

ENERGY SAVING

Wireless remote controller,

digital clock, temperature

settings, power ON/OFF

energy meter.

MORE FEATURES &

USER CONTROLS

MADE BETTER

Specifications

Model HSE-SES-015 HSE-SES-025

Volume [L] 15 25

Power [W] 2000 2000

Voltage/Frequency [V/Hz] ~230/50 ~230/50

Actual Stdg. Loss [kWh/24h/45°C diff.] 0.510 0.620

Max. Stdg. Loss [kWh/24h/45°C diff.]

[as per IS 2082:1993 amended in 2002] 1.138 1.386

Reheating Time for 35°C rise [in min.] 18 29

Temperature range [°C] 25-75 25-75

Rated water pressure N/cm 80 80

Water head (metres) 80 80

Inlet/Outlet connections [Inch] ½ ½

Dimensions

Caution: *Safety valve has been factory fit with the water heater and set at 0.8 MPa

(8 Bar) rated pressure.

Warning: Do not tamper or detach the safety valve from the water heater.

1 Outlet

2 Inlet

3 Safety Valve*

4 Digital Control

5 Decorative Front Panel

6 Front Jacket

7 Back Jacket

8 Anode

9 Heating Element

10 Tank

11 Installation Bracket

12 PU Insulation

13 Thermal Cutout

Part Descriptors

Model HSE-SES HSE-SES

-015 -025

A [mm] 373 444

B1 [mm] 373 444

B2 [mm] 405 483

C [mm] 337 371

B2 B1

Key Features

Blue Diamond Glass Lining

Anode Rod

Safety Valve

Thermal Cutout

Note: A. O. Smith reserves the right to amend or modify the specifications and features at

any time, as and when required without any prior notification.

Blue Diamond technology increases the life of the inner tank. The lining is

stronger and more corrosion resistant than any other in the industry.

The safety valve is designed to automatically relieve and discharge water, in case

the pressure overshoots the preset limits.

If the water temperature exceeds the highest preset level, the breaker rapidly

cuts off the live line and the neutral line simultaneously to assure safety.

The tank has an anode rod which has stainless steel core that is designed to

protect the tank from corrosive elements. The anode rod uses a special cathodic

action to fight these elements and thus prolong the life of the water heater.

Digital Control & Wireless Remote Controller

Displays the temperature and the total energy consumed by the water heater.

Temperature can be precisely set between 25°C to 75°C. It is easy to operate the

water heater with wireless remote controller.

Glass Coated Heating Element

Scale and sediment build-up on the surface of the element can lead to

premature failure. A. O. Smith Glass Coating helps to prevent scale formation

and extends the life of the heating element.

Installation

Mounting

Fig. 1 Position for installation Fig. 2 Wall mounting bracket

1. Make sure that the wall can withstand at least twice the weight of the water heater when

completely filled with water.

2. Before locating the position for installation of the water heater, make sure that there is

sufficient clearance between the ceiling and the side wall. (Fig. 1)

3. Use a drill bit with diameter of 10mm to drill 4 holes at least 90mm deep in the wall (Fig. 3).

The four holes should be aligned horizontally and vertically. The horizontal distance between

the 2 holes should be 120mm and the vertical distance should be 57mm. (Fig. 2)

4. Insert the expansion anchors into the holes. Place the wall mounting bracket over the

expansion anchors and tighten the screws on the bracket. (Fig. 3)

5. Place the water heater on wall mounting bracket (Fig. 4) using hanger hooks. Tug

downwards on the heater to ensure that the water heater is fixed steadily.

Wall

Fig. 3 Installation of wall mounting

bracket

Fig. 4 Inserting the water heater

into mounting bracket

Wall Water

Heater

Water

Heater

Wall

Water

Heater

Wall

*Flexible Hoses to be procured by the customer, not part of standard product.

Fig. 5 Installation diagram

Hot Water Tap

Cold Water Tap

Discharge Tube

*Flexible Hose

Lever

To Drain

Safety Valve

Blue Cap

Red Cap

Water heater

Ceiling Wall

1. Open a hot water faucet nearby to permit the air to escape.

2. Open the cold water inlet valve fully, filling the heater and the piping.

3. Close the hot water faucet when water flows.

4. Check all the connections to see if there is any leakage. In case of a leakage, drain the

heater completely, repair the leaking joint and then refill the heater.

Electrical Connections

The power cord and plug are connected with this water heater. Find a separate socket for

power plug and make sure the socket is in firm contact with the plug. Ensure that reliable

earthing has been done.

Caution:

• Connect the water heater using independent sockets, do not use adapters. Use

multimeter to check whether the live line and neutral line are not reverse, to ensure

complete safety.

• Before installing the water heater, confirm that the power of water heater matches

electric meter capacity and supply wire.

• The water heater should be earthed reliably. It is prohibited to connect the earth wire

to neutral wire or tap water pipe.

Attention:

• Make sure a suitable sealing tape is used for all connections to prevent leakage.

• Discharge tube should be installed downwards without any loops, folds or knots.

Ensure that the free end of the Discharge tube is placed over a suitable drain and away

from the users.

• Discharge tube is provided to release the discharge from the water heater(through the

safety valve) in case excessive pressure is developed. The contents of the discharge

from the Safety valve may be hot and may cause burns to the users and damage

nearby objects if not properly routed to a drain.

• It is recommended to operate the discharge lever in the safety valve on a regular basis

to ensure that there are no blockages and also to remove any lime deposits that would

have been formed inside the water heater.

• Ensure that the water heater is in power OFF condition when the Discharge lever is

being operated. Ensure that the water is filled completely in the water heater before

switching it ON.

Water Filling

Plumbing

1. Make necessary plumbing with reference to the installation diagram. (Fig. 5)

2. A. O. Smith recommends nylon/SS braided hoses having a minimum pressure rating of

8 Bar and hoses should be compatible for hot water applications.

3. Connect the cold water pipe to the inlet [Blue Cap].

4. Connect the hot water pipe to the outlet [Red Cap].

5. Attach the discharge tube to safety valve as shown in installation diagram. (Fig. 5 & 6)

For draining water from the water heater, following steps

needs to be followed:

1. Switch off the electric supply to the water heater.

2. Open the hot water taps until the water is not hot any

more.

3. Close cold water supply.

4. Drain the water by moving the lever of safety valve in the

direction of the arrow as indicated in the diagram. (Fig. 6)

Draining

Fig. 6 Safety valve

Discharge Tube

Safety Valve

Port

Fixing the wireless remote controller bracket

For convenience of operation, please install the wireless

remote controller holder/bracket on the wall near the water

heater (a bracket may be used).

Fixing the bracket for wireless remote controller:

• The wireless remote controller must be installed at a

place where it does not get in direct contact with

water.

• Drill two holes on the wall by using an electric impact

drill with 6mm bit.

• The holes must be horizontal and space between two

holes is 28mm (Fig. 7).

• Fix the bracket on the wall by expansion tubes and

screws attached.

• Place the wireless remote controller with battery into

the bracket.

Insertion of the wireless remote controller battery:

• Rotate counter clockwise by a coin and remove the battery cover at the back of the

wireless remote controller.

• Load the CR2025 battery (accessory) into the controller.

Note: “+” up.

• Cover the battery cover and rotate it clockwise by a coin (Fig. 8).

Fig. 7 Bracket for wireless

remote controller

28mm

Caution:

• Before using the water heater, make sure that it should be completely filled with water.

• Please turn off the power supply to the water heater prior to draining the water heater.

Warning: This water heater should not be operated with insufficient amount of water.

Failure to do so may result in damage to the water heater & injuries to the users. This

will also make the warranty null & void.

Fig. 8 Insertion diagram of wireless remote controller battery

Caution:

• Once the mounting, plumbing, discharge tube, power connection and water filling

is completed, then only the power supply should be given.

• During repair or periodic maintenance, if necessary, the power cord or Internal

electrical wiring should be replaced by A. O. Smith Authorised service personnel only.

• It is not permitted for the power supply plug and cord to be replaced or altered by

unauthorised people or by the users themselves. This will make the warranty null and

void and may cause the water heater operation hazardous.

Battery Size:

CR2025 3V

407888-016

Rotate after

pressing

Open/close

by a coin

Open

Battery Size:

CR2025 3V

407888-016

Rotate after

pressing

Open/close

by a coin

Open

Battery Size:

CR2025 3V

407888-016

Open

Rotate after

pressing

Open/close

by a coin

Battery Size:

CR2025 3V

407888-016

Open

CR2025

Directions for use

Caution: Before using the water heater, make sure the inner tank is completely filled with

water and the power plug has been connected properly.

It is recommended that the wireless remote controller should be fixed on the

remote bracket (Fig. 8). Ensure that the wireless remote controller box does not

get in direct contact with water. Do not use wet hands while operating the

wireless remote controller.

1. Initial power

When the water heater power supply plug is connected, it is in

initial power on state, i.e. the heater is ready for heating the

water. The digital control will perform the diagnosis function

and all indicators will glow and goes off as shown in Fig. 10.

2. Power ON/OFF

To start heating the water, press ON/OFF key “ ” on digital

control or wireless remote controller. While heating, the

display shows actual temperature of water inside the tank and

the indicator glows as shown in Fig. 11.

3. Clock setting

The clock is Real Time Clock. Press “Set Clock” key on wireless

remote controller to display the time. Press for the second

time to set hour time (first two digits) starts blinking. Adjust

the hour time by pressing ““ or ““ keys and again press

“Set Clock” key to set the minutes time (last two digits) starts

blinking. Adjust the minute time by pressing ““ or ““ keys

and press “Set Clock” key to set the minute time. Now the

clock time is set as shown in Fig. 12.

Fig. 10

Fig. 11

Fig. 12

Fig. 9 Digital Control

Temperature

Decrease

LED Indicators

ON / OFF

Temperature

Increase

Display LED

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere A.O. Smith Boiler Handbücher

A.O. Smith

A.O. Smith XCRX-50-LP Produktinformationsblatt

A.O. Smith

A.O. Smith BT180-100 Bedienungsanleitung

A.O. Smith

A.O. Smith SGE Bedienungsanleitung

A.O. Smith

A.O. Smith APW015DW Beilage

A.O. Smith

A.O. Smith SGS - 100 Beilage

A.O. Smith

A.O. Smith 120 through 250 Series Anleitung zur Verwendung

A.O. Smith

A.O. Smith T-H3J-DV Bedienungsanleitung

A.O. Smith

A.O. Smith CAWH 8-455-6 Fehlerbehebungshandbuch

A.O. Smith

A.O. Smith CYCLONE Xi BTH 500A Bedienungsanleitung

A.O. Smith

A.O. Smith EQ 115 Bedienungsanleitung

A.O. Smith

A.O. Smith POWER VENT GAS Bedienungsanleitung

A.O. Smith

A.O. Smith DURA-Power DVE-120 Bedienungsanleitung

A.O. Smith

A.O. Smith EES - 30 Montageanleitung

A.O. Smith

A.O. Smith 104 Series Bedienungsanleitung

A.O. Smith

A.O. Smith FDV Bedienungsanleitung

A.O. Smith

A.O. Smith BTI 100 G Leitfaden

A.O. Smith

A.O. Smith 200 Series Bedienungsanleitung

A.O. Smith

A.O. Smith GDVH Bedienungsanleitung

A.O. Smith

A.O. Smith ELECTRIC WATER HEATER Bedienungsanleitung

A.O. Smith

A.O. Smith SAS Bedienungsanleitung

A.O. Smith

A.O. Smith ProMax+plus High Efficiency SERIES 100 Bedienungsanleitung

A.O. Smith

A.O. Smith Voltex series Produktinformationsblatt

A.O. Smith

A.O. Smith DSE-5 THRU DSE-120 Bedienungsanleitung

A.O. Smith

A.O. Smith HSE-SBS-015 Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung