ABB SPA-ZC 400 Bedienungsanleitung
Ethernet Adapter
Product Guide
SPA-ZC 400
3
Ethernet Adapter SPA-ZC 400
Features • IEC 61850 connectivity for REF 541/3/5
REM 543/5 and RET 541/3/5
• Easy-to-use configuration tool for
IEC 61850 data mapping
• IEC 61850 horizontal communication
(GOOSE)
• Disturbance recorder file upload via
IEC 61850
• Simultaneous dual port communication
for LON®and SPA (Optional)
• Communication over SPA/TCP
• Communication over Modbus/TCP
REF 542plus
COM600
Application
a060239
Fig. 1 Conceptual picture of a typical system setup
Introduction
SPA-ZC 400 enables connection of one
REF 541/3/5, REM 543/5 or RET 541/3/5
device to the IEC 61850-8-1 Station bus.
IEC 61850 is the new standard for substation
communication. Additionally to being a com-
munication standard, it also supports general
substation automation functions as well as the
engineering process.
The GOOSE messaging of the IEC 61850
standard is used in substation automation for
fast horizontal communication between Intel-
ligent Electronic Devices (IED) to send, for
example, interlocking and blocking informa-
tion.
SPA-ZC 400 also enables ethernet access to
an IED using the SPA over TCP/IP and Mod-
bus over TCP/IP.
In addition to the IEC 61850-8 communication
the
SPA-ZC 400 optionally enables
simulta-
neous dual port communication for fibre-optic
SPA and LON
®
.
More information on how to physically con-
nect the device can be found in the chapter 5
of the Installation and Commissioning man-
ual. SPA-ZC 400 programming is described
in the Installation and commissioning man-
ual, chapter 6, Engineering.
As a prerequisite, you should understand the
communication properties of the IED that is
to be connected to Ethernet adapter. This
information is available in the manual for the
protection IED in question.
1MRS755450
Issued: 08.11.2004
Status: Updated
Version:D/20.05.2009
Data subject to change without notice
Ethernet Adapter SPA-ZC 400
1MRS755450
4
Design Module parts
1. Ethernet connector
2. LON/SPA bus FO connector (optional)
3. LON/SPA Rx LED
4. LON/LAN service pin
5. LAN and diagnostic LEDs
A040138b
Fig. 2 Parts of SPA-ZC 400
Technical data Interfaces
SPA-ZC 400 - IED interface
Fixed mechanics and fixed connectors for
REF 541/543/545, REM 543/545 and
RET 541/543/545
• D-type subminiature connector for
IEC 61850 traffic
• D-type subminiature connector for simul-
taneous dual port communication.
IEC 61850 interface
LAN connectors
• RJ-45 (STP CAT5e) galvanic connection
• MT-RJ multimode glass fibre transceiver
• LC multimode glass fibre transceiver
LON/SPA interface (Optional)
Fibre optic connector options
• ST multimode glass fibre transmit-
ter/receiver pair or
• Snap-in multimode plastic fibre transmit-
ter/receiver pair
Optical fibres
See fibre optic quides:
• SPA-ZF Optical glass fibres, multimode
graded index type specifications,
1MRS755371
• Plastic-core fibre optic cables, features and
instructions for mounting,
1MRS752089-MUM
Diagnostic leds
SPA-ZC 400 common diagnostic LEDs:
- Power
- Diagnostic:
-Red
- Green
LAN diagnostic LEDs:
- LINK
- TX
- RX
LON/SPA diagnostic LED:
- RX
43
195
IP
00-0C-02-B0-CC-00
50
20.4
26
SPA-ZC 400
ETHERNET ADAPTER
POWER
LINK
TX
RX
DIAG
LAN
SERVICE
PIN
ETHERNET
RX TX
PLASTIC GLASS
IEC 61850
MODBUS TCP
SPA TCP
Ethernet Adapter SPA-ZC 400
1MRS755450
Technical data (cont´d)
5
SPA-ZC400 dimensions and weight
A040130b
Fig. 3 SPA-ZC 400 dimensions
Type Dimensions [mm] Weight [g]
SPA-ZC 400 195 x 50 x 26 130
Tests and conditions
Environmental tests and conditions
Recommended service temperature range -10...+55°C (continuous)
Transport and storage temperature range -40...+85°C according to the IEC 60068-2-48
Dry heat test IEC 60068-2-2
Dry cold test IEC 60068-2-1
Damp heat test IEC 60068-2-30
Electromagnetic compatibility tests
EMC immunity test level meets the requirements listed below
1 MHz burst disturbance test, class III
Common mode
Differential mode
According to the IEC 60255-22-1
2.5 kV
1.0 kV
Electrostatic discharge test, class IV
For contact discharge
For air discharge
According to the IEC 6100-4-2 and
IEC 60255-22-2
6 kV
8 kV
Radio frequency interference tests
Conducted, common mode
Radiated, amplitude-modulated
Radiated, pulse-modulated
According to the IEC 61000-4-6 and
IEC 60255-22-6
10 V (rms), f = 150 kHz ... 80 MHz
According to the IEC 61000-4-3 and
IEC 60255-22-3
10 V/m (rms), f = 80 ... 2700 MHz
According to the ENV 50204 and
IEC 60255-22-3
10 V/m, f = 900 MHz
Fast transient disturbance tests
All terminals
According to the IEC 60255-22-4 and
IEC 61000-4-4
4 kV
Surge immunity test
Power supply
According to the IEC 60255-22-5 and IEC 61000-4-5
4 kV, line-to-earth
2 kV, line-to-line
Power frequency (50 Hz) magnetic field According to the IEC 61000-4-8
300 A/m continuous
Electromagnetic emission tests
Conducted, RF-emission (Mains term.)
Radiated RF-emission
According to the EN 55011
EN 55011, class A, IEC 60255-25
EN 55011, class A, IEC 60255-25
CE compliance Complies with the EMC directive 2004/108/EC and the LV
directive 2006/95/EC
Standard tests
Mechanical tests
Vibration tests (sinusoidal)
Shock and bumb test
According to the IEC 60255-21-1, class I
According to the IEC 60255-21-2, class I
Supply current consumption
Running 340 mA
Start up 430 mA
Ethernet Adapter SPA-ZC 400
1MRS755450
Technical data (cont´d)
6
RoHS Compliance
Complies with the RoHS directive 2002/95/EC
SPA-ZC400MMG
Ethernet connector type
M MTRJ
L LC
R RJ-45
Protocol type
M Modbus/TCP
E IEC 61850
S SPA/TCP
Device type
Optical transmitter and receiver for SPA/LON bus
P plastic fibre cable
G glass fibre cable
- no fibre option
Ethernet Adapter SPA-ZC 400
1MRS755450
7
Ordering
A060158
Fig. 4 Ordering information for SPA-ZC400
SPA-ZC 400CD
• SPA-ZC 400 Configuration CD:
- Communication Engineering Tool
(CET) for SPA-ZC40x
- Connectivity packages for
REF 541/543/545, REM 543/545 and
RET 541/543/545.
Order at least one SPA-ZC 400 configu-
ration CD with your delivery to get the Com-
munication Engineering Tool for SPA-ZC40x
and the Connectivity Packages. SPA-ZC 400
packages do not include the configuration CD
by default.
References Related documents
Name of the document Document id
SPA-ZC 400 Installation and commissioning manual 1MRS755347
SPA-ZC 400 configuration CD 1MRS151048
CAP 505 User’s Guide 1MRS752292-MUM
SPA-ZF Optical glass fibres, multimode graded index
type specifications
1MRS755371
Plastic-core fibre optic cables, features and
instructions for mounting
1MRS752089
Standard IEC 61850, parts -6, -7-2, -7-3, -7-4, -8-1
ABB Oy
Distribution Automation
P.O. Box 699
FI-65101 Vaasa, FINLAND
Tel +358 10 22 11
Fax +358 10 224 1094
www.abb.com/substationautomation
Andere Handbücher für SPA-ZC 400
3
Inhaltsverzeichnis
Andere ABB Adapter Handbücher
ABB
ABB CEM 05100 Bedienungsanleitung
ABB
ABB CCA-01 Bedienungsanleitung
ABB
ABB FieldKey NHU200 Bedienungsanleitung
ABB
ABB FSCA-01 Bedienungsanleitung
ABB
ABB Tina 2B Bedienungsanleitung
ABB
ABB SPA-ZC 402 Bedienungsanleitung
ABB
ABB RETA-01 Bedienungsanleitung
ABB
ABB Busch-AudioWorld Busch-iDock 8218 U-500 Bedienungsanleitung
ABB
ABB FEPL-02 Ethernet POWERLINK Bedienungsanleitung
ABB
ABB FDNA-01 Bedienungsanleitung
ABB
ABB FBIP-21 BACnet/IP Installationshandbuch
ABB
ABB SPA-ZC 400 Leitfaden
ABB
ABB Tina 7A Bedienungsanleitung
ABB
ABB AC 31 Montage- und Bedienungsanleitung
ABB
ABB SPA-ZC 400 Leitfaden
ABB
ABB FPBA-01 PROFIBUS DP Installationshandbuch
ABB
ABB SPA-ZC 400 Leitfaden
ABB
ABB FEA-01 F Series Bedienungsanleitung
ABB
ABB Unifix AD 1STQ003941B0000 Handbuch
ABB
ABB SPA-ZC 402 Leitfaden
