ABB SPACOM 300 Bedienungsanleitung
—
Relay Retrofit Program
Cutting Tool
Operating Guide SPACOM 300
RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300 3
—
1. Preparations
Remove the existing relay.
Ensure that there is enough space to operate
the cutting tool in all intended directions.
Check the space required by the replacement
IED and its wiring.
Place the cover plate in its intended location.
Mark the outline for the opening and the fixing screw
locations in each corner of the cover plate.
Drill the holes for fixing screws using a drill bit
of 4.5 mm in diameter.
1.1
1.2
—
2. Cutting cycle
Horizontal: 1, 4, 3 and 2.
Min. 171
214
139
4RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300
—
3. Operating the cutting tool on a horizontal edge
Ensure that the cutting head is set in the correct
position. The text HORIZONTAL Up and Down must
point in the direction you are cutting.
Make four punches, side by side.
Ensure that you use the correct guiding,
before each cutting cycle.
After each cutting cycle, ensure that thecutting head
is clear of offcut!
3.1
3.2
3.3
RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300 5
Push the vent lever to release the punch
after each cutting cycle.
For your safety, keep your hands on the power unit,
never on the cutting head.
Beware of the sharp edges!
Note the cutting order. Cut the parts next to
the edges first and the middle part last.
3.4
3.5
3.6
6RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300
—
5. Finishing your work
Finish your work and install the new IED.
Clean the offcuts from the floors.
5.1
—
4. Install the cover plate
Close the door and install the cover plate.
Use the self-tapping screws supplied with
the cover plate.
4.1
7
—
Notes
1MRS757999 REV C EN 3-2019
© Copyright 2019 ABB. All rights reserved.
Specifications subject to change without notice.
Additional information
We reserve the right to make technical changes or
modify the contents of this document without prior
notice. With regard to purchase orders, the agreed
particulars shall prevail. ABB does not accept any
responsibility whatsoever for potential errors or
possible lack of information in this document.
We reserve all rights in this document and in the
subject matter and illustrations contained therein.
Any reproduction, disclosure to third parties or
utilization of its contents – in whole or in parts – is
forbidden without prior written consent of ABB.
—
For more information, please contact
E-Mail: af[email protected]
abb.com/service
abb.com/mediumvoltage
Inhaltsverzeichnis
Andere ABB Relais Handbücher
ABB
ABB Relion 615 series Bedienungsanleitung
ABB
ABB Relion 615 series Bedienungsanleitung
ABB
ABB CWC Handbuch
ABB
ABB CA-16 Bedienungsanleitung
ABB
ABB CO Bedienungsanleitung
ABB
ABB CA-16 Handbuch
ABB
ABB EF19 Bedienungsanleitung
ABB
ABB KLF Handbuch
ABB
ABB REU 610 Produkthandbuch
ABB
ABB REJ 525 Bedienungsanleitung
ABB
ABB MG-6 Handbuch
ABB
ABB COV Series Handbuch
ABB
ABB RELION REX640 Bedienungsanleitung
ABB
ABB RED615 ANSI Bedienungsanleitung
ABB
ABB SGR-51 Bedienungsanleitung
ABB
ABB KLF-1 Handbuch
ABB
ABB CW Series Handbuch
ABB
ABB System pro M RLI Bedienungsanleitung
ABB
ABB SSR32 Bedienungsanleitung
ABB
ABB RELION 650 SERIES Bedienungsanleitung
