ACME ArtDMX A28 Bedienungsanleitung

CA-EN28

ArtDMX A28

User Guide

Please read these instructions carefully before use

2016.12.15

毅丰

受控正本

CONTENTS

1. Features...................................................................................................................2

2. General Instructions...............................................................................................3

3. Overview..................................................................................................................4

3.1 Front View.....................................................................................................4

3.2 Rear View......................................................................................................4

4. Operation Guide.....................................................................................................5

4.1 Startup View..................................................................................................5

4.2 Main menu..................................................................................................6

4.2.1 Rename Device...................................................................................7

4.2.2 Set IP Address.....................................................................................7

4.2.3 Set Netmask.........................................................................................7

4.2.4 Set DMX port .......................................................................................8

4.2.5 Set ID NO...........................................................................................10

4.2.6 Set LCD Backlight.............................................................................10

4.2.7Set LED Brightness............................................................................11

4.2.8 User Preset........................................................................................11

4.2.9 Version................................................................................................12

5.Application Diagram.............................................................................................13

1. Features

RJ45 Ethernet (LAN) connector, 10/100/1000M self-adaption, support

TCP/IP protocol

Ethernet connector supports Auto MDI/MDIX

Support standard DMX-512 and ArtNet protocol

Support ArtNet←→DMX signal bilateral conversion

DMX input/output can be set as able/disabled

Each DMX output can be set as single, zero, HTP, LTP，RDM mode

Can be acted as DMX splitter

IP address can be set manually

Six kinds of user pre-setting

Display indicates each DMX port status

LED indicators indicate the activate status of Ethernet

Online updates software

2 DMX input, 8 DMX output. All the input /output with optoelectronic

isolation

NOTE: Some basic knowledge of DMX is required to fully utilize this unit.

2. General Instructions

Please read the user manual carefully, as it includes important information

regarding details of operation, maintenance, and technical data. Keep this

manual with the unit for future consultation.

WARNINGS！

♦DO NOT make any inflammable liquids, water or metal objects enter the

unit.

♦Should any liquid be spilled on the unit, DISCONNECT the power

immediately.

♦STOP using the unit immediately in the event of serious operation

problems and contact with your local dealer for a check or contact us

directly.

♦DO NOT open the unit--there are no user serviceable parts inside.

♦NEVER try to repair the unit by yourself. Repairs by unqualified people

could cause damage or faulty operation.

CAUTIONS！

♦After having removed the packaging, please check that the unit is NOT

damaged in any way. If in doubt, DON'T use it and contact an authorized

dealer.

♦Packaging material (plastic bags, polystyrene foam, nails, etc.) MUST

NOT be left within children's reach, as it can be dangerous.

♦This unit must only be operated by adults. DO NOT allow children to

tamper or play with it.

♦NEVER use the unit under the following conditions:

In places subject to excessive humidity.

In places subject to vibrations or bumps.

In places with a temperature of over 45℃/113 F or less than 2℃/35.6 F.

Protect the unit from excessive dryness or humidity (ideal conditions are

between35% and 80%).

♦DO NOT dismantle or modify the unit privately.

3. Overview

3.1 Front View

1 POWER LED indicator

To show the on/off status of the unit

2 LINK LED indicator

Network connect status indicate

3 ACTIVITY LED indicator

Network activity indicator, when there is

any data transmit, it will flash.

4 LCD Display

display the present status and the

available option

5 MENU Button

6 UP/DOWN Button

7 ENTER Button

Enter into main menu or back to last

UP and DOWN

Enter and Confirm

8 Power Switch Button

Power ON/OFF the unit

3.2 Rear View

9 Power supply

Connect with the power cord

10 Ethernet RJ45 connector

Connect with network cable

11 DMX In port A B

DMX in

12 DMX port 1-8 Can be set as DMX in/DMX out

4. Operation Guide

4.1 Startup View

There are 4 different statuses (as pictures show) you can check when you

power on the unit. You can switchover them by pressing the UP and DOWN. All

of the options can be changed in the main menu.

In the port status, A/B means the network port; “x” means there is no network

connected. “√” means the network has been connected. 1-8 refers to the DMX

port 1-8. In the status, “x” means the DMX port’s status is inactive. It will hold

the current output. “√” stands the DMX port’s status is activity, it has connected

to the network. “-” means the current port status is forbidden.

4.2 Main menu

4.2.1 Rename Device

Enter into the main menu by press MENU, then pressing the UP and DOWN

to choose the Rename Deviceoption and then press the ENTER to confirm

your selection. Now you can rename the device by pressing UP and DOWN

now. Confirm you change and move to next option by press the MENU.

4.2.2 Set IP Address

Enter into the main menu by press MENU, then pressing the UP and DOWN

to choose the Set IP Address option and then press the ENTER to confirm

your selection. Now you can set IP address by pressing UP and DOWN now.

Confirm you change by press the ENTER.

Please note: Each of the IP address should be unique.

4.2.3 Set Netmask

Enter into the main menu by press MENU, then pressing the UP and DOWN

to choose theSet Netmaskoption and then press the ENTER to confirm your

selection. Now you can set Netmaskby pressing UP and DOWN now.

Confirm you change by press the ENTER.

4.2.4 Set DMX port

Enter into the main menu by press MENU, then pressing the UP and DOWN to

choose the Set DMX port option and then press the ENTER to confirm your

selection. Then you can set the parameter of the each port by pressing UP

/DOWN and ENTER now.

1) DMX Input A B

Press ENTER button and select DMX IN Port A or DMX IN Port B. Then

press the button UP and DOWN to set the Port Status and Povtuniverse

from 001 to 256.

2) 1-8 DMX Input

You can enter to any of the DMX port 1-8 and set as below:

1, Port Status, DMX port status can be set as IN / OUT/ DIS;

2, As the DMX port set as Input status, then the Mode only can be set as

normal or backup.

3, Framerte/fs, adjust the speed of DMX output

4, Principal, adjust the value

5, Secondary, adjust the value

6, Resend, adjust or disable the value for universal of network

7, Display Mode, adjust the display mode

Normal mode means it will send the data received from DMX IN port to the

universal of network regardless if there is any data in the universal of the

network.

Backup mode refers that when there is any data on the universal of

network, the CA-AN08 won’t send any data to universal of network. Only

when the universal of network is no any data, then the CA-AN08 will

receive the data from DMX IN port and send it to the universal of network

simultaneously.

3) 1-8 DMX output

Any of the port 1-8 also can be set as Output or Disabled status. Upon the port

has been set as Output status, there are LTP, HTP, Zero, Single and RDM

these 5 modes can be selected.

Zero means the port output should be “0’;

Single means this port will only output one universal.

LTP means this port will output the latter one between the universal of principle

and secondly. The unit will compare the two universal and resend the later one

to the network.

HTP means the port will output the one with higher value between the

universal of principle and secondly. The unit will compare the two universal and

resend the higher data to the network. They can be set within the range of

0.0-F.F./001-255. (These two formats can be change through Display Mode)

RDM means the port output can support Remote Device Manager.

4) 1-8 DMX port disabled

Inhaltsverzeichnis

Andere ACME Verstärker Handbücher

ACME

ACME TrussHub U Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung