ACME TrussHub U Bedienungsanleitung

CA-AN04T

CONTENTS

1. Safety Instructions..............................................................................................2

2. Features...................................................................................................................4

3. Overview..................................................................................................................5

3.1 Front/ Rear View..........................................................................................5

4. Operation Guide.....................................................................................................6

4.1 Startup View..................................................................................................6

4.2 Main menu..................................................................................................7

4.2.1 Rename Device...................................................................................7

4.2.2 Set IP Address.....................................................................................8

4.2.3 Set Netmask.........................................................................................8

4.2.4 Set DMX port .......................................................................................8

4.2.5 Set ID NO...........................................................................................12

4.2.6 Set LCD Backlight.............................................................................12

4.2.7 User Preset........................................................................................12

4.2.8 Version................................................................................................14

5.Application Diagram.............................................................................................15

1. Safety Instructions

WARNING

Please keep this User Manual for future consultation. If you sell the fixture to another user, be

sure that they also receive this instruction booklet.

Please unpack and check carefully there is no transportation damage before using the fixture.

Please disconnect main power before servicing and maintenance.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

The ambient temperature is Ta: 0℃-40℃. DO NOT operate it where above or below the range

of temperature.

DO NOT connect the device to any dimmer pack.

The housing must be replaced if they are visibly damaged.

Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

There are no user serviceable parts inside the fixture. Do not open the housing or attempt any

repairs by yourself. In the unlikely event your fixture may require service, please contact your

nearest dealer.

In the event of serious operating problem, stop using the fixture immediately. Never try to

repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or

Please read the instruction carefully which includes important

information about the installation, usage and maintenance.

malfunction. Please contact the nearest authorized technical assistance center. Always use the

same type spare parts.

Installation:

The unit is fully operational in three different mounting positions, hanging upside-down from a

ceiling or set on a flat level surface. To avoid internal damage to the unit, never mount the unit

on its side as illustrated above. Be sure this fixture is kept at least 0.5m away from any

flammable materials (decoration etc.). Always use and install the supplied safety cable as a

safety measure to prevent accidental damage and/or injury in the event the clamp fails.

2. Features

RJ45 Ethernet (LAN) connector, 10/100M self-adaption, support TCP/IP

protocol

Support standard DMX/RDM and ArtNet protocol

Support ArtNet←→DMX/RDM signal bilateral conversion

DMX input/output can be set as able/disabled

Each DMX output can be set as single, zero, HTP, LTP，RDM mode

Each DMX input can be set as normal / backup mode

Can be acted as DMX/RDM splitter

IP address can be set manually

OLED display indicates each DMX port status

Online updates software

4 DMX output. All the input /output with optoelectronic isolation

Input is electrically isolated from output and output to withstand voltage：

＞2000V

NOTE: Some basic knowledge of DMX is required to fully utilize this unit.

3. Overview

3.1 Front/ Rear View

1. Button:

To enter into move backward or

leave the menu

To go backward to move up in the

DOWN

To go to move down in the menu

ENTER

To perform the desired functions

2. OLED Display:

Display the present status and the available option.

3. LED indicator:

To show the power/signal status of the unit.

4. Ethernet RJ45 connector:

Connect with network cable

5. D MX port 1-4:

Connect with network cable.

6. Power In:

To connect to the mains supply

4. Operation Guide

4.1 Startup View

There are 5 different status (as pictures show) you can check when you power

on your unit. You can switchover them by pressing the UP and DOWN. The

first four options can be changed in the main menu.

In the port status, A/B refers to the DMX port Ethernet IN/ Ethernet Thru;

1/2/3/4 refers to the DMX port 1/2/3/4; In the first line,√/x means the port

status is activity/inactive; “-” means the current port status is disabled. In the

second line, “-” means the current port status is input signal.

When the screen is in the fifth state, Hold the ENTER key for 3 seconds and

enter the MAC address modification interface,You can set their values by

pressing the UP and DOWN, confirm you change by press the ENTER.

4.2 Main menu

4.2.1 Rename Device

Enter into the main menu by press MENU, then pressing the UP and DOWN

to choose the Rename Device option and then press the ENTER to confirm

your selection. Now you can rename the device by pressing UP and DOWN

now. Confirm you change and move to next option by press the MENU.

4.2.2 Set IP Address

Enter into the main menu by press MENU, then pressing the UP and DOWN

to choose the Set IP Address option and then press the ENTER to confirm

your selection. Now you can set IP address by pressing UP and DOWN now.

Confirm you change by press the ENTER.

Please note: Each of the IP address should be unique.

4.2.3 Set Netmask

Enter into the main menu by press MENU, then pressing the UP and DOWN

to choose the Netmaskoption and then press the ENTER to confirm your

selection. Now you can set Netmaskby pressing UP and DOWN now.

Confirm you change by press the ENTER.

4.2.4 Set DMX port

Enter into the main menu by press MENU, then pressing the UP and DOWN to

choose the set DMX port option and then press the ENTER to confirm your

selection. Then you can set the parameter of the each port by pressing UP

/DOWN and ENTER now.

1) 1-4 DMX Input

You can enter to any of the DMX port 1-4 and set as below:

1, Port Status, DMX port status can be set as IN / OUT/ DIS;

2, As the DMX port set as Input status, then the Mode only can be set as

normal or backup.

3, Framerte/fs

4，NET

5，Principal

6，Secondary

7, Resend

8,Display Mode Dec

Normal mode means it will send the data received from DMX IN port to the

universal of network regardless if there is any data in the universal of the

network.

Backup mode refers that when there is any data on the universal of

network, the CA-AN04T won’t send any data to universal of network. Only

when the universal of network is no any data, then the CA-AN04T will

receive the data from DMX IN port and send it to the universal of network

simultaneously.

2) 1-4 DMX output

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME Verstärker Handbücher

ACME

ACME ArtDMX A28 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung