ActionTec 802CAG Bedienungsanleitung

Page: 1

Actiontec

802.11a/g Dual Band

CardBus Adapter

802CAG

User Manual

Page: 2

1. Content

1. Contents

2. Introduction

3. Installation Overview

4. Regulatory Compliance Information

Page: 3

2. Instruction

Device Description

The 802CAG is the Wireless cardbus adapter to support IEEE 802.11a, 802.11b & 802.11g

standard. The design is based on Atheros AR5001X+ Combo WLAN chip set: AR5111 5GHz

radio, AR2111 2.4GHz radio, and AR5212 802.11a/b/g MAC + Baseband.

Features

- Atheros AR5001X+ Combo WLAN chip set

- Support IEEE 802.11a, 802.11b & 802.11g standards

- Full hardware support for Advanced Encryption Standard (AES) security at full line-speed

with no performance degradation. Support for Key Integrity Protocol (TKIP) and WEP

- Support Ad hoc, and Infrastructure both network architectures

- Quality of Service support (QoS) for real time video, audio voice

- Up to 108-Mbps Atheros Turbo Mode in addition to standard rates of 6, 9, 12, 18, 24, 48

and 54-Mbps

- Dynamic Frequency Selection (DFS) and Transmit. Power Control (TPC) for international

use

- Extended 5.150 to 5.850-GHz and 2.400 to 2.500-GHz tuning ranges

- Enhanced performance, transmission range and reliability

- Onboard diversity antenna

Specification Compliance

- IEEE 802.11a

- IEEE 802.11b

- IEEE 802.11g

- PCI Bus Interface Spec. 2.2

- PC Card Standard Spec. 7.1

Form factor

- Extended Type II PCCard

Page: 4

3. Installation Overview

Actiontec recommends that you remove any existing Atheros drivers on the PC system before

installing Version 1.0 release of the NDIS driver.

With on existing Actiontec NDIS driver installed, insert the Actiontec Wireless Network

Adapter into a 32-bit CardBus slot, and follow these steps to install the NDIS driver:

1. Wait for the dialog box to appear. Choose “Found New Hardware Wizard,” and click

Next to continue

2. Under “Search for the best driver in these locations,” choose “Include this location in

the search” and click Browse to find the location of the NDIS driver. When the driver

location has been identified, click Next to continue.

3. The Actiontec driver currently does not have a digital signature from Microsoft.

Therefore, Windows XP shows a warning message. Click Continue Anyway to

proceed with driver installation.

4. Click Finish to complete driver installation, and refer to “Device Configuration” on

page 4-7 for device configuration.

Windows XP Wireless Network Configuration

Windows XP provides zero-configuration functionality that automatically tries to connect the

STA to available wireless networks in the following order:

• Infrastructure mode with valid WEP keys

• Infrastructure mode with unauthenticated access for stations without WEP keys

• Ad hoc mode

To configure wireless network settings through the Windows XP user interface:

1. Open Network Connections from Control Panel

2. Right-click the Local Area Network Connection icon (pertinent to Actiontec Wireless

Network Adapter).

3. Click Enable to enable the device first, and then click Properties.

4. On the Wireless Networks tab, select the “Use Windows to configure my wireless

network settings” check box to enable automatic wireless network configuration.

Note that you can disable automatic wireless network configuration, and revert back to

using Atheros NCP configuration settings, by clearing the “Use Windows to configure my

wireless network settings” check box.

Page: 5

Infrastructure Mode

To set up automatic wireless network configuration to connect to an existing Access

Point (infrastructure network), follow these steps:

1. Click the network name under “Available networks” in the Wireless Networks tab,

and click Configure. You can update the list of available networks that are within

range of your computer by clicking Refresh under Available Networks.

2. If the network requires WEP, then the “Data encryption (WEP enabled)” check

box is selected by default in Wireless Network Properties.

3. Select “The key is provided for me automatically” check box if the WEP key is

automatically provided for you. The driver will then use the Default Encryption

key from the current Atheros NCP configuration profile irrespective of the

network name.

You may choose to enter the WEP key by clearing this check box and manually

entering the network key and key length.

Ad Hoc Mode

To connect to an existing computer-to-computer (ad hoc) network:

1. Click the ad hoc network name under “Available networks” in the Wireless

Networks tab, and click Configure.

2. In Wireless Network Properties, the “This is a computer-to-computer (ad hoc)

network; wireless access points are not used “check box is selected by default.

You may choose to enable WEP by selecting the “Data encryption (WEP

enabled)” check box and the “Network Authentication (Shared mode)” check box.

3. Select the “The key is provided for me automatically” check box if the shared key

is automatically provided for you. The driver will then use the Default Encryption

key from the current Atheros NCP configuration profile irrespective of the

network name.

You may choose to enter the shared key by clearing this box and enter the key and

key length manually.

4. If you want to connect to an ad hoc network, but both ad hoc and infrastructure

networks are within range of your computer, then click Advanced in the Wireless

Networks tab and then select “Computer-to-computer (ad hoc) networks only.

Note that if you want the station to start its own ad hoc network, the “Computer-

to-computer (ad hoc) networks only” option should be selected. There should be

no network active from the preferred list and the “Automatically connect to non-

preferred networks” check box should be cleared.

Page: 6

Connect to an Available Wireless Network

When there is more than one available network detected by Windows XP, the OS will

prompt you to select and connect to a preferred network.

To connect to an available wireless network, right-click the network connection icon

in the notification area, and then click “View Available Wireless Networks”.

In Connect to Wireless Network, under “available networks”, select the wireless

network that you want to connect to. If a network key is required and is automatically

provided for you, then leave “network key” blank. If the network key is not

automatically provided for you, then type the key in “Network key”. Click Connect to

establish the network connection.

If you are either unable to make a connection to the wireless network that you selected

or need to configure additional wireless network connection settings, click Advanced

in Connect to Wireless Network, and the Wireless Networks tab will appear.

You can configure a new wireless network connection by clicking Add, and specifying

the network name (SSID) in Wireless Network Properties, and the wireless network

key settings, if needed.

If the network connection that you are configuring is an ad hoc network, then select

“This is a computer-to-computer (ad hoc) network; wireless access points are not

used” check box. The network will be added under “Preferred networks” in the

Wireless Networks tab.

You can change the order of the preferred networks by selecting the wireless network

that you want to reposition on the list, and then clicking Move up or Move down.

You can change the wireless network connection setting s of a preferred network by

selecting the wireless network, clicking Properties, and then changing the settings as

needed.

To remove a wireless network from the list of preferred networks, select the wireless

network that you want to remove, and then click Remove.

If a network is not defined in the preferred networks list, but you know it is available

and you want t automatically connect to it, then click Advanced in the Wireless

Networks tab, and select the “Automatically connect to non-preferred networks” check

box.

Page: 7

4. Regulatory Compliance Information

Radio Frequency Interference Requirements

This device is restricted to indoor use due to its operations in the 5/15 to 5/25 GHz

frequency range. FCC requires this product to be used indoors for the frequency range

5/15 to 5/25 GHz to reduce the potential for harmful interference to co-channel Mobile

Satellite systems.

High power radars are allocated as primary users of the 5/25 to 5/35 GHz and 5.65 to

5.85 GHz bands. These radar stations can cause interference with and/or damage this

device.

Declaration of Conformity

We, Actiontec Electronics, Inc.

760 North Mary Ave., Sunnyvale, CA 94086 USA

declare under our sole responsibility that the product 802CAG – 802.11a/b/g Dual

Band CardBus Adapter complies with Part 15 of FCC rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that my

cause undesired operation.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, with can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following methods:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Page: 8

Modifications made to the product, unless expressly approved by Actiontec

Electronics, Inc. could void the user’s authority to operate the equipment.

RF Exposure

This device has been tested for compliance with FCC RF Exposure (SAR) limited in

typical laptop configurations.

In order to comply with SAR limits established in the ANSI C95.1 standards, it is

recommended when using a PC card adapter that the integrated antenna is positioned

more than 2.5 cm from your body or nearby persons during extended periods of

operation. If the antenna is positioned less than 2.5cm from the user, it is

recommended that the user limit exposure time.

European Community Notice

• Marking by the symbol indicates compliance with the Essential

Requirements of the R&TTE Directive of the European Union (1999/5/EC). This

equipment meets the following conformance standards:

EN 301 893, EN 301 489-17, ETS 300 328-2, EN 60950

• This device should not be operated in the following European Community countries

using the 5GHz bands: Greece and Spain. The radio spectrum authorities in these

countries do not currently allow operation in the 5GHz bands.

• Operation of this device in the 5GHz bands in the U.K. currently requires the end

user or installer to contact the U.K. Radiocommunications Agency (phone: 0207 211

0181) to request a Temporary Use License for 5GHz operation. The Temporary

Use License requirement will be removed once pending U.K. license exemption

legislation is finalized.

• This device is restricted to indoor use when operated in the European Community

using channels in the 5150-5350 MHz band to reduce the potential for harmful

interference to other users of the band.

• To remain in conformance with European National spectrum usage laws, the

following channel limitations apply per the table below. The user should use the

utility provided with the product software to check the current channel of

operation. If operation is occurring outside of the allowable frequencies as listed in

the table, the user should cease operating the product and consult with the local

technical support staff responsible for the wireless network.

• This device is restricted from operating in ad-hoc mode using channels in the 5GHz

bands in the European Community. Ad-hoc mode is direct communication

between two client devices without an Access Point.

Page: 9

Allowable Frequencies of Operation Countries

5150-5250 MHz

(Channels 36, 40, 44, 48)

Austria, Germany, Liechtenstein, Switzerland

5150-5350 MHz

(Channels 36, 40,44,48,

52,56,60,64)

Belgium, France, Ireland, U.K. (temporary

license required for operation in U.K.)

5150-5350 & 5470-5725 MHz

(Channels 36, 40, 44, 48, 52, 56,

60, 64, 100, 104, 108, 112, 116,

120, 124, 128, 132, 136, 140)

Denmark, Finland, Iceland, Italy,

Luxembourg, Netherlands, Norway, Portugal,

Sweden

2446.5Mhz - 2483.5Mhz

(Channels 10,11,12,13)

France

For questions regarding your product, please contact:

Actiontec Electronics, Inc

760 North Mary Ave,

Sunnyvale, CA 94086

United States

Phone 408-752-7700

Fax 408-732-0087

Email www.actiontec.com

Inhaltsverzeichnis

Andere ActionTec Adapter Handbücher

ActionTec

ActionTec 802UIG Bedienungsanleitung

ActionTec

ActionTec ECB7250 KIT Bedienungsanleitung

ActionTec

ActionTec MegaPlug HPE 200AVP Bedienungsanleitung

ActionTec

ActionTec 54 Mbps Wireless Multiport Print Server Bedienungsanleitung

ActionTec

ActionTec SBWD100KIT Bedienungsanleitung

ActionTec

ActionTec USB Wireless Bluetooth Adapter Bedienungsanleitung

ActionTec

ActionTec HWU05470 Bedienungsanleitung

ActionTec

ActionTec MegaPlug AV HPE200AV Bedienungsanleitung

ActionTec

ActionTec HWE05490-01 Bedienungsanleitung

ActionTec

ActionTec MegaPlug AV Bedienungsanleitung

ActionTec

ActionTec ECB2200 Bedienungsanleitung

ActionTec

ActionTec 802URM Bedienungsanleitung

ActionTec

ActionTec SBWD100KIT Bedienungsanleitung

ActionTec

ActionTec 14 Mbps HomePlug Ethernet Adapter Bedienungsanleitung

ActionTec

ActionTec 802URG Bedienungsanleitung

ActionTec

ActionTec BTM200 Bedienungsanleitung

ActionTec

ActionTec 14 Mbps HomePlug Ethernet Adapter Bedienungsanleitung

ActionTec

ActionTec MegaBoost C802URG Bedienungsanleitung

ActionTec

ActionTec 802UIG-1 Bedienungsanleitung

ActionTec

ActionTec 802AIN Bedienungsanleitung

ActionTec

ActionTec 802EAG Bedienungsanleitung

ActionTec

ActionTec USB Wireless Adapter 802UI3(b) Bedienungsanleitung

ActionTec

ActionTec 11 Mbps Wireless Access Point Bedienungsanleitung

ActionTec

ActionTec MegaPlug HPE100T Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung