ACU-RITE 00899 Bedienungsanleitung

ACU•RITE.

Self Empty ng

Instruction Manual

Rain Gauge

model 00899

CONTENTS

Unpacking Instructions ............. 2

Package Contents .................... 2

Product Registration ................. 2

Features & Benets: Rain Gauge ... 3

Features & Benets: Display ........ 4

Setup ...................................... 5

Rain Gauge Setup.................... 5

Display Setup .......................... 6

Set Time, Date & Units.............. 7

Placement Guidelines ............... 7

Rain Gauge Installation ............ 8

Using the Rain Gauge .............. 9

Programmable Rain Alarm...... 10

Troubleshooting ......................11

Calibration ............................ 12

Care & Maintenance.............. 13

Specications......................... 13

FCC Information .................... 13

Customer Support .................. 14

Warranty............................... 14

Questions? Contact Customer Support at

(877) 221-1252 or visit www.AcuRite.com

SAVE THIS MANUAL FOR FUTURE REFERENCE.

Congratulations on your new AcuRite product. To ensure the best

possible product performance, please read this manual in its entirety

and retain it for future reference.

Unpacking Instructions

Remove the protective lm that is applied to the LCD screen prior to using this

product. Locate the tab and peel off to remove. Remove packing materials

from inside of the rain gauge.

Package Contents

1. Display

2. Rain Gauge

3. Instruction Manual

PRODUCT MUST BE REGISTERED

IMPORTANT TO RECEIVE WARRANTY SERVICE

PRODUCT REGISTRATION

www.AcuRite.com

Features & Benets

3. Battery Compartment &

Electronics Box

4. Rain Gauge Base

5. A-B-C Switch

RAIN GAUGE

1. Rain Gauge Cover

2. Rain Gauge Tipping Cups

Collects and empties rain for

continuous rain measurement.

A B C

SQUEEZE

ID code that must match display’s A-B-C

switch to ensure units synchronize.

ODAY 5 - MF & OAT

Features & Benets

4567 8

DISPLAY

1. MODE Button

Toggle between rainfall readings

for EVENT, 1 DAY, WEEK, TOTAL

A or TOTAL B.

2 . CLEAR Button

Clears data being viewed for

current mode (#1).

3. HIST Button

Displays historical data.

4. FLOOD WATCH ALARM Indicator

Indicates conditions are present

that could lead to ooding.

5. RAIN ALARM Indicator

Indicates that a rain event has

begun.

6. Display Low Battery Indicator

7. HISTORY Icon

Indicates historical data is being

viewed.

8. Clock

9. Date

10. SET Button

For setup preferences.

11. + Button

For setup preferences.

12. Rain Gauge Signal Strength

13. RAIN ALARM Button

Activates/Deactivates rain alarm.

14. Rain Gauge Low Battery Indicator

15. FLOOD WATCH Button

Activates/deactivates ood watch alarm.

16. Rainfall Total

For current mode selected (#1).

17. Mode

Indicates mode displayed (#1).

• •

•

SETUP

Rain Gauge Setup

Install or Replace Batteries

AcuRite recommends high quality alkaline batteries for the best product

performance. Heavy duty or rechargeable batteries are not recommended.

SQUEEZE

2 SQUEEZE

LARGE SQUEEZE

TAB LARGE

TAB

SQUEEZE TABS TO OPEN

3 4

1. Separate rain gauge cover from the base by gently

squeezing tabs and pulling the cover upwards.

2. Remove battery box by squeezing the two tabs on

each end together.

3. Remove and discard cardboard rain gauge stabilizer.

4. Insert 2 x AA batteries into the battery compartment

as shown. Follow the polarity (+/-) diagram in the

battery compartment.

5. Securely place the battery box back into the rain

gauge base.

6. Securely re-attach the rain gauge cover onto rain

gauge base.

Set the A-B-C Switch

Locate the A-B-C switch inside the

battery compartment. Set the A-B-C

switch to A, B or C. You must select

the same letter choices for both the

rain gauge and the display in order

for the units to synchronize.

A-B-C Switch

Set to match

display

A B C

• •

•

Display Setup

Set the A-B-C Switch

Locate the A-B-C switch inside the

battery compartment. Set the A-B-C

switch to A, B or C. You must select

the same letter choices for both

the display and the rain gauge in

order for the units to synchronize.

Install or Replace Batteries

1. Remove the battery

compartment cover.

2. Insert 3 x AA alkaline batteries

into the battery compartment,

as shown. Follow the polarity

(+/–) diagram in the battery

compartment.

3. Replace the battery cover.

A-B-C Switch

Set to match

rain gauge

PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE

WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.

BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be

A B C 2 Install Batteries

3 AA batteries

used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used

batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in ﬁre,

as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge

non-rechargeable batteries. DO NOT short-circuit the supply terminals.

Set the Time, Date & Units

This rain gauge is equipped with historical data and alarms that require accurate

time and date settings to function properly. It is important to set the time, date and

units before using the rain gauge.

Press and hold the “SET” button for 3 seconds to enter SET MODE. Once in set

mode, the preference you are currently setting will blink on the display.

To adjust the currently selected (ashing) item, press and release the “+” or “-”

button (press and HOLD to fast adjust).

To save your adjustments, press and release the “SET” button again to adjust the

next preference. The preference set order is as follows:

CLOCK HOUR (note AM/PM indicators)

CLOCK MINUTE

CALENDAR MONTH

CALENDAR DATE

CALENDAR YEAR

UNITS (INCH or MM)

You will automatically exit SET MODE if no buttons are pressed for 20 seconds. Enter

SET MODE at any time by pressing and holding the “SET” button for 3 seconds.

Placement for Maximum Accuracy

AcuRite sensors are sensitive to surrounding environmental conditions. Proper

placement of both the display and rain gauge are critical to the accuracy and

performance of this product.

Display Placement

Place the display in a dry area free of dirt and dust.

Display stands upright for tabletop use or is wall-mountable.

Important Placement Guidelines

•Display and rain gauge must be within 100 ft (30 m) of each other.

•To maximize wireless range and communication, install the rain gauge at

least 3 ft (.9 m) above ground. Place both the display and the rain gauge

away from large metallic items, thick walls, metal surfaces, or other objects

that may limit wireless communication.

•To prevent wireless interference, place both units at least 3 ft (0.9 m) away

from electronic devices (TV, computer, microwave, radio, etc.)

TV 3

LEAST

APART

100 feet maximum

(30 meters)

Rain Gauge Installation

• To ensure accurate rain measurement, the rain gauge MUST be

placed on a at, level surface.

• Ensure the rain gauge is not placed in a low spot that could become

ooded or in an area where there are obstructions above it.

1. Separate the rain gauge cover from the rain gauge base.

2. Locate the two holes on the rain gauge base.

3. Fasten the rain gauge base to a sturdy surface, like a deck railing or a fence

post, with screws (included) using hand tools. (Power tools may slip during

installation, causing damage to the rain gauge.)

INSTALL 2 SCREWS USING

HAND TOOLS ONLY.

THEN RE-ATTACH UPPER CASING

SQUEEZE

SQUEEZE TABS TO OPEN

Setup is Complete

The rain gauge will now synchronize with the display. It may take afew minutes

for synchronization to complete. Please refer to the troubleshooting section of this

manual if anything appears to be functioning improperly.

OPERATION

Using the Rain Gauge

Modes & Historical Data

Press the MODE button to view rainfall data for different modes. While a mode

is being viewed, press the CLEAR button to erase the reading being viewed or

press the HIST button to view historical readings. You will automatically exit

HIST mode if no buttons are pressed for 30 seconds. Enter HIST mode at any

time by pressing the HIST button.

EVENT Mode

When EVENT mode is selected, rainfall data is shown for the most recent

rainfall. An event ends when no rainfall has been detected for 8 hours. An

event may be a brief drizzle, or a multi-day storm.

To display the last 7 rain event rainfall totals, press the HIST button. Each time

the HIST button is pressed, one rain event is displayed with the event’s time

and date. To clear an event from memory, press AND HOLD the CLEAR button

while the event is being viewed. Clearing data from EVENT mode does not

impact other modes.

1 DAY Mode

When 1 DAY mode is selected, rainfall data is shown for today.

To display the DAILY RAIN for the last 7 days, press the HIST button. Each time

the HIST button is pressed, the total rainfall recorded for the day will be shown

with the time rainfall started (if applicable) and date. To clear any DAY rainfall

total from memory, press AND HOLD the CLEAR button while the data for the

day is being viewed. Clearing a day’s rainfall data will subtract that rainfall

amount from the WEEK, TOTAL A and TOTAL B modes.

WEEK Mode

When WEEK mode is selected, rainfall data is shown for the past calendar

week (Sunday through Saturday).

To display the WEEKLY RAIN for the last 7 weeks, press the HIST button. Each

time the HIST button is pressed, the total rainfall recorded for the week will

be shown with the time rainfall started (if applicable) and date. To clear any

WEEK rainfall total from memory, press AND HOLD the CLEAR button while

the data for the week is being viewed. Clearing a week’s rainfall data will

subtract that rainfall amount from TOTAL A and TOTAL B modes.

TOTAL A/B Mode

TOTAL A and TOTAL B are total rainfall measured since the rain gauge was

powered on or since the last time the mode was cleared. To display the start

time and date for TOTAL A or TOTAL B, press the HIST button. To clear

TOTAL A or TOTAL B mode, press AND HOLD the CLEAR button while the

mode is being viewed.

Alarms

Flood Watch Alarm

Press the FLOOD WATCH button to activate or deactivate the FLOOD WATCH

ALARM. When the alarm is ON and ood and saturation conditions are

present, an alarm will sound and the FLOOD WATCH indicator will highlight on

the display. Flood conditions include:

> 3” (76.2 mm) in the last 7 days, and then >0.7” (17.78 mm) in the last 2 hours or

>1” (25.4 mm) in the last 24 hours

> 2.3” (58.4 mm) in the last 4 days, and then >0.7” (17.78 mm) in the last 2 hours or

>1” (25.4 mm) in the last 24 hours

> 1.5” (38.1 mm) in the last 2 days, and then >0.7” (17.78 mm) in the last 2 hours or

>1” (25.4 mm) in the last 24 hours

> 1.4” (35.6 mm) in the last 2 hours

> 1.6” (40.6 mm) in the last 8 hours

> 1.8” (45.7 mm) in the last 24 hours

If ood or saturation conditions occur, the alarm sounds for 1 minute or until

any button is pressed. If no buttons are pressed, the FLOOD WATCH indicator

will ash on the display, and the alarm will sound three times on the hour for

the next 8 hours.

NOTE: The rain gauge measures rainfall even while the ood alarm is off.

Rain Alarm

Press the RAIN ALARM button to activate or deactivate the RAIN ALARM.

When the alarm is ON and any rainfall is detected an alarm will sound and

the RAIN ALARM indicator will highlight on the display. The alarm sounds for

1 minute or until any button is pressed. If no buttons are pressed, the alarm will

stop and the RAIN ALARM icon will ash for up to 30 minutes.

NOTE: The FLOOD WATCH ALARM and RAIN ALARM are NOT intended to

be a safety device or warning system.

Inhaltsverzeichnis

Andere ACU-RITE Wetterstation Handbücher

ACU-RITE

ACU-RITE 02081 Bedienungsanleitung

ACU-RITE

ACU-RITE 00595 Bedienungsanleitung

ACU-RITE

ACU-RITE 00806 Bedienungsanleitung

ACU-RITE

ACU-RITE 06020 Bedienungsanleitung

ACU-RITE

ACU-RITE 1015 Bedienungsanleitung

ACU-RITE

ACU-RITE 02036WB Bedienungsanleitung

ACU-RITE

ACU-RITE 00639W Bedienungsanleitung

ACU-RITE

ACU-RITE 622 Bedienungsanleitung

ACU-RITE

ACU-RITE 06006 Bedienungsanleitung

ACU-RITE

ACU-RITE 06058 Bedienungsanleitung

ACU-RITE

ACU-RITE 00821SBDI Bedienungsanleitung

ACU-RITE

ACU-RITE 06021 Bedienungsanleitung

ACU-RITE

ACU-RITE 02099 Bedienungsanleitung

ACU-RITE

ACU-RITE 01193M Bedienungsanleitung

ACU-RITE

ACU-RITE 01202 Bedienungsanleitung

ACU-RITE

ACU-RITE 00806SBL Bedienungsanleitung

ACU-RITE

ACU-RITE 1602RX Bedienungsanleitung

ACU-RITE

ACU-RITE 2010 Bedienungsanleitung

ACU-RITE

ACU-RITE 75077 Bedienungsanleitung

ACU-RITE

ACU-RITE 02099 Bedienungsanleitung

ACU-RITE

ACU-RITE 01139 Bedienungsanleitung

ACU-RITE

ACU-RITE 06095 Bedienungsanleitung

ACU-RITE

ACU-RITE Weather Forecaster 00821 Bedienungsanleitung

ACU-RITE

ACU-RITE 00829 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86371 Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2210 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-811561 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung