ACU-RITE 02032CAUDI Bedienungsanleitung

Instruction Manual

SAVE THIS MANUAL FOR FUTURE REFERENCE.

Questions? Contact Customer Support at

(877) 221-1252 or visit www.AcuRite.com.

CONTENTS

Unpacking Instructions ........... 2

Package Contents .................. 2

Features & Benets: 5-in-1....... 3

Features & Benets: Display.... 4

Back of Display Unit............... 6

Setup .................................... 7

5-in-1 Sensor Setup ................ 7

Display Unit Setup ................. 8

PC Connect for Windows ....... 9

Setup AcuLink Software.........11

Set the Time, Date & Units .....12

Backlight Settings..................12

Placement Guidelines ............13

5-in-1 Sensor Installation........14

Using the Weather Center .....15

Rainfall Tracking ...................16

Weather Ticker .....................17

Troubleshooting ....................18

Care & Maintenance.............21

Calibration ...........................21

Specications....................... 23

FCC Information .................. 23

Customer Support .................24

Professional Weather Center

model 02032CAUDI

Congratulations on your new AcuRite product. To ensure the best

possible product performance, please read this manual in its entirety

and retain it for future reference.

Unpacking Instructions

Remove the protective lm that is applied to the LCD screen prior to using this

product. Locate the tab and peel off to remove.

Package Contents

1. Display unit with tabletop stand

2. 5-in-1 sensor

3. Sensor mounting bracket

4. Mounting hardware

5. Snap-in debris lter for rain collector

6. Power adapter

7. USB cable

8. Instruction Manual

9. 4 Alkaline Batteries

Features & Benets

5-in-1 SENSOR

1. Rainfall Collector Funnel

2. Solar Cell Panel

Converts sunlight into power to run

internal aspirating fan.

Internal Aspirating Fan

(not shown)

Draws ambient air into

sensor to reduce solar radiation

heating, resulting in more accurate

temperature measurement.

3. A-B-C Switch

ID code that must match display’s

A-B-C switch to ensure units

synchronize.

4. Battery Compartment

5. Temperature & Humidity Sensors

(internal)

6. Mounting Point

7. Wind Speed Anemometer

8. Wind Direction Vane

9. Mounting Bracket

10. Mounting Hardware

Includes anchors & screws.

Qty Diameter Length

5 #4 19.05 mm (3/4”)

1 #4 12.7 mm (1/2”)

1 #6 12.7 mm (1/2”)

11. Debris Filter

Snaps into rain collector to lter out

twigs, leaves, etc.

Features & Benets: Display

1 432 5

1718192021

1. Previous 2 Wind Directions

2 . Backlight Button

3. Current Wind Speed

4. Current Wind Direction

5. Current Indoor Temperature

Arrow icon indicates direction

temperature is trending.

6. Display Low Battery Indicator

7. Peak Wind Speed

Highest speed from the last 60

minutes.

8. Current Indoor Humidity

Arrow icon indicates direction

humidity is trending.

9. Clock

10. Rainfall Alert Indicator

Indicates rainfall of more than

25.4 mm of rain in 2 hours or less.

11. AUTO DIM Indicator

12. Current Rainfall

Accumulates data during rainfall.

13. 12 to 24 Hour Weather Forecast

Self-Calibrating Forecasting pulls

data from your 5-in-1 sensor to

generate your personal forecast.

14. Storm Alert Indicator

15. Month/Year/All-Time Rainfall

16. Current Barometric Pressure

Arrow icon indicates direction

pressure is trending.

17. RAINFALL Button

Press to change the RAINFALL

data being displayed (Month, Year,

All-Time).

18. TButton

for setup preferences.

19. SET Button

for setup preferences.

20.

Button

for setup preferences.

21. SELECT Button

Press to change the WEATHER

SELECT category data being

displayed.

22. Weather TickerTM

Use “T” or “

“ to cycle through

messages.

23. Heat Index/ Wind Chill Alert

Indicator

24. Learning Mode Icon

Disappears after weather forecast

self-calibration is complete.

25. WEATHER SELECT

Displays heat index, dew point, wind

chill, feels like, days with rain this

month, and days since last recorded

rainfall.

26. Date

27. Current Outdoor Humidity

Arrow icon indicates direction

humidity is trending.

28. Average Wind Speed

of all speeds from past 2 minutes.

29. 5-in-1 Sensor Signal Strength

30. Sensor Low Battery Indicator

31. Current Outdoor Temperature

Arrow icon indicates direction

temperature is trending.

Back of Display Unit

123 4

BACK OF DISPLAY UNIT

1. Plug-in for Power Adapter

2. Plug-in for USB Cable

3. Integrated Hang Hole

for easy wall mounting

4. MAC ADDRESS

12 digit unique ID required for

online connectivity functions

5. Backup Battery Compartment

6. A-B-C Switch

ID code that must match 5-in-1

sensor’s A-B-C switch to ensure

units synchronize

7. CLEAR RECORD/ RESET

Press and HOLD for full reset

to factory defaults.

8. Power Adapter

9. USB Cable for PC Connection

10. Battery Compartment Cover

(not shown)

A B C

SETUP

5-in-1 Sensor Setup

1A-B-C Switch

Set to match

display unit

2Install Batteries

4 AA Batteries

3Rain Gauge Stabilizer

Remove and discard

Set the A-B-C Switch

Locate the A-B-C switch inside the

battery compartment. Set the A-B-C

switch to A, B or C. You must select

the same letter choices for both the

sensor and the display unit in order

for the units to synchronize.

Install or Replace Batteries

Batteries MUST be installed for

this product to operate. AcuRite

recommends high quality alkaline

or lithium batteries for the best

product performance. Heavy duty

or rechargeable batteries are not

recommended.

The 5-in-1 sensor requires lithium

batteries in low temperature

conditions. Cold temperatures can

cause alkaline batteries to function

improperly. Use lithium batteries in

the 5-in-1 sensor for temperatures

below -20ºC / -4ºF.

1. Slide off the battery

compartment cover.

2. Insert 4 x AA batteries into the

battery compartment, as

shown. Follow the polarity

(+/-) diagram in the battery

compartment.

3. Replace the battery cover.

Remove Rain Gauge Stabilizer

Locate and remove the rain gauge

stabilizer (plastic tab) taped into

the bottom of the sensor. The rain

gauge will not function until this is

removed.

Display Unit Setup

Set the A-B-C Switch

The A-B-C switch is located inside

the battery compartment. It can

be set to A, B or C. However,

you must select the same letter

choices for both the sensor and

the display unit in order for the

units to synchronize.

Plug Power Adapter into

Electric Outlet

Write Down the MAC ADDRESS

12 digit unique ID needed for

online connectivity functions.

Install or Replace Backup

Batteries (optional)

Insert 3 x AA alkaline batteries

into the battery compartment,

as shown. Follow the polarity

(+/-) diagram in the battery

compartment.

PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE

WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.

BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to

be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of

used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries

in re, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT

recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.

4Install Backup

Batteries

3 AA Batteries

3Write Down

MAC ADDRESS

12 digit number

A B C

1A-B-C Switch

set to match

sensor

IMPORTANT: Batteries are a backup

power source to preserve records

in the event of a power outage.

Power adapter is the recommended

primary power source to enjoy the full

functionality of this product.

24 C8 6E

2Plug in Power

Adapter

PC Connect for Windows Overview

PC Connect for Windows lets you access your Weather Center data in the

following ways:

• Data File: Display unit logs (or stores) data so that you can download it to a

PC in a data le (CSV, or comma-separated values le).

• PC Weather Widget: View data on your PC’s screen as a widget.

• Web Browser or Smartphone: Monitor sensor data remotely using AcuRite’s

free AcuRite online software, or from a mobile device using the free AcuRite

app, available from the iOS App Store or

Google Play Store.

PC Connect for Windows

USB Modes

To setup PC Connect for Windows, you must

rst select a USB mode on the display unit.

Note: The PC Connect for Windows software

MUST be installed on your computer BEFORE

connecting the display unit to the computer.

Mode 1: Display Logging ON

•Display unit logs (stores) up to 2 weeks of

data in memory. When memory nears

capacity, display unit’s Weather Ticker

displays an alert to download memory soon.

•Transfer data to your PC using PC Connect for Windows.

Mode 2: Display Logging OFF (DEFAULT)

•Display unit DOES NOT log (save) any data in memory for PC transfer.

Mode 3: Display Logging ON/Internet Bridge Mode

•Display unit logs (stores) up to 2 weeks of data in memory.

•Transfer data to your PC using PC Connect for Windows.

•Stream your data from your weather center to online sources.*

Mode 4: Display Logging OFF/Internet Bridge Mode

•Display unit DOES NOT log (save) any data in memory.

•Stream your data from your weather center to online sources.*

* PC and internet connection must remain ON to continuously stream data

from your weather center to online sources or the AcuRite mobile app.

Stores

Data

Shows

Data

USB

Mode Streams

Online*

DISPLAY UNIT...

Download the PC Connect for Windows Software

The PC Connect for Windows software is available online as a free download.

An instruction manual for PC Connect for Windows is included (PDF le) when

you download the software. Read the manual to learn how to setup

PC Connect for Windows preferences and features.

Download PC Connect for Windows software to your computer by visiting:

http://www.AcuRite.com/pc-connect-download

Or, you can navigate to the page above using the following path:

www.acurite.com > Support > Manuals & Downloads > Downloads > PC Connect

Click the “setupacu-link” le you downloaded and follow the on-screen

instructions to install the PC Connect for Windows software. A folder

named “AcuRite” will be installed on your computer.

After PC Connect for

Windows is installed on

your computer, open the

PC Connect app. Verify

that the display unit is

powered on with the AC

power adapter plugged

in, then connect the small end of the USB cable into the USB port located

inside the battery compartment on the back of the display unit.

Connect the larger end of the

USB cable into a USB port on

your computer.

USB functions on the display

unit are OFF by default. Verify

the display unit is powered on and receiving data from the outdoor

sensor. Next, set the mode on the display unit. Set to mode 3 for full PC

Connect for Windows functionality, or see page 9 for a description of all

available modes.

Select the SAME USB mode in the PC Connect for Windows software that

you chose on your display unit.

PC Connect for Windows is now ready for use. Please note that it may

take up to 1 minute for the PC Connect for Windows software to begin

receiving data from the display unit.

(PC)

Inhaltsverzeichnis

Andere ACU-RITE Wetterstation Handbücher

ACU-RITE

ACU-RITE 2030 Bedienungsanleitung

ACU-RITE

ACU-RITE 01518 Bedienungsanleitung

ACU-RITE

ACU-RITE 00777 Bedienungsanleitung

ACU-RITE

ACU-RITE 02001 Bedienungsanleitung

ACU-RITE

ACU-RITE 02050CAUDI Bedienungsanleitung

ACU-RITE

ACU-RITE 02027 Bedienungsanleitung

ACU-RITE

ACU-RITE 02001 Bedienungsanleitung

ACU-RITE

ACU-RITE 1050 Bedienungsanleitung

ACU-RITE

ACU-RITE 8575 Bedienungsanleitung

ACU-RITE

ACU-RITE 01129 Bedienungsanleitung

ACU-RITE

ACU-RITE 06018RM Bedienungsanleitung

ACU-RITE

ACU-RITE 01515 Bedienungsanleitung

ACU-RITE

ACU-RITE 992 Bedienungsanleitung

ACU-RITE

ACU-RITE 02099 Bedienungsanleitung

ACU-RITE

ACU-RITE 02010 Bedienungsanleitung

ACU-RITE

ACU-RITE 06006RM Bedienungsanleitung

ACU-RITE

ACU-RITE 992 Bedienungsanleitung

ACU-RITE

ACU-RITE 00639W Bedienungsanleitung

ACU-RITE

ACU-RITE 01536CAUDI Bedienungsanleitung

ACU-RITE

ACU-RITE 01193M Bedienungsanleitung

ACU-RITE

ACU-RITE 615 Bedienungsanleitung

ACU-RITE

ACU-RITE 00787 Bedienungsanleitung

ACU-RITE

ACU-RITE 2038 Bedienungsanleitung

ACU-RITE

ACU-RITE 06095 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86371 Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2210 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-811561 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung