ADJ Inno Pocket Wash Bedienungsanleitung

User Instructions

9/14

specications, diagrams, images, and instructions herein are

subject to change without notice. ADJ Products, LLC logo and

identifying product names and numbers herein are trademarks

of ADJ Products, LLC. Copyright protection claimed includes all

forms and matters of copyrightable materials and information

now allowed by statutory or judicial law or hereinafter granted.

Product names used in this document may be trademarks or

registered trademarks of their respective companies and are

hereby acknowledged. All non-ADJ Products, LLC brands and

product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis-

claim any and all liabilities for property, equipment, building,

and electrical damages, injuries to any persons, and direct or

indirect economic loss associated with the use or reliance of

any information contained within this document, and/or as a

result of the improper, unsafe, unsucient and negligent as-

sembly, installation, rigging, and operation of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment.

Please turn o all electrical products when they are not in use. To

avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

Inno Pocket Wash

ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 3ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 2

• DMX-512 Protocol Compatible (4 DMX Channel Modes: 9 Chan-

nels, 11 Channels, 19 Channels, & 21 Channels)

• 3 Operating Modes - Sound Active, Show Mode, & DMX Control

• 5 Dimmer Curves (Standard, Stage, TV, Architectural, & Theatre)

• Internal Microphone

• Digital Display for Address and Function Setting

• 4 Preprogrammed Shows

• UC-IR Compatiable (Not Included)

Inno Pocket Wash Features

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact ADJ Products, LLC.

During operation the housing may become extremely hot. Avoid

touching the unit with bare hands while in use.

ADJ Products, LLC will not accept any liability for any resulting dam-

ages caused by the non-observance of this manual or any unauthor-

ized modication to this unit.

Inno Pocket Wash Handling Precautions

Inno Pocket Wash Warranty Registration

The Inno Pocket Wash carries a 2 year (730 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase

and warranty. You may also register your product online at www. adj-

products.com. All returned service items whether under warranty or

not, must be freight pre-paid and accompany a return authorization

(R.A.) number. If the unit is under warranty you must provide a copy

of your proof of purchase invoice. Please contact ADJ Products, LLC

customer support for a R.A. number.

To optimize the performance of this product, please read these

operating instructions carefully to familiarize yourself with the basic

operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please

keep this manual with the unit, for future reference.

Inno Pocket Wash General Instructions

Inno Pocket Wash General Information

Unpacking: Thank you for purchasing the Inno Pocket Wash by ADJ

Products, LLC. Every Inno Pocket Wash has been thoroughly tested

and has been shipped in perfect operating condition. Carefully check

the shipping carton for damage that may have occurred during ship-

ping. If the carton appears to be damaged, carefully inspect your x-

ture for any damage and be sure all equipment necessary to operate

the unit has arrived intact. In the event damage has been found or parts

are missing, please contact our toll free customer support number for

further instructions. Please do not return this unit to your dealer with-

out contacting customer support rst.

Introduction: The Inno Pocket Wash is a DMX intelligent, moving

head, mini LED was. The Inno Pocket Wash can operate as a stand

alone fixture or in a Master/Slave set up. The Inno Pocket Wash has

three operating modes; a sound active, show mode, DMX controlled.

This fixture is suitable for theaters, studios, retail stores, and other

similar locations. For best results use fog or special effects smoke to

enhance the beams projections.

Customer Support: ADJ Products, LLC provides a toll free cus-

tomer support line, to provide help and to answer any question should

you encounter problems during your set up or initial operation. You

may also visit us on the web at www.adj.com for any comments or

suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: support@americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break o the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 29 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits

a marked change in performance.

Inno Pocket Wash Safety Precautions

ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 5ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 4

The Inno Pocket Wash is fully operational in two dierent mounting

positions, hanging upside-down from a ceiling or set on a at level

surface. To avoid internal damage to the unit, never mount the unit on

its side as illustrated above. Be sure this xture is kept at least 0.5m

away from any ammable materials (decoration etc.). Always use

and install the supplied safety cable as a safety measure to prevent

accidental damage and/or injury in the event the clamp fails (see next

page).

When installing the unit, the trussing or area of installation must be

able to hold 10 times the weight without any deformation. When

installing the unit must be secured with a secondary safety attach-

ment, e.g. and appropriate safety cable. Never stand directly below

the unit when mounting, removing, or servicing the unit.

Overhead mounting requires extensive experience, including calculat-

ing working load limits, installation material being used, and perodic

safety inspection of all installation material and unit. If you lack these

qualications, do not attempt the installation yourself.

The installaiton should be checked by a skilled person once a year.

Inno Pocket Wash Mounting

ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 6 ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 7

Power Supply: The ADJ Inno Pocket Wash contains a automatic

voltage switch, which will auto sense the voltage when it is plugged

into the power source. With this switch there is no need to worry about

the correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of dierent manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave

Operation): The Inno Pocket Wash can be controlled via DMX-512

protocol. The Inno Pocket Wash four DMX channel modes; 9 channel

mode, 11 channel mode, 19 channel mode, & 21

channel mode. The DMX address is set electroni-

cally using the controls on the front panel of the

unit. Your unit and your DMX controller require a

approved DMX-512 110 Ohm Data cable for data

input and data output (Figure 1). We recommend

Accu-Cable DMX cables. If you are making your

own cables, be sure to use standard 110-120 Ohm

shielded cable (This cable may be purchased at

Inno Pocket Wash DMX Set Up

Figure 1

Screw one clamp via a M12 screw and nut to the included

bracket. Attach the bracket using the included screws to the

bottom of the Inno Pocket Wash. Attach the eyehole screw to

the bottom of the base and pull the safety-cable through the

screw and over the trussing system or a safe xation spot.

Insert the end in the carabine and tighten the safety screw.

NOTICE: The suitable enviromental temperature for this light-

ing xture is between -25˚ C to 45˚ C. Do not place this lighting

xture in an enviroment where the temperatures are under or

above the temperatures stated above. This will allow the xture

to run at its best and help prolong the xture life.

Inno Pocket Wash Mounting

ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 9ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 8

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Inno Pocket Wash DMX Set Up

almost all professional sound and lighting stores). Your cables should

be made with a male and female XLR connector on either end of the

cable. Also remember that DMX cable must be daisy chained and

cannot be split.

Inno Pocket Wash DMX Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 10 ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 11

Inno Pocket Wash System Menu

System Menu: When making adjustments press ENTER to

conrm your setup then press and hold the MENU button

for at least 3 seconds. To exit without making any adjust-

ments press the MENU button. The display will lock after 30

seconds, press the MENU button for 3 seconds to unlock.

ADDR - DMX Address Setting.

1. Press the either the MENU, UP, or DOWN buttons until

“ADDR” is displayed, press ENTER.

2. The current address will now be displayed and ashing.

Press the UP or DOWN buttons to nd your desired address.

Press ENTER to set your desired DMX address.

CHND - This will let select your desired DMX channel

mode.

1. Press the either the MENU button until “CHND” is displayed,

press ENTER. Either “9CH”, “11CH”, “19CH”, or “21CH” will be

displayed

2. Press the UP or DOWN buttons to nd your desired DMX

channel mode and press ENTER to conm and exit.

SLND - This will let you set unit as a master or slave in a

master/slave conguration.

1. Press the MENU button until “SLND” is displayed, press

ENTER. Either “MAST”, “SL 1”, or “SL 2” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is

displayed, press ENTER to conm.

NOTE: In a Master/Slave conguration you can set one xture

to Master and then set the next xture to “SL 2”, the xtures

will now have contrast movement to each other.

Inno Pocket Wash System Menu

ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 12 ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 13

DNST - This mode can be used as a precaution mode,

that in case the DMX signal is lost, interrupted, or power is

lost, the operating mode chosen in the setup is the running

mode the xture will go into when the DMX signal is lost. You

can also set this as the operating mode you would like the

unit to return to when power is applied.

1. Press the MENU button until “DNST” is displayed, and either

“MASL”, “BLND”, or “LAST” will be displayed beneath.

2. Press ENTER and the bottom choice will begin to ash. Use

the UP or DOWN buttons to choose an operating mode you

would like the unit to start up in when power is applied or the

DMX signal is lost.

• LAST - If the DMX signal is lost the xture will stay in the last

DMX setting. If power is applied and this mode is set, the unit will

automatically go into the last DMX set up.

• MASL (Master Slave) - If the DMX signal is lost or power is

applied, the unit will automatically go into Master Slave mode

and run a built-in show.

• BLND (Blackout) - If the DMX signal is lost or interrupted, the

unit will automatically go into stand by mode.

3. Press ENTER to conrm your desired set up.

DIND - This will let select your desired dimmer curve.

1. Press the either the MENU button until “DIND” is displayed,

press ENTER. 1 of 5 dimmer curves will be displayed. “STDA”

(standard), “STGE” (stage), “TV” (TV), “ARAL” (Architectural),

or “THAL” (Theatre).

2. Press the UP or DOWN buttons to nd your desired dimmer

curve and press ENTER to conm and exit.

Inno Pocket Wash System Menu

SHND - Show modes 0-4 (Factory programs). Show

mode can run with or without sound active mode active.

1. Press the MENU button until “SHND” is displayed, press

ENTER.

2. “Sh X” will now be displayed, “X” representing a number

between 0-4. Shows 1-4 are factory programs, while show “0” is

random mode. Use the UP or DOWN buttons to nd your desired

show.

3. When you have found your desired show press ENTER, then

press and hold the MENU button for at least 3 seconds to acti-

vate. After you have set your desired show, it can be changed

at any time using the UP or DOWN buttons.

SOUN - Sound Active mode.

1. Press the MENU button until “SOUN” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to activate sound active mode,

or “OFF” to deactivate sound active mode.

3. Press ENTER to conrm.

SENS - In this mode you can adjust the sound sensitiv-

ity.

1. Press the MENU button until “SENS” is displayed, press

ENTER.

2. A number between 0-100 will be displayed. Press the UP or

DOWN buttons to adjust the sound sensitivity. 0 being the least

sensitive, and 100 being the most sensitive.

3. When you have found your desired setting press ENTER to

conrm.

Inno Pocket Wash System Menu

ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 15ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 14

PINT - Pan Inversion

1. Press the MENU button until “PINT” is displayed, press

ENTER. Either “Yes” or “No” will be displayed.

2. To activate the Pan inversion press the UP or DOWN buttons

until “Yes” is displayed, press ENTER to conm. To deactivate

Pan inversion, select “No” and press Enter.

TINT - Tilt Inversion

1. Press the MENU button until “TINT” is displayed, press

ENTER. Either “Yes” or “No” will be displayed.

2. To activate the tilt inversion press the UP or DOWN buttons

until “Yes” is displayed, press ENTER to conm. To deactivate

tilt inversion, select “No” and press Enter.

LED - With this function you can have the display back-

light turn off after 10 seconds.

1. Press the MENU button until “LED” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to keep the LED display on at

all times, or “OFF” to switch to have the LED display switch o

after 10 seconds.

3. Press ENTER to conrm. To make you LED display reappear

again press any button.

DISP - This function will reverse the display 180º.

1. Press the MENU button until “DISP” is displayed, press

ENTER.

2. Press ENTER to “ip” the display. Press ENTER to “ip” it

Inno Pocket Wash System Menu

again. Press ENTER when you have made your desired setup.

TEST - This function will run a self test program.

1. Press the MENU button until “TEST” is displayed, press

ENTER.

2. The xture will now run a self test.

MANU - In this submenu you are able to test the different

functions; pan, tilt, LEDs, dimmer, and strobe.

1. Press the MENU button until “MANU” is displayed, press

ENTER.

2. Use the UP and DOWN buttons to scroll through the various

functions able for testing. Once you have found your desired

function you would like to test press ENTER.

3. After you have pressed ENTER, use the UP and DOWN but-

tons to adjust the values and test the function. To exit press the

MENU button.

TEMP - With this function you can check the temperature

of the xture.

1. Press the MENU button until “TEMP” is displayed, press

ENTER.

2. The xture temperature will now be displayed. Press MENU

to exit.

FHRS - With this function you can display the running

time of the unit.

1. Press the MENU button until “FHRS” is displayed, press

ENTER.

Inno Pocket Wash System Menu

ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 16 ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 17

Inno Pocket Wash Home Adjustment Menu

2. The running time of the xture will now be displayed. Press

MENU to exit.

VER - Use this function to display the Software version of

the unit.

1. Press the either the MENU button until “VER” is displayed,

press ENTER.

2. The display will show the software version.

RSET - Use this function to reset the unit.

1. Press the MENU button until “RSET” is displayed, press

ENTER.

2. The xture will now reset.

BALA - With this function you are able to adjust the RGB

colors to create your desired shade of white.

1. Press the MENU button until “BALA” is displayed, press

ENTER.

2. Use the UP and DOWN buttons to scroll through the RGB

colors. Once you have found your desired color you would like

to adjust press ENTER.

3. After you have pressed ENTER, use the UP and DOWN but-

tons to adjust the intensity of the color. Continue to adjust the

RGB colors until you have reached your desired shade of white.

Inno Pocket Wash System Menu

To enter the home position adjustment menu, press the ENTER

button for at least 5 seconds. In this submenu you are able to

adjust the original position of the pan position and tilt position.

PAN - Adjustment of the pan position.

1. Press the ENTER button for at least 5 seconds, then press

the UP or DOWN buttons so that “PAN” is displayed, press

ENTER.

2. Use the UP and DOWN buttons to make your adjustments,

and then press ENTER to conrm. Press the MENU button for

one second to exit.

TILT - Adjustment of the tilt position.

1. Press the ENTER button for at least 5 seconds, then press

the UP or DOWN buttons so that “TILT” is displayed, press

ENTER.

2. Use the UP and DOWN buttons to make your adjustments,

and then press ENTER to conrm. Press the MENU button for

one second to exit.

ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 18 ADJ Products, LLC - www.adj.com - Inno Pocket Wash Instruction Manual Page 19

Inno Pocket Wash Master-Slave Set Up

Master-Slave Operation This function will allow you to link up to 16

units together and operate without a controller. The units will be sound

activated. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units programs. Any unit

can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the

Male XLR connector is the input and the Female XLR connector

is the output. The rst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male

XLR connector only. For longer cable runs we suggest a termina-

tor at the last fixture.

2. On the Master unit press the MENU button until “SLND” is dis-

played, and press ENTER. Use the UP and DOWN buttons to

scroll to the “MAST” setting and press ENTER.

3. After setting the Master unit to the master setting find and set

your desired operating mode.

4. On the slave units press the MENU button until “SLND” is dis-

played, and press ENTER. Choose either “SL 1” or “SL 2” and

press ENTER. See page 11 for more info.

5. The slave units will now follow the Master unit.

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to control the chases and patterns,

dimmer and strobe. A DMX controller allows you to create unique

programs tailored to your individual needs.

1. The Inno Pocket Wash has 4 DMX channel modes; 9 channel

mode, 11 channel mode, 19 channel mode, and 21 channel

mode. See pages 21-28 for detailed description of the DMX val-

ues and traits.

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 7-9 as well as the set-up specifications that are includ-

ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instruction on page 11 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

Sound Active Mode: This mode allows either single unit or several

units linked together, to run to the beat of the music.

1. Press the MENU button until “SOUN” is displayed, and press

ENTER. Press the UP or DOWN buttons so that “ON” is dis-

played and press ENTER.

2. Press the MENU button until “SENS” is displayed, and press

ENTER. Use the UP and DOWN buttons to adjust the sound

sensitivity. Press ENTER when you have found your desired sensi-

tivity level.

Show Mode: This mode allows either a single unit or several units

linked together, to run one of four shows that you choose.

1. Press the MENU button until “SHND” is displayed, and press

ENTER.

2. Press the UP or DOWN buttons to nd your desired show, and

press ENTER.

Inno Pocket Wash Operation

Inhaltsverzeichnis

Andere ADJ DJ-Equipment Handbücher

ADJ

ADJ ELEMENT QA Bedienungsanleitung

ADJ

ADJ Bubbletron Go Bedienungsanleitung

ADJ

ADJ XPress LED Bedienungsanleitung

ADJ

ADJ Par Z Move RGBW Bedienungsanleitung

ADJ

ADJ VIZI BEAM 12RX Bedienungsanleitung

ADJ

ADJ MB DMX II Bedienungsanleitung

ADJ

ADJ STARSHIP Bedienungsanleitung

ADJ

ADJ M-103HD Bedienungsanleitung

ADJ

ADJ ENCORE BURST 200 Bedienungsanleitung

ADJ

ADJ HEX206 Bedienungsanleitung

ADJ

ADJ COB CannOn Wash DW Bedienungsanleitung

ADJ

ADJ 6-PACK SKB CASE Bedienungsanleitung

ADJ

ADJ VF FLURRY Bedienungsanleitung

ADJ

ADJ SCENE SETTER 48 Bedienungsanleitung

ADJ

ADJ Dotz Par Bedienungsanleitung

ADJ

ADJ PinPoint Gobo COLOR Bedienungsanleitung

ADJ

ADJ MOD STQ Bedienungsanleitung

ADJ

ADJ FOCUS BEAM LED Bedienungsanleitung

ADJ

ADJ Vision Series Bedienungsanleitung

ADJ

ADJ Encore Profile 1000 WW Bedienungsanleitung

ADJ

ADJ 7P HEX IP Bedienungsanleitung

ADJ

ADJ TRI18XS Bedienungsanleitung

ADJ

ADJ VIZI CMY 16RX Bedienungsanleitung

ADJ

ADJ 32 HEX PANEL IP Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung