ADJ Ikon profile ww Bedienungsanleitung

User Instructions

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

The Netherlands

www.americandj.eu

7/16

A.D.J. Supply Europe B.V. –www.americandj.eu –Ikon Profile WW Instruction Manual Page 2

herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and

numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and

matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter

granted. Product names used in this document may be trademarks or registered trademarks of their respective

companies and are hereby acknowledged. All non-ADJ Products, LLC brands and product names are

trademarks or registered trademarks of their respective companies.

ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment,

building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with

the use or reliance of any information contained within this document, and/or as a result of the improper,

unsafe, unsufficient and negligent assembly, installation, rigging, and operation of this product..

A.D.J. Supply Europe B.V. –www.americandj.eu –Ikon Profile WW Instruction Manual Page 3

Contents

INTRODUCTION.......................................................................................................................................................................4

PRECAUTIONS .........................................................................................................................................................................4

FIXTURE LAYOUT.....................................................................................................................................................................5

SYSTEM MENU........................................................................................................................................................................6

DMX VALUES & TRAITS ...........................................................................................................................................................8

CAD DRAWING........................................................................................................................................................................8

GOBO REPLACEMENT .............................................................................................................................................................8

ADDING A COLOR GEL.............................................................................................................................................................8

INSTALLATION.........................................................................................................................................................................9

PHOTOMETRIC CHART..........................................................................................................................................................10

GOBOS ....................................................................................................................................................................................9

ADJ UC IR CONTROL..............................................................................................................................................................10

POWER CORD DAISY CHAIN..................................................................................................................................................11

TROUBLE SHOOTING.............................................................................................................................................................11

FUSE REPLACEMENT .............................................................................................................................................................11

CLEANING..............................................................................................................................................................................11

SPECIFICATIONS....................................................................................................................................................................12

ROHS - A great Contribution to the Conservation of Environment.....................................................................................13

WEEE –Waste of Electrical and Electronic Equipment ........................................................................................................14

NOTES ...................................................................................................................................................................................15

NOTES ...............................................................................................................................Fehler! Textmarke nicht definiert.

A.D.J. Supply Europe B.V. –www.americandj.eu –Ikon Profile WW Instruction Manual Page 4

INOZIONE

INTRODUCTION

To optimize the performance of this product, please read these operating instructions carefully to familiarize

yourself with the basic operations of this unit. These instructions contain important safety information regarding

the use and maintenance of this unit. Please keep this manual with the unit, for future reference.

Unpacking:

Thank you for purchasing the Ikon Profile WW by ADJ Products, LLC.

Every Ikon Profile WW has been thoroughly tested and has been shipped in perfect operating condition.

Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears

to be damaged, carefully inspect your unit for any damage and be sure all equipment necessary to operate the

system has arrived intact. In the event damage has been found or parts are missing, please contact our toll

free customer support number for further instructions. Please do not return the unit to your dealer without first

contacting customer support.

Customer Support:If you encounter any problems, please contact your trusted American Audio shop. We

also offer the possibility, to contact us directly: You can contact us via our website www.americandj.eu or via

email: support@americandj.eu

Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

Caution! This may cause eye damage. Avoid looking directly into the light source. Use sensible precaution.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will

void your manufactures warranty. In the unlikely event your unit may require service please contact ADJ

Products, LLC.

PLEASE do not discard the shipping carton in the trash. Please recycle when ever possible..

PRECAUTIONS

Safety Issue: This unit may blow the fuse if the maximum allotted load of 2 amps is reached. If the fuse needs

replacement, please see fuse replacement on page 10.

• Be sure the local power outlet match the required voltage of the unit.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between

this device and a wall.

• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the fixture. Do not attempt to remove or break off the ground

prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an

internal short.

• The fixture should be serviced by qualified service personnel when:

A. The power cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a marked change in performance.

A.D.J. Supply Europe B.V. –www.americandj.eu –Ikon Profile WW Instruction Manual Page 5

FIXTURE LAYOUT

1. LED:

DMX

DMX input present

MASTER

Master Mode

SLAVE

Slave Mode

2. Button:

To select the programming functions

To go forward in the selected functions

DOWN

To go backward in the selected functions

ENTER

To confirm the selected functions

3. Fuse (T 2A): Protect the unit from damage of over current

4. Display: To show the various menus and the selected function

5. Power In/Out: Power cable input/output connections

6. DMX In/Out: 3-pin XLR connections for DMX 512 operation

7. Flags: Use thes e to a dju st the fram ing of your g obo

8. Knobs: Move to adjust the beam angle from 15 to 4 0 degree and to focus the gobo

9. Spring: To lock the color gel frame into place

A.D.J. Supply Europe B.V. –www.americandj.eu –Ikon Profile WW Instruction Manual Page 6

SYSTEM MENU

System Menu

DMX Address

Slave Mode

DMX Last State

Dimmer Mode

Back Light

Display

Manual Test

Auto Test

Fixture Temperature

Fixture Hours

Software Version

SYSTEM MENU

On-Board System Menu. The Ikon Profile WW comes with an easy to navigate system menu. This next

section will detail the functions of each command in the system menu. Please read the next section

thoroughly!

To access the main menu press the MENU button. Press the UP or DOWN buttons until you reach function

you wish to change. When you reach the function you wish to change press the enter button. When a function

is selected use the UP or Down buttons to change the function settings. Once your changes are made press

the enter button, and then press and hold the MENU button for at least three seconds to confirm and lock the

change into the system memory. If the menu button is not pressed and held within eight seconds the fixture

will automatically confirm and lock the change into the system memory. To exit without making any changes

press the MENU button.

ADDR - DMX Address Setting.

1. Press the MENU button until “ADDR” is displayed, press ENTER.

2. The current DMX address will now be displayed and flashing. Press the UP or DOWN buttons to find your

desired address. Press ENTER to set your desired DMX address.

NOTE: If after you connect your DMX controller the unit does not fall into DMX mode, press and hold the

MENU button for at least 3 seconds.

SLND - This will let you set unit as a master or slave in a master/slave configuration.

1. Press the MENU button until “SLND” is displayed, press ENTER. “MAST” or “SL 1” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim and exit.

A.D.J. Supply Europe B.V. –www.americandj.eu –Ikon Profile WW Instruction Manual Page 7

SYSTEM MENU (continued)

DNST - This mode can be used as a precaution mode, that in case the DMX signal is lost, interrupted,

or power is lost, the operating mode chosen in the setup is the running mode the fixture will go into

when the DMX signal is lost. You can also set this as the operating mode you would like the unit to

return to when power is applied.

1. Press the MENU button until “DNST” is displayed, and either “MASL”, “BLND”, or “LAST” will be displayed

beneath.

2. Press ENTER and the bottom choice will begin to flash. Use the UP or DOWN buttons to choose an

operating mode you would like the unit to start up in when power is applied or the DMX signal is lost.

• MASL (Master Slave) - If the DMX signal is lost or power is applied, the unit will automatically go into Master

Slave mode and run a built-in show.

• BLND (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into stand by mode.

• LAST - If the DMX signal is lost the fixture will stay in the last DMX setting. If power is applied and this mode

is set, the unit will automatically go into the last DMX set up.

3. Press ENTER to confirm your desired set up.

DIND - This will let select your desired dimmer curve.

1. Press the MENU button until “DIND”is displayed, and press ENTER. 1 of 5 dimmer curves will be displayed.

“STDA” (standard), “STGE” (stage), “TV” (TV), “ARAL” (Architectural), or “THAL” (Theatre). See the dimmer

curve chart on page 10 for more info.

2. Press the UP or DOWN buttons to find your desired dimmer curve and press ENTER to confim and exit

LED - With this function the LED display will turn off after 2 minutes.

1. Press the MENU button until “LED” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to keep the LED

display on at all times, or “OFF” to allow the LED display to turn off after 2 minutes. Press any button to turn on

the LED display again.

3. Press ENTER to confirm and exit.

DISP - This function will reverse the display 180º.

1. Press the MENU button until “DISP” is displayed, press ENTER.

2. Press the UP button to select “DISP” to activate this function, or “DSIP” to deactivate this function.

3. Press ENTER to confirm.

MANU - In this submenu you are able to test the dimmer, and strobe.

1. Press the MENU button until “MANU” is displayed, press ENTER.

2. Use the UP and DOWN buttons to scroll through the various functions able for testing. Once you have found

your desired function you would like to test press ENTER.

3. After you have pressed ENTER, use the UP and DOWN buttons to adjust the values and test the function.

To exit press the MENU button.

TEST - This function will run a self test program.

1. Press the MENU button until “TEST” is displayed, press ENTER.

2. The fixture will now run a self test.

TEMP - With this function you can check the temperature of the fixture.

1. Press the MENU button until “TEMP” is displayed, press ENTER.

2. The fixture temperature will now be displayed. Press MENU to exit.

FHRS - With this function you can display the running time of the unit.

1. Press the MENU button until “FHRS” is displayed, press ENTER.

2. The display shows the running time of the unit. Press MENU to exit.

VER - Use this function to display the Software version of the unit.

1. Press the MENU button until “VER” is displayed, press ENTER.

2. The display will show the software version.

A.D.J. Supply Europe B.V. –www.americandj.eu –Ikon Profile WW Instruction Manual Page 8

DMX VALUES & TRAITS

Channel

Value

Function

0 - 7

8 - 15

16 - 131

132 - 139

140 - 181

182 - 189

190 - 231

232 - 239

240 - 247

248 - 255

STROBING/SHUTTER

CLOSED

OPEN

STROBE SLOW - FAST

OPEN

FAST CLOSE - SLOW OPEN

OPEN

SLOW CLOSE - FAST OPEN

OPEN

RANDOM STROBE

OPEN

0 - 255

MASTER DIMMER 0% - 100%

0 - 20

21 - 40

41 - 60

61 - 80

81 - 100

101 - 255

DIMMER MODE

STANDARD

STAGE

ARCHITECTURAL

THEATRE

DEFAULT DIMMER SETTING

CAD DRAWING

GOBO REPLACEMENT

The Ikon Profile WW gobo can be interchanged at any time and allows you to customize your system.

To replace gobo;

1. Gently slide the gobo housing out of the top of unit. The gobo housing is located in front of the top flag.

2. Once the gobo housing has been removed, remove the retaining ring that holds the gobo in. This can easily

be done using needle nose pliers.

3. Remove and replace the gobo with your desired replacement.

Reinsert the retainer ring, and make sure the ring rests firmly against the gobo.

4. Slide the gobo assembly back into place.

ADDING A COLOR GEL

A color gel (not included) can be added to the front of the Ikon Profile WW and can be interchanged at any

time. This allows you to customize your system.

To add a color gel;

1. Locate the color gel frame at the front of the unit. Slide the spring lever back and slide the gel frame out of

the holder.

2. Once the gel frame has been removed slide your desired color gel into the middle of the frame.

3. Slide the spring back and slide the gel frame into place.

A.D.J. Supply Europe B.V. –www.americandj.eu –Ikon Profile WW Instruction Manual Page 9

ADDING A COLOR GEL (continued)

Color gel splint

Spring

INSTALLATION

The unit should be mounted using a mounting clamp (not provided), affixing it to the mounting bracket that is

provided with the unit.

Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that

the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit’s

weight. Also, always use a safety cable that can hold 12 times the weight of the unit when installing the fixture.

The equipment must be installed by a professional, and it must be installed in a place where it is out of the

reach of people’s grasp.

GOBOS

A.D.J. Supply Europe B.V. –www.americandj.eu –Ikon Profile WW Instruction Manual Page 10

PHOTOMETRIC CHART

DIMMER CURVE CHART

Ramp Effect

0S(FadeTime)

1S (FadeTime}

Trise (ms)

Tdown (ms)

Trise (ms)

Tdown (ms)

Standard

Stage

780

1100

1540

1660

1180

1520

1860

1940

Architectural

1380

1730

2040

2120

Theatre

1580

1940

2230

2280

ADJ UC IR CONTROL

The UC IR (sold separately) infrared remote gives you control of various functions (See below). To control

the fixture you must aim the remote at the front of the fixture and be no more than 30 feet away.

The Airstream IR (sold separately) remote transmitter plugs into the headphone jack of your iOS phone or

tablet. To control your IR fixture, download the free Airstream IR app from the app store. After downloading the

app, plug the IR transmitter into the headphone jack of your iOS phone or tablet. Raise the volume to the

maximum level on your iOS phone or tablet and aim the transmitter at the fixture sensor and be no more than

15 feet away. The app comes with 3 pages of control depending on the fixture you are using. Please see

below for IR functions including the corresponding app page.

Works with App page 1.

STAND BY - Pressing this button will blackout the fixture.

FULL ON - This button is invalid for this fixture.

STROBE - Press and hold this button to activate strobing.

FADE/GOBO - This button is invalid for this fixture.

“DIMMER +” and “DIMMER -” - Use these buttons to adjust the output intensity.

1-9 - These buttons are invalid for this fixture.

SOUND ON & OFF - These buttons are invalid for this fixture.

SHOW - This button is invalid for this fixture.

Dimmer

Andere Handbücher für ikon profile ww

Inhaltsverzeichnis

Andere ADJ DJ-Equipment Handbücher

ADJ

ADJ Focus Spot Three Z Bedienungsanleitung

ADJ

ADJ WOLFMIX WMX1 Bedienungsanleitung

ADJ

ADJ BUBBLETRON Bedienungsanleitung

ADJ

ADJ HEX700 Bedienungsanleitung

ADJ

ADJ ENCORE LP12Z IP Bedienungsanleitung

ADJ

ADJ VIZI CMY300 Bedienungsanleitung

ADJ

ADJ WiFly QA5 IP Bedienungsanleitung

ADJ

ADJ UB 12H Bedienungsanleitung

ADJ

ADJ Mega Bar RGBA Bedienungsanleitung

ADJ

ADJ wifly bar qa5 Bedienungsanleitung

ADJ

ADJ ELEMENT H6 PAK Bedienungsanleitung

ADJ

ADJ ECO UV BAR PLUS IR Bedienungsanleitung

ADJ

ADJ ADJ-610 Bedienungsanleitung

ADJ

ADJ ENCORE BURST 200 Bedienungsanleitung

ADJ

ADJ FS3000LED Bedienungsanleitung

ADJ

ADJ Jolt Bar FX Bedienungsanleitung

ADJ

ADJ 5PX HEX PEARL Bedienungsanleitung

ADJ

ADJ PIXIE DRIVER 2000 Bedienungsanleitung

ADJ

ADJ POCKET PRO Bedienungsanleitung

ADJ

ADJ Gobo Motion LED Montageanleitung

ADJ

ADJ THEATRIX PRO 48 LED Bedienungsanleitung

ADJ

ADJ HYDRO WASH X7 Bedienungsanleitung

ADJ

ADJ VF FLURRY Bedienungsanleitung

ADJ

ADJ VIZI WASH Z19 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung

ADJ ikon profile ww Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken