ADJ VIZI WASH Z19 Bedienungsanleitung

User Instructions

VIZI WASH Z19

ENTER

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document

may be available online.

Please check www.adj.com for the latest revision/update of this manual before beginning

installation and/or programming.

Date Document

Version

Software

Version

DMX

Channel

Modes

Notes

07/23/19 11.2 12/16/28/44 Initial Release

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and opera-

tion of this product.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS

This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installa-

tion. This device uses and can radiate radio frequency energy and, if not installed and used in accordance

with the included instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this device does cause harmful

interference to radio or television reception, which can be determined by turning the device off and on, the

user is encouraged to try to correct the interference by one or more of the following methods:

· Reorient or relocate the device.

· Increase the separation between the device and the receiver.

· Connect the device to an electrical outlet on a circuit different from which the radio receiver is

connected.

· Consult the dealer or an experienced radio/TV technician for help.

ADJ Products, LLC - www.adj.com - Vizi Wash Z19 User Manual Page 2

Vizi Wash Z19 Table of Contents

Introduction

Features I Warranty Registration

Safety Guidelines

External Light Exposure

Installation

Overview

DMX Set Up

DMX Addressing

DMX Channel Modes

Color Macro Chart

System Menu

Pixel Zone Layout

Target Modes

Error Codes

Dimmer Curve Chart

Dimensional Drawings

Power Linking I Trouble Shooting I Cleaning

Limited Warranty (USA Only)

Technical Specications

ADJ Products, LLC - www.adj.com - Vizi Wash Z19 User Manual Page 3

Vizi Wash Z19 Introduction

Unpacking: Thank you for purchasing the Vizi Wash Z19 by ADJ Products, LLC. Every Vizi Wash Z19

has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the

shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit

has arrived intact. In the case damage has been found or parts are missing, please contact our toll free

customer support number for further instructions. Do not return this unit to your dealer without rst

contacting customer support.

Introduction: The ADJ Vizi Wash Z19 is a DMX intelligent, high powered, moving head fixture. To optimize

the performance of this product, please read these operating instructions carefully to familiarize yourself

with the basic operations of this unit. This product is intended to be used by professionally trained

personnel only and is not suitable for private use.

These instructions contain important safety information regarding the use and maintenance of this

unit. Please keep this manual with the unit, for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.americandj.com (US)

http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-832-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

+31 (0)45 546 85 00 | Fax +31 45 546 85 99

www.adj.eu | [email protected]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufactures warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

Vizi Wash Z19 Features

• Electronic Dimming 0-100%

• DMX-512 protocol

• Multiple DMX Channel Modes

• 3-Pin and 5-Pin In/Out DMX Connection

2 or 7 Pixel Zone Ring Control•

• Gamma Brightness Adjustment

• Pan/Tilt Target Mode

• Zoom

• 6 Dimmer Curves With Dimmer Adjustment Speed

• Multiple Unit Power Linking (See page 29)

Included:

1 x Twist Lock Power Cable

2 x Omega Brackets

Vizi Wash Z19 Warranty Registration

The Vizi Wash Z19 carries a 2 year limited warranty. Please fill out the enclosed warranty card to

validate your purchase. All returned service items whether under warranty or not, must be freight pre-

paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on

the outside of the return package. A brief description of the problem as well as the R.A. number must

also be written down on a piece of paper included in the shipping carton. If the unit is under war-

ranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by

contacting our customer support team on our customer support number. All packages returned to the

service department not displaying a R.A. number on the outside of the package will be returned to the

shipper.

ADJ Products, LLC - www.adj.com - Vizi Wash Z19 User Manual Page 4

ADJ Products, LLC - www.adj.com - Vizi Wash Z19 User Manual Page 5

Vizi Wash Z19 Safety Guidelines

`• DO NOT TOUCH the xture housing during operation. Turn OFF the power and allow approximately

15 minutes for the xture to cool down before servicing.

`• DO NOT shake the xture, avoid brute force when installing and/or operating the xture.

`• DO NOT operate the xture if the power cord has become frayed, crimped and/or damaged. If the

power cord is damaged, replace immediately with a new one of similar power rating.

`• DO NOT Do not attempt to remove or break o the ground prong from the electrical cord. This

prong is used to reduce the risk of electrical shock and re in case of an internal short.

`• DO NOT attempt to operate this unit, if it becomes damaged.

`• DO NOT spill water or other liquids into or on to your unit.

`• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

`• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture

`• Disconnect from main power before making any type of connection.

`• DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked.

Allow approx. 6” (15cm) between xture and other devices or a wall for proper cooling.

`• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

`• During the initial operation of this xture, a light smoke or smell may emit from the interior of the

xture. Thsi is a normal process and is caused by excess paint in the interior of the casing burning

o from the heat. This will decrease gradually over time.

`• DO NOT remove the cover under any conditions. There are no user serviceable parts inside.

`• When installing xture in a suspended enviroment, always use mounting hardware that is no less

than M10 x 25mm, and always install xture with an appropriately rated safety cable.

`• Never operate this unit when it’s cover is removed.

`• Never plug this unit in to a dimmer pack

`• During long periods of non-use, disconnect the unit’s main power.

`• Always mount this unit in safe and stable matter.

`• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

`• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 29

for cleaning details.

`• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

`• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the fixture.

C. The fixture has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a marked change in performance.

E. The fixture has fallen and/or subjected to extreme handling.

ADJ Products, LLC - www.adj.com - Vizi Wash Z19 User Manual Page 6

Vizi Wash Z19 External Light Exposure

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting moving head xtures, and lasers, which

are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ

lighting xtures, can cause severe internal damage including burning to optics, dichroic color lters,

glass and metal gobos, prisms, animation wheels, frost lters, iris, shutters, motors, belts, wiring,

discharge lamps, and LEDs.

This issue is not specic only to ADJ lighting xtures, it is a common issue with lighting xtures

from all manufacturers. Although there is no true way to fully prevent this issue from happening, the

guidelines below can prevent any potential damage from occurring if followed. Contact ADJ Service

for more details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT

SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS WHILE UNPACKING,

INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS.

DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

ENTER

ADJ Products, LLC - www.adj.com - Vizi Wash Z19 User Manual Page 7

Vizi Wash Z19 Installation

FLAMMABLE MATERIAL WARNING

Keep xture at least 5.0 feet (1.5m) away from any ammable materials,

decorations, pyrotechnics, etc.

ELECTRICAL CONNECTIONS

A qualied electrician should be used for all electrical connections

and/or installations.

CAUTIONS

• For added protection, mount the xture in areas outside walking paths, seating areas, or in are

were unauthorized personnel might reach the xture.

• Ambient operating temperature range for this xture is 14° to 104°F. (-10° to 40°C). Do not place

this lighting xture in an enviroment where the temperatures are under or above the temperatures

stated above. This will allow the xture to run at its best and help prolong the xture life.

• Before mounting the xture to any surface, make sure the installation area can hold a minimum

point load of 10 times the weight of the xture.

• Fixture installation must always be secured with a secondary safety attachment, such as an appropriate

safety cable.

• Never stand directly below the device when mounting, removing or servicing.

ADJ Products, LLC - www.adj.com - Vizi Wash Z19 User Manual Page 8

Vizi Wash Z19 Installation

CLAMP INSTALLATION

Screw one clamp via a M12 screw and nut into the Omega holder. Insert the quick-lock fasteners of

the Omega holder into the respective holes of the adjustable mounting bracket. Tighten the quick-

lock fasteners fully clockwise. Pull the safety-cable through one of the four rigging points located

on the bottom of the unit and over the trussing system or a safe xation spot. Insert the end in the

carabine and tighten the safety screw.

QUICK-LOCK

FASTENERS

SCREWS

(Not Included)

CLAMP

(Not Included)

SAFETY CABLE

RIGGING POINTS

SAFETY CABLE

RIGGING POINTS

SAFETY CABLE

RIGGING POINTS

SAFETY CABLE

RIGGING POINTS

ADJ Products, LLC - www.adj.com - Vizi Wash Z19 User Manual Page 9

Vizi Wash Z19 Installation

The Vizi Wash Z19 is fully operational in three dierent mounting positions, hanging upside-down,

mounted sideways on trussing, or set on a at level surface. Be sure this xture is kept at least

12m (40ft) away from any ammable materials (decoration etc.). Always use and install the supplied

safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp

fails (see next page). Never use the carrying handles for secondary attachment.

OVERHEAD RIGGING

When installing the unit, the trussing or area of installation must be able to hold 10 times the weight

without any deformation. When installing the unit must be secured with a secondary safety attachment,

e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or

servicing the unit.

Overhead mounting requires extensive experience, including calculating working load limits, installation

material being used, and perodic safety inspection of all installation material and unit. If you lack

these qualications, do not attempt the installation yourself.

These installaiton should be checked by a skilled person once a year.

Andere Handbücher für VIZI WASH Z19

Inhaltsverzeichnis

Andere ADJ DJ-Equipment Handbücher

ADJ

ADJ H20 IR Bedienungsanleitung

ADJ

ADJ Inno Pocket Spot Pearl Bedienungsanleitung

ADJ

ADJ ELEMENT Series Bedienungsanleitung

ADJ

ADJ XS 400 Bedienungsanleitung

ADJ

ADJ DMX OPERATOR 384 Bedienungsanleitung

ADJ

ADJ 18P HEX IP Bedienungsanleitung

ADJ

ADJ PinPoint Gobo COLOR Bedienungsanleitung

ADJ

ADJ ENCORE FR50Z Bedienungsanleitung

ADJ

ADJ PAR Z120 RGBW Bedienungsanleitung

ADJ

ADJ FS3000LED Bedienungsanleitung

ADJ

ADJ LTS COLOR Bedienungsanleitung

ADJ

ADJ 7PZ IP Bedienungsanleitung

ADJ

ADJ WIFLY PAR QA5 Bedienungsanleitung

ADJ

ADJ Inno Pocket Wash Bedienungsanleitung

ADJ

ADJ WOLFMIX WMX1 Bedienungsanleitung

ADJ

ADJ Vizi BSW 300 Bedienungsanleitung

ADJ

ADJ ENTOUR HAZE PRO Bedienungsanleitung

ADJ

ADJ stinger ii Bedienungsanleitung

ADJ

ADJ UV LED BAR20 IR Bedienungsanleitung

ADJ

ADJ Startec RAYZER Bedienungsanleitung

ADJ

ADJ Color Stand LED Bedienungsanleitung

ADJ

ADJ MB DMX II Bedienungsanleitung

ADJ

ADJ M-101HD Bedienungsanleitung

ADJ

ADJ Flat Par Tri18 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung