adpower HPM-100A Bedienungsanleitung
♦ AD pf
HPM-lOOA
User's Manual
•
�-
HPM-lOOA
Power Meter
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com
2
-Contents -
Foreword
Accessory
Before Using
Warning, Upon Having a Problem Calibration
Other Safty Precaution
Chapter 1. Get Started
Chapter 2. Part Names and Functions
2.1
Front View
2.2
Side View
2.3
LCD Screen View
2.4
Initial Setting Value
2.5
Display Font
Chapter 3. Overview, Specifications, Function
3.1
Product Introduction
3.2
General Features
3.3
General Specifications
3.4
Technical Specifications
3.5
Setting Menu Tree
3.6
Measurement Item Display
3.7
Current Range Setting
3.8 Overvoltage
·
overcurrent input warning
3.9
HOLD Function
3.10
Key Lock function
3.11
Back Light Function
3.12
Measurement of Watt-Hour(Wh)
Cautions at the time of measuring Watt-Hour(Wh)
3.13
Setting electricity charges and CO2 emissions
3.14 Green Coordinator (
Function to calculate a monthly and yearly estimates for
electricity usage, electricity charges, and CO2 emissions)
3
Chapter 4. PC Communications (RS-232C) Set Up & Circuit Diagram
4.1
RS-232 Communications Setting
4.2
How ToChange TransmissionSpeed
4.3
Circuit Diagram
Chapter 5. GUI Program & Communications Protocol Specifications
5.1
GUI Program
5.2
Support Protocol & Common Communications Specifications
5.3
How ToChange CommunicationsProtocol
5.4 AD.01 Bus Protocol Specifications
5.5 AD.02 Bus Protocol Specifications
5.6
DP Bus ProtocolSpecifications
Chapter 6. Data Logging
6.1
General specification
6.2
Time Setting Mode
6.3
Run/Stop Mode
6.4
Data Load
Chapter 7. Maintenance
How to Replace a Fuse,
Contact Information.
4
Foreword
First, we would like to sincerely thank you for your selection of AD POWER
products and wish your company every success in the future.
Before using, please make sure to completely read and understand the product, PC communication,
and GUI program manuals in order to maximize your work efficiency.
Also, please contact us if you have any problem or instrument failure upon using our
products. We promise to put our best efforts into solving the problem.
All AD POWER employees.
Accessory
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com
6
•
The maximum voltage and current is AC 250V and 15A. Exceeding its maximum
voltage and current may cause a serious damage or accident.
•
Measuring the load in the range from AC 10A to 15A (less than 30 seconds on each
measuring,) please maintain at least 10 minute intervals in-between measurements.
Any
electric current less than 10A can be measured for a long period.
•
If this equipment is used more than 30 seconds when measuring an electric current
between10A~ 15A,"OL"willappear on thedisplay andanalarm will soundto warn the
user and avoid a danger.
When it occurs, wait for 10 minutes and resume the measurement.
•
The power supply voltage of the equipment should not exceed 90~250V (SMPS)
before turning on.
•
If you notice a smoke, smell, or sound while using the equipment, immediately turn off
the power and consult our service center or head office.
•
This equipment should be used in a temperature and humidity of less than 10℃
~ 50℃/RH65% and kept away from a wet towel, dust, and damp place.
•
A strong electronic or magnetic field can cause an error in measurement.
•
Avoid a hazardous gas and try not to step on the cable nor twist it.
•
For accurate measurement, turn on the equipment and let it warm up for more than 5
minutes.
•
For accurate measurement, beware of overheating of the equipment and provide a
sufficient ventilation space.
•
When moving this equipment, please use its original packing materials and boxes. If
not, use a plastic bag to seal it from external moisture and lay more than 20mm of a
shock absorbent on the bottom before packaging.
•
If the back cover is not closed completely, never use the equipment.
•
Makesurethatthesupplyvoltage(sourcevoltage)andthe voltage of theappliance that
is to be measured are the same.
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com
8
9.
Watthourstart/stopbutton :watthouroperationstart/stopinthewatthoursmode (LCD
displays "ENERGY")
※For the data logging equipment, it is used to start/stop logging.
10.
CO2 setting value change button :Electricity charges andCO2 emissionunitsetting (in
the watt-hourmode)
※In all other modes, press and hold it to enter the setting mode.
11.
Receptacle : Secondary receptacle (plug in the appliance to be measured)
■
All buttons related to watt hour can be accessed in the watt-hour mode.
2-2
Side View
1.
RS 232 port : Communication port (RS232C/ D-SUB 9Pin)
2.
2 stage folding stand : Folding stand (2 stages)
3.
Safety rubber cap : Safety rubber cap (safety cover - please uncover the cap before
measuring)
9
2-3
LCD Screen View
1)
Data logging indicator: it blinks when data logging
2)
Input power indicator: AC only
3)
Pause indicator: pause displaying measurement / It blinks when the Key Lock is activated
4)
Communication indicator: PC communication indicator
5)
Measuring process indicator: when calculating watt hour, it displays "ENERGY"
6)
Frequency indicator: it displays the measured frequency
7)
It displays power factor, CO2 emissions, electricity charge unit
8)
It displays the measured reactive power unit
9)
It displays the measured active power and watt hour unit
10)
Current indication: it displays the current of the appliance
11)
Voltage indicator: it displays the voltage of the appliance
12)
Autorangeindicator:itoperatestherange automatically
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com
10
2.4
Initial Setting Value
1)
Communication protocol: AD.02 (for Wattman Viewer)
2)
Communication speed: 9600bps
3)
Electric power integration time: 1hour
4)
Power rate: 188won (per kWh)/ varies with country.
5)
Generation of carbon dioxide (Co2): 0.425kg (per kWh)
6)
Initial value related to data logging
-
Data logging storage item: Voltage(V), Current(A), Active power(W), Electric
power(Wh), Power factor(PF), Frequency(Hz),
-
Logging Interval: 1second
-
Data logging mode: Run/Stop mode (No setting time)
2.5
Display font
Inhaltsverzeichnis
Andere adpower Messgerät Handbücher
