ADTRAN DSU IQ Bedienungsanleitung
ADTRAN DSU IQ Remote Configuration Capability
Introduction
IntroductionIntroduction
Introduction
Remote configuration is a very useful feature of the ADTRAN DSU IQ. Using a VT 100
terminal session and local unit, a user may configure the units at remote sites. This
process is non-disruptive to customer data. For example, in Figure 1 the user could
remotely configure the DSU IQ at remote site #1 or remote site #2 from the host DSU IQ.
In addition, either remote DSU IQ could remotely configure the host DSU IQ. It should
be noted that due to the fact that there is not a virtual circuit connecting the two remote
sites, neither remote site DSU IQ could remotely configure the other remote site DSU IQ.
The host site communicates with remote site #1 via DLCI 16 and remote site #2 via
DLCI 17. Remote site #1 sends data to the host site via DLCI 18 and remote site #2 sends
data to the host site via DLCI 19.
Figure 1
Figure 1Figure 1
Figure 1
Directions for the Remote Configuration Process
Directions for the Remote Configuration ProcessDirections for the Remote Configuration Process
Directions for the Remote Configuration Process
1. Connect the straight-through RJ45 silver satin cable provided by ADTRAN to the
control port of the unit. Connect the other end of the cable to the RJ45 to DB25
adapter provided. Only use the ADTRAN adapter part number 3196.ADPT005.
Other vendor adapters will not work. Connect the DB25 end of the adapter to the
COM port of your computer. If your computer COM port is a DB9, a DB9 to
DB25 adapter will be necessary.
2. Open a terminal emulation program using the parameters 9600 bps, 8 data bits, 1
stop bit, and no parity. At this point, you should see a blank screen. Press return
several times and the login screen shown in Figure 2 will appear.
LOGIN MENU ADTRAN DSUIQ
LOCAL
______________________________________________________________________________
1 - LOCAL LOGIN
2 - REMOTE LOGIN
______________________________________________________________________________
ENTER SELECTION ->
Figure 2
Figure 2Figure 2
Figure 2
3. Choose 2 for remote login and press RETURN. The login screen shown in Figure
3 will appear.
REMOTE LOGIN ADTRAN DSUIQ
LOCAL
______________________________________________________________________________
1 - REMOTE DLCI 0
2 - BEGIN REMOTE SESSION
______________________________________________________________________________
ENTER SELECTION ->
Figure 3
Figure 3Figure 3
Figure 3
4. Choose 1 for remote DLCI and enter the remote DLCI. The remote DLCI is the
DLCI on which the data is sent to the remote site, not the DLCI of the remote site.
Using Figure 1, when the user at the host site is remotely configuring the DSU IQ
at remote site 1, the remote DLCI would be 16. When the user at remote site #1 is
remotely configuring the host DSU IQ, the remote DLCI would be 18. Enter the
remote DLCI, select 2 for begin remote session and press ENTER. The screen in
Figure 4 will appear.
------------------------------------------------------------------------------
Any key to continue...
------------------------------------------------------------------------------
______________________________________________________________________________
ENTER SELECTION ->
Figure 4
Figure 4Figure 4
Figure 4
5. Press any key and the screen shown in Figure 5 will appear.
------------------------------------------------------------------------------
Enter password:
------------------------------------------------------------------------------
Figure 5
Figure 5Figure 5
Figure 5
6. The default password is ADTRAN. It is not case sensitive. The screen shown in
Figure 6 will then appear.
MAIN MENU ADTRAN DSUIQ
REMOTE
______________________________________________________________________________
1 - CONFIGURATION
2 - VIEW STATISTICS
3 - TEST
4 - LOGOUT
______________________________________________________________________________
ENTER SELECTION ->
Figure 6
Figure 6Figure 6
Figure 6
7. Notice the change in the upper right hand corner from local to remote. You are
now configuring the remote unit.
Troubleshooting the Remote Configuration Process
Troubleshooting the Remote Configuration ProcessTroubleshooting the Remote Configuration Process
Troubleshooting the Remote Configuration Process
1. If you are unable to see the initial login screen, there may be a physical
connection problem.
o
Verify that the correct computer COM port is being used. This may be
accomplished by connecting to another device, such as a modem.
o
Verify the proper ADTRAN RJ45-DB25 adapter is connected. The
adapter is labeled with ADTRAN part number 3196.ADPT005.
o
Verify that the RJ-45 silver satin cable is pinned out with all eight pins
straight through the cable. Orient the two RJ-45 connectors with the tab
down and the gold pins pointing away from the user. The same color wire
should be present in each position, left-to-right, on both RJ-45 connectors
as shown in Figure 7.
Figure 7
Figure 7 Figure 7
Figure 7
o
Verify that the RJ-45 silver satin cable is plugged into the control port on
the back of the ADTRAN DSU IQ.
2. If you are able to see the initial login screen but the remote configuration session
fails, the screen shown in Figure 8 will continue to be displayed after pressing a
key on the computer.
------------------------------------------------------------------------------
Any key to continue...
------------------------------------------------------------------------------
______________________________________________________________________________
ENTER SELECTION ->
Figure 8
Figure 8Figure 8
Figure 8
To return to the Login screen, press Ctrl L twice. This should disconnect the
remote login session and bring up the initial screen of the local unit as shown in
Figure 9.
LOGIN MENU ADTRAN DSUIQ
LOCAL
______________________________________________________________________________
1 - LOCAL LOGIN
2 - REMOTE LOGIN
______________________________________________________________________________
ENTER SELECTION ->
Figure 9
Figure 9Figure 9
Figure 9
There are four possible reasons that could cause a remote configuration session to
fail:
•
The remote DSU IQ is not powered on or not connected to the frame relay
circuit.
•
There is a problem with the frame relay circuit.
•
The local or remote DSU IQ is in alarm.
•
An incorrect remote DLCI was used. To verify that the correct DLCI was
chosen, from the VT 100 terminal session, select Local Login to connect
to the local unit. From the main menu, select View Statistics, DLCI List,
and the screen shown in Figure 10 will appear.
ADTRAN DSUIQ VIEW DLCI STATISTICS LOCAL
------------------ Frames ------------------ ------- Bytes -------
DLCI In Out FECN BECN DE In Out
18 A 11 10 0 0 11 905 90
UNKNOWN 0 0 0 0
INACTIVE 0 0 0 0
SIGNAL 0 0 0 0
ESC = Prev Menu +,- = Page
______________________________________________________________________________
ENTER SELECTION ->
Figure 10
Figure 10Figure 10
Figure 10
This screen shows DLCI 18 is active (A). This tells the user that DLCI 18 is being
advertised by the frame relay switch as valid for this site. If the user entered any number
other than 18, that DLCI was incorrect and therefore caused the remote configuration
failure. The DLCI must be active in order for the remote configuration to work. If the
status is I for inactive, the customer should contact the telephone company and report that
their DLCI is inactive.
If you experience any problems using your ADTRAN product, please contact ADTRAN
Technical Support @ 888-423-8726
DISCLAIMER
ADTRAN provides the foregoing application description solely for the reader's
consideration and study, and without any representation or suggestion that the foregoing
application is or may be free from claims of third parties for infringement of intellectual
property rights, including but not limited to, direct and contributory infringement as well
as for active inducement to infringe. In addition, the reader's attention is drawn to the
following disclaimer with regard to the reader's use of the foregoing material in products
and/or systems. That is:
ADTRAN SPECIFICALLY DISCLAIMS ALL WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO, MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ADTRAN BE
LIABLE FOR ANY LOSS OR DAMAGE, AND FOR PERSONAL INJURY,
INCLUDING BUT NOT LIMITED TO, COMPENSATORY, SPECIAL,
INCIDENTAL, CONSEQUENTIAL, OR OTHER DAMAGES.
Andere Handbücher für DSU IQ
1
Inhaltsverzeichnis
Andere ADTRAN Netzwerk-Hardware Handbücher
ADTRAN
ADTRAN ENHANCED PSD 239 H2R Bedienungsanleitung
ADTRAN
ADTRAN 1442823F1 Bedienungsanleitung
ADTRAN
ADTRAN DSX 1 Bedienungsanleitung
ADTRAN
ADTRAN HTU-C Bedienungsanleitung
ADTRAN
ADTRAN SLC-5 U-BR1TE III Bedienungsanleitung
ADTRAN
ADTRAN DDS T200 Bedienungsanleitung
ADTRAN
ADTRAN 1200184L1 Bedienungsanleitung
ADTRAN
ADTRAN ACT 1900 Bedienungsanleitung
ADTRAN
ADTRAN 1200130L1 Bedienungsanleitung
ADTRAN
ADTRAN 1442890G2 Bedienungsanleitung
ADTRAN
ADTRAN ISU 512 Bedienungsanleitung
ADTRAN
ADTRAN NetVanta 2000 Series Bedienungsanleitung
ADTRAN
ADTRAN DSU IV ESP Bedienungsanleitung
ADTRAN
ADTRAN Quad T1 IMA Bedienungsanleitung
ADTRAN
ADTRAN 1200221L1 Bedienungsanleitung
ADTRAN
ADTRAN HDSL4 Bedienungsanleitung
ADTRAN
ADTRAN XFP Bedienungsanleitung
ADTRAN
ADTRAN Total Access 1500 Total Reach DDS-DP Produkthandbuch
ADTRAN
ADTRAN NetVanta 873 Bedienungsanleitung
ADTRAN
ADTRAN 1442120G1 Bedienungsanleitung
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
