ADTRAN DSU IV ESP Bedienungsanleitung

DSU IV ESP

Data Service Unit with Embedded SNMP

USER MANUAL

Part Number Version

1204011L1 DSU IV ESP

1204001L1 ESP 4-wire Switched 56 DBU Card

1204002L1 ESP V.34 DBU Card

1204004L1 ESP ISDN DBU Card

1204005L1 ESP Ethernet Card

61204.011L1-1A

May 1997

Trademark Information:

Hayes is a registered trademark of Hayes Microcomputer Products, Inc.

Openview is a registered trademark of Hewlett-Packard Company.

SunNet Manager is a registered trademark of Sun Microsystems, Inc.

Netview is a registered trademark of IBM.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

Phone: (205) 963-8000

Printed in USA.

ABOUT THIS MANUAL

This manual is arranged so you can quickly and easily find the information you

need. The following is an overview of the contents of this manual:

• Chapter 1, Introduction, familiarizes you with DDS, Switched 56, SNMP, and

TELNET. This chapter also includes DSU IV highlights and describes the options

that may be purchased for use with the DSU.

• Chapter 2, Installation, describes the DSU connectors (pin assignments are given in

Appendix A) and provides an installation diagram.

• Chapter 3, Operation, explains how to operate your DSU using either the front

panel or a VT 100 terminal interface.

• Chapter 4, Applications, provides examples of some common DSU applications,

including network diagrams.

• Chapter 5, Configuration Overview, explains how to access the DSU configuration

menu, including information on the different configuration methods. This chapter

also provides a front panel menu tree.

• Chapters 6 through 11 provide brief explanations for selections made in the Con-

figuration menus. These chapters are based on the front panel menu branches of

the Configuration menu: Network Options, DTE Options, Test Options, Dial

Options, Management, and Utilities.

• Chapter 12, Testing and Troubleshooting, describes the testing options available

with the DSU IV and gives troubleshooting information.

• Chapter 13, Activating Dial Functions, describes the Dial options available from the

Main menu.

• Chapter 14, Viewing Status Information, provides information on the status menus

available for the base unit as well as the DBU cards.

• Appendix A provides pinouts for the connectors of the DSU and the DBU and

Ethernet cards.

• Appendix B shows the AT commands available for the DSU.

• Appendix C describes the terminal menu interface (accessed through a VT 100

terminal or a TELNET session).

• Appendix D provides information on the unit's configuration profiles.

• Appendix E contains a DSU to modem interconnect diagram for a modem tail

circuit application.

• Appendix F contains product specifications.

Notes provide additional useful information.

Cautions signify information that could prevent service interruption.

Warnings provide information that could prevent damage to the

equipment or endangerment to human life.

FCC regulations require that the following information be provided in this manual:

1. This equipment complies with Part 68 of the FCC rules. On the bottom of the equipment

housing is a label that shows the FCC registration number and ringer equivalence number

(REN) for this equipment. If requested, provide this information to the telephone company.

2. If this equipment causes harm to the telephone network, the telephone company may temporarily

discontinue service. If possible, advance notification is given; otherwise, notification is given

as soon as possible. The telephone company will advise the customer of the right to file a

complaint with the FCC.

3. The telephone company may make changes in its facilities, equipment, operations, or

procedures that could affect the proper operation of this equipment; advance notification and

the opportunity to maintain uninterrupted service are given.

4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and

warranty information. The telephone company may require this equipment to be

disconnected from the network until the problem is corrected, or it is certain the equipment is

not malfunctioning.

5. This unit contains no user-serviceable parts.

6. An FCC compliant telephone cord with a modular plug is provided with this equipment. In

addition, an FCC compliant cable appropriate for the dial backup option ordered is provided

with this equipment. This equipment is designed to be connected to the telephone network or

premises wiring using an FCC compatible modular jack, which is Part 68 compliant.

7. The following information may be required when applying to the local telephone company for

leased line facilities:

Service Digital Facility Service Order Network

Type Interface Code Code Jacks

2.4 kbps Digital Interface 04DU5-24 6.0F RJ-48S

4.8 kbps Digital Interface 04DU5-48 6.0F RJ-48S

9.6 kbps Digital Interface 04DU5-96 6.0F RJ-48S

19.2 kbps Digital Interface 04DU5-19 6.0F RJ-48S

38.4 kbps Digital Interface 04DU5-38 6.0F RJ-48S

56 kbps Digital Interface 04DU5-56 6.0F RJ-48S

64 kbps Digital Interface 04DU5-64 6.0F RJ-48S

8. The following information may be required when applying to the local telephone company for

a dial-up line for the V.34:

Service REN FIC USOC

Type

Loop Start (V.34) 0.8B/0.4A 02LS2 RJ-11C

9. The REN is useful in determining the quantity of devices you may connect to your telephone

line and still have all of those devices ring when your number is called. In most areas, the sum

of the RENs of all devices should not exceed five. To be certain of the number of devices you

may connect to your line as determined by the REN, call your telephone company to

determine the maximum REN for your calling area.

10.This equipment may not be used on coin service provided by the telephone company.

Connection to party lines is subject to state tariffs. (Contact your state public utility

commission or corporation commission for information.)

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio frequencies. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to correct the interfer-

ence at his own expense.

Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.

Change or modifications to this unit not expressly approved by the

party responsible for compliance could void the user's authority to

operate the equipment.

CANADIAN EMISSIONS REQUIREMENTS

This digital apparatus does not exceed the Class A limits for radio noise emissions

from digital apparatus as set out in the interference-causing equipment standard

entitled "Digital Apparatus," ICES-003 of the Department of Communications.

Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux

appareils numeriques de Class A prescrites dans la norme sur le materiel brouilleur:

"Appareils Numeriques," NMB-003 edictee par le ministre des Communications.

CANADIAN EQUIPMENT LIMITATIONS

Notice: The Canadian Industry and Science Canada label identifies certified

equipment. This certification means that the equipment meets certain telecom-

munications network protective, operational, and safety requirements. The

Department does not guarantee the equipment will operate to the user's satisfac-

tion.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The equip-

ment must also be installed using an acceptable method of connection. In some

cases, the company's inside wiring associated with a single line individual

service may be extended by means of a certified connector assembly (telephone

extension cord). The customer should be aware that compliance with the above

conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian

maintenance facility designated by the supplier. Any repairs or alterations made

by the user to this equipment, or equipment malfunctions, may give the telecom-

munications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connec-

tions of the power utility, telephone lines and internal metallic water pipe

system, if present, are connected together. This precaution may be particularly

important in rural areas.

Caution: Users should not attempt to make such connections themselves, but

should contact the appropriate electric inspection authority, or an electrician, as

appropriate.

The Load Number (LN) assigned to each terminal device denotes the percentage

of the total load to be connected to a telephone loop which is used by the device,

to prevent overloading. The termination on a loop may consist of any combina-

tion of devices subject only to the requirement that the total of the Load Num-

bers of all devices does not exceed 100.

ISDN Service Ordering Information for the ADTRAN DSU IV ESP With ISDN Dial

Backup

For ADTRAN DSU IV ESP ISDN applications, the following guide can be used as

an aid in ordering basic ISDN service from your local telephone company. The

ADTRAN DSU IV ESP ISDN includes NT1 and Terminal adapter functionality and

supports data rates up to 64 kbps.

Request an ISDN Basic Rate Interface (BRI) line with the following features:

U-interface reference point

2B1Q line coding

1B+D Service (supports up to 64 kbps)

The DSU IV ESP ISDN supports the following switch types and software

protocols:

AT&T 5ESS Custom, 5E6 and later software, National ISDN-1

NT1 DMS-100 BCS-32 and later software (Pvc1), National ISDN-1 (Pvc2)

Siemens EWSD National ISDN-1

Request that the ISDN line allocate one DYNAMIC Terminal Endpoint Identifier

(TEI) for the number.

For service offered from an AT&T 5ESS, request a point-to-point line with the

following features:

Feature: Value

B1 Service: On Demand (DMD)

Data Line Class: Point-to-Point

Maximum B Channels: 1 (1B+D)

Circuit Switched Data (CSD) Bearer Channels: Any

Number of CSD Calls: 1 (1B+D)

Terminal Type: Type A

Turn the Following Features Off:

Packet Mode Data

Multi-line Hunt

Multiple Call Appearances

Electronic Key Telephone Sets (EKTS)

Shared Dictionary Numbers

Accept Special Type of Number

Intercom Groups

Network Resource Selector (Modem Pools)

Message Waiting

Hunting

InterLata Competition

For service offered from a Northern Telecom DMS-100, request a Point-to-Point

Multi-Point line with the following features:

Line Type: Basic Rate, Functional

Electronic Key Telephone Sets (EKTS): No

Call Appearance Handling (CACH): No

Non-Initializing Terminal: No

Circuit Switched Service: Yes

Packet Switched Service: No

TEI: Dynamic

Bearer Service: Circuit Switched voice and data permitted on any B channel (packet mode

data not permitted)

Table of Contents

Andere Handbücher für DSU IV ESP

Dieses Handbuch passt für folgende Modelle

Andere ADTRAN Netzwerk-Hardware Handbücher

ADTRAN

ADTRAN NetVanta SHDSL Network Interface Module Bedienungsanleitung

ADTRAN

ADTRAN 1442704PG1 Bedienungsanleitung

ADTRAN

ADTRAN Total Reach DDS-R Bedienungsanleitung

ADTRAN

ADTRAN 1203060L1 Bedienungsanleitung

ADTRAN

ADTRAN Total Access 372E Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 873 Bedienungsanleitung

ADTRAN

ADTRAN 414 RG Bedienungsanleitung

ADTRAN

ADTRAN Total Access 300 Series Bedienungsanleitung

ADTRAN

ADTRAN TSU LT Bedienungsanleitung

ADTRAN

ADTRAN Quad T1 IMA Bedienungsanleitung

ADTRAN

ADTRAN 24-Port DSLAM Access Module IADSL Module Bedienungsanleitung

ADTRAN

ADTRAN DS3 MX Bedienungsanleitung

ADTRAN

ADTRAN P/N 1204011L1 Service-Handbuch

ADTRAN

ADTRAN Dial Backup Interface Module 1204006L2 Bedienungsanleitung

ADTRAN

ADTRAN T1 Nx64 HTU-R Bedienungsanleitung

ADTRAN

ADTRAN Total Access 300 Series Produkthandbuch

ADTRAN

ADTRAN Total Access 300 Series Bedienungsanleitung

ADTRAN

ADTRAN Total Access DSLAM 16-Port ADSL2+ Access Module... Bedienungsanleitung

ADTRAN

ADTRAN 602 Bedienungsanleitung

ADTRAN

ADTRAN jobAid+ 1200482G1 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta Series Bedienungsanleitung

ADTRAN

ADTRAN JOBAID Total Access 838 Bedienungsanleitung

ADTRAN

ADTRAN 401 1 GE Micro ONT Bedienungsanleitung

ADTRAN

ADTRAN XFP Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung