ADTRAN NetVanta 900 Series Handbuch

NetVanta 950 IAD

Hardware Installation Guide

1200785L1 NetVanta 900 Series AC Power Supply

1200786L1 NetVanta 900 Series AC Chassis

1200788L1 NetVanta 950 IAD System Controller

1200791L1 NetVanta 900 Series Octal FXS Module

1200792L1 NetVanta 900 Series Octal FXO Module

1200793L1 NetVanta 900 Series Octal Ethernet Switch Module

1200798L1 NetVanta 950 IAD T1/V.35 Expansion Module

61200788L1-34B

July 2004

Hardware Installation Guide NetVanta 950 IAD

Trademarks

Any brand names and product names included in this manual are trademarks, registered trademarks, or

trade names of their respective holders.

To the Holder of this Manual

The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change

the contents without prior notice.

In no event will ADTRAN be liable for any special, incidental, or consequential damages or for

commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

Phone: (256) 963-8000

www.adtran.com

Printed in U.S.A.

NetVanta 950 IAD Hardware Installation Guide

Conventions

Safety Instructions

When using your communications equipment, please follow these basic safety precautions to reduce the

risk of fire, electrical shock, or personal injury:

1. Do not use this product near water such as a bathtub, wash bowl, kitchen sink, laundry tub, in a

wet basement, or near a swimming pool.

2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote

risk of shock from lightning.

3. Do not use a telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of

batteries in a fire. They may explode. Check with local codes for special disposal instructions.

Save These Important Safety Instructions

Notes provide additional useful information.

Cautions signify information that could prevent service interruption.

Warnings provide information that could prevent damage to the equipment or

endangerment to human life.

Hardware Installation Guide NetVanta 950 IAD

Affidavit Requirements for Connection to Digital Services

• An affidavit is required to be given to the telephone company whenever digital terminal equipment

(DTE) without encoded analog content and billing protection is used to transmit digital signals

containing encoded analog content intended for eventual conversion into voiceband analog signals and

transmitted on the network.

• The affidavit shall affirm that either no encoded analog content or billing information is being

transmitted or that the output of the device meets Part 68 encoded analog content or billing protection

specifications.

• The end user/customer will be responsible for filing an affidavit with the local exchange carrier when

connecting unprotected customer premise equipment (CPE) to 1.544 Mbps or subrate digital services.

• Until such time as subrate DTE is registered for voice applications, the affidavit requirement for subrate

services is waived.

NetVanta 950 IAD Hardware Installation Guide

Affidavit for Connection of Customer Premises Equipment

to 1.544 Mbps and/or Subrate Digital Services

For the work to be performed in the certified territory of ___________________ (telco name)

State of ________________

County of ________________

I, _______________________ (name), ____________________________________ (business address),

____________________ (telephone number) being duly sworn, state:

I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544 Mbps and/or

________ subrate digital services. The terminal equipment to be connected complies with Part 68 of the FCC rules except

for the encoded analog content and billing protection specifications. With respect to encoded analog content and billing

protection:

( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the digital CPE with respect to

analog content and encoded billing protection information continuously complies with Part 68 of the FCC Rules and

Regulations.

( ) The digital CPE does not transmit digital signals containing encoded analog content or billing information which is intended

to be decoded within the telecommunications network.

( ) The encoded analog content and billing protection is factory set and is not under the control of the customer.

I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, maintenance, and

adjustment of the encoded analog content and billing information has (have) been trained to perform these functions by

successfully having completed one of the following (check appropriate statements):

( ) A. A training course provided by the manufacturer/grantee of the equipment used to encode analog signals; or

( ) B. A training course provided by the customer or authorized representative, using training materials and instructions

provided by the manufacturer/grantee of the equipment used to encode analog signals; or

( ) C. An independent training course (e.g., trade school or technical institution) recognized by the manufacturer/grantee of the

equipment used to encode analog signals; or

( ) D. In lieu of the preceding training requirements, the operator(s)/maintainer(s) is (are) under the control of a supervisor

trained in accordance with _________ (circle one) above.

I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate compliance with the

information as provided in the preceding paragraph, if so requested.

_________________________________Signature

_________________________________Title

_________________________________ Date

Transcribed and sworn to before me

This ________ day of _______________, _______

_________________________________

Notary Public

My commission expires:

_________________________________

Hardware Installation Guide NetVanta 950 IAD

FCC regulations require that the following information be provided in this manual:

1. This equipment complies with Part 68 of FCC rules and requirements adopted by ACTA. Each

registered interface has a label that contains, among other information, a product identifier in the

format US:AAAEQ##TXXXX. If requested, provide this information to the telephone company.

2. If this equipment causes harm to the telephone network, the telephone company may temporarily

discontinue service. If possible, advance notification is given; otherwise, notification is given as

soon as possible. The telephone company will advise the customer of the right to file a complaint

with the FCC.

3. The telephone company may make changes in its facilities, equipment, operations, or procedures

that could effect the proper operation of this equipment. Advance notification and the opportunity

to maintain uninterrupted service are given.

4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty

information. The telephone company may require this equipment to be disconnected from the

network until the problem is corrected or it is certain the equipment is not malfunctioning.

5. This unit contains no user-serviceable parts.

6. This equipment is designed to connect to the telephone network or premises wiring using an

FCC-compatible modular jack, which is compliant with Part 68 and requirements adopted by

ACTA.

7. The following information may be required when applying to the local telephone company for

leased line facilities:

8. The REN is useful in determining the quantity of devices you may connect to your telephone line

and still have all of those devices ring when your number is called. In most areas, the sum of the

RENs of all devices should not exceed five. To be certain of the number of devices you may

connect to your line as determined by the REN, call your telephone company to determine the

maximum REN for your calling area.

9. This equipment may not be used on coin service provided by the telephone company. Connection

to party lines is subject to state tariffs. Contact your state public utility commission or corporation

commission for information.

Part Number

Registration

Number Service Type REN/SOC FIC USOC

1200786L1 US: HDCDFNAN1200788L1 1.544 Mbps - SF

1.544 Mbps - SF and B8ZS

1.544 Mbps - ESF

1.544 Mbps - ESF and B8ZS

6.0N

04DU9-BN

04DU9-DN

04DU9-1KN

04DU9-1SN

RJ-48C

1200798L1 US: HDCDENAN1200798L1

1200792L1 US: HDCKX03B1200792L1 Analog Loop Start/Ground

Start

0.3B/9.0F 02LS2/02GS2 RJ-11C

NetVanta 950 IAD Hardware Installation Guide

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Canadian Emissions Requirements

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus

as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the

Department of Communications.

Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques

de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee

par le ministre des Communications.

Industry Canada Compliance Information

Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the

“IC:” in front of the certification/registration number) signifies that the Industry Canada technical

specifications were met.

Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the

documentation or on the product labeling/markings. The REN assigned to each terminal device indicates

the maximum number of terminals that can be connected to a telephone interface. The termination on an

interface may consist of any combination of devices subject only to the requirement that the sum of the

RENs of all the devices should not exceed five (5).

Changes or modifications to this unit not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

Hardware Installation Guide NetVanta 950 IAD

Product Warranty

ADTRAN will repair and return this product within the warranty period if it does not meet its published

specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty.

Product Registration

Registering your product helps ensure complete customer satisfaction. Please take time to register your

products on line at www.adtran.com. Click Service and Support on the top of the page, and then click

Product Registration under Support.

Customer Service, Product Support Information, and Training

ADTRAN will repair or return this product within the warranty period if it does not meet its published

specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty.

A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service,

RMA requests, training, or more information, use the contact information given below.

Repair and Return

If you determine that a repair is needed, please contact our Customer and Product Service (CaPS)

department to have an RMA number issued. CaPS should also be contacted to obtain information

regarding equipment currently in house or possible fees associated with repair.

Identify the RMA number clearly on the package (below address), and return to the following address:

Pre-Sales Inquiries and Applications Support

Your reseller should serve as the first point of contact for support. If additional pre-sales support is needed,

the ADTRAN Support web site provides a variety of support services such as a searchable knowledge

base, latest product documentation, application briefs, case studies, and a link to submit a question to an

Applications Engineer. All of this, and more, is available at:

When needed, further pre-sales assistance is available by calling our Applications Engineering

Department.

CaPS Department (256) 963-8722

ADTRAN Customer and Product Service

901 Explorer Blvd. (East Tower)

Huntsville, Alabama 35806

RMA # _____________

http://support.adtran.com

Applications Engineering (800) 615-1176

NetVanta 950 IAD Hardware Installation Guide

Post-Sale Support

Your reseller should serve as the first point of contact for support. If additional support is needed, the

ADTRAN Support web site provides a variety of support services such as a searchable knowledge base,

updated firmware releases, latest product documentation, service request ticket generation and

trouble-shooting tools. All of this, and more, is available at:

When needed, further post-sales assistance is available by calling our Technical Support Center. Please

have your unit serial number available when you call.

Installation and Maintenance Support

The ADTRAN Custom Extended Services (ACES) program offers multiple types and levels of installation

and maintenance services which allow you to choose the kind of assistance you need. This support is

available at:

For questions, call the ACES Help Desk.

Training

The Enterprise Network (EN) Technical Training Department offers training on our most popular products.

These courses include overviews on product features and functions while covering applications of

ADTRAN's product lines. ADTRAN provides a variety of training options, including customized training

and courses taught at our facilities or at your site. For more information about training, please contact your

Territory Manager or the Enterprise Training Coordinator.

http://support.adtran.com

Technical Support (888) 4ADTRAN

http://www.adtran.com/aces

ACES Help Desk (888) 874-ACES (2237)

Training Phone (800) 615-1176, ext. 7500

Training Fax (256) 963-6700

Training Email training@adtran.com

Hardware Installation Guide NetVanta 950 IAD

Andere Handbücher für NetVanta 900 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ADTRAN Netzwerk-Hardware Handbücher

ADTRAN

ADTRAN D4-n x 56 DSU DP Bedienungsanleitung

ADTRAN

ADTRAN 6540 Produkthandbuch

ADTRAN

ADTRAN NetVanta 818 Bedienungsanleitung

ADTRAN

ADTRAN Total Reach DDS-DP 5 Series Bedienungsanleitung

ADTRAN

ADTRAN TSU 120 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta E1/FE1 + G.703 Network Interface... Bedienungsanleitung

ADTRAN

ADTRAN QFO-C Bedienungsanleitung

ADTRAN

ADTRAN TSU LT Bedienungsanleitung

ADTRAN

ADTRAN BR1 Bedienungsanleitung

ADTRAN

ADTRAN Total Access 1500 Total Reach DDS-DP Bedienungsanleitung

ADTRAN

ADTRAN 1200630L1 Bedienungsanleitung

ADTRAN

ADTRAN DSU IQ Bedienungsanleitung

ADTRAN

ADTRAN NxT1 HSSI/V-35 Bedienungsanleitung

ADTRAN

ADTRAN Express 6500 Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta Series Bedienungsanleitung

ADTRAN

ADTRAN SFP Series Bedienungsanleitung

ADTRAN

ADTRAN Express 3100 Bedienungsanleitung

ADTRAN

ADTRAN Total Access 301 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 4660 Bedienungsanleitung

ADTRAN

ADTRAN eSBC Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 8044M Bedienungsanleitung

ADTRAN

ADTRAN TRACER 64 0 Series Bedienungsanleitung

ADTRAN

ADTRAN 1700900F2 Bedienungsanleitung

ADTRAN

ADTRAN 1200864L1 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung