ADTRAN NetVanta 7000 Series Bedienungsanleitung

Configuring the

NetVanta 7000 Series

for the IP 700 Series Phones

Quick Configuration Guide 61200770E1-42C November 2008

This quick configuration guide provides assistance in configuring the NetVanta 7000 Series

product to operate with IP 700 Series phones. These instructions are only applicable to

NetVanta 7000 Series products running AOS 14 firmware or newer. It is assumed that the

NetVanta 7000 Series product has been configured as instructed in the quick start guide provided

with your unit and hardware installation guide provided on the AOS Documentation CD. It also

assumes that the IP 700 Series phones have been assembled per the instructions in the

quick start guide provided with them.

The following sections provide step-by-step instructions for:

• Configuring the DHCP server settings

• Creating SIP accounts

• Uploading configuration files

• Phone setup

Enabling the Dynamic Host Configuration Protocol (DHCP) server on the NetVanta can be

accomplished using either the command line interface (CLI) or the Web-based graphical user

interface (GUI). Both sets of instructions are provided below. Choose the method that best suits

your situation.

The IP 700 Series phone uses site-specific Option 157 to provide the following information to the

phones:

TftpServers=0.0.0.0

FtpServers=10.10.20.1:/ADTRAN

FtpLogin=polycomftp

FtpPassword=password

Layer2Tagging=True

VlanID=2

Configuring the DHCP Server Settings

Option 157 must be set on both the LAN_pool and the VoIP_pool to direct the

phones to the correct boot server.

If the voice virtual local area network (VLAN) address has been changed to

something other than 10.10.20.1 for a particular NetVanta server, you will need to

adjust the FtpServers address in the commands above.

Using the CLI to Configure the DHCP Server

1. Access the CLI for your server. If you are not familiar with using the CLI, review the AOS

Command Reference Guide available on the AOS Documentation CD shipped with your

NetVanta unit or from www.adtran.com.

2. Issue the following commands to configure the DHCP settings. It is necessary to execute an

ip ftp server default-filesystem cflash command to ensure that the FTP server is accessing

the CompactFlash®. This is included in the following commands:

>enable

#configure terminal

(config)#ip ftp server default-filesystem cflash

(config)#ip dhcp-server pool LAN_pool

(config)#option 157 ascii TftpServers=0.0.0.0, FtpServers=10.10.20.1:/ADTRAN,

FtpLogin=polycomftp, FtpPassword=password, Layer2Tagging=True, VlanID=2

(config)#ip dhcp-server pool VoIP_pool

(config-dhcp)#option 157 ascii TftpServers=0.0.0.0, FtpServers=10.10.20.1:/ADTRAN,

FtpLogin=polycomftp, FtpPassword=password, Layer2Tagging=True, VlanID=2

(config-dhcp)#exit

3. Enter the copy running-config startup-config command to save the changes made to the

configuration. This copies your changes to the unit’s nonvolatile random access memory

(NVRAM). Once the save is complete, the changes are retained even if the unit is shut down,

or suffers a power outage.

Using the GUI to Configure the DHCP Server

The GUI is an online configuration tool that allows you to easily configure and view the main

settings, as well as the status of your system.

1. Connect the NetVanta 7000 Series unit to your network using the first Ethernet port (eth 0/1)

on the front panel of the unit. The NetVanta 7000 Series supports auto MDI-MDIX crossover;

therefore, a straight-through cable can be used for this connection.

2. Configure your PC to obtain an IP address automatically via DHCP, or change the IP address

of your PC to 10.10.10.2. The default address for the NetVanta 7000 Series is 10.10.10.1.

If the default FTP Login (polycomftp) and FTP Password (password) have been

changed to something other than the system defaults, you will need to adjust the

FtpLogin and FtpPassword settings in the commands above.

3. In your Internet browser Address field, enter the IP address http://10.10.10.1/admin

(default).

4. Once you are connected, you will be prompted to enter the user name and password.

Enter your user name (default is admin) and password (default is password) and select OK.

5. From the initial menu, select DHCP Server from the System options on the left side of the

menu. The DHCP Server Settings menu will display. Under Modify/Delete a DHCP Server

Pool, select either the LAN_pool or VoIP_pool.

Contact your network administrator if you need assistance changing your computer’s

IP settings.

If you cannot change the PC’s IP address, you must change the NetVanta server’s IP

address.

Select

LAN_pool or

VoIP_pool

from the list of

DHCP server

pools.

6. Select the Numbered Options tab to enter the Option 157 information.

7. Add a new numbered option by entering 157 in the Number field, and the following text string

in the ASCII Text field:

TftpServers=0.0.0.0, FtpServers=10.10.20.1:/ADTRAN, FtpLogin=polycomftp,

FtpPassword=password, Layer2Tagging=True, VlanID=2

Complete this step by selecting Add Numbered Option. The new option and text will appear

in the View/Delete a Numbered Option portion of the menu.

8. Select Apply to complete this task.

9. Repeat Steps 2 through 5 for the remaining DHCP server pool.

10. Select Save at the top right of the current menu. A confirmation message appears if the save

is successful. Select OK to close the window and return to the previous menu.

Create a Session Initiation Protocol (SIP) account for each phone to be installed. SIP accounts

are created using the GUI.

1. Open a GUI session. If you need assistance, follow the steps in Configuring the DHCP

Server Settings on page 1.

2. Select User Accounts from the Voice options on the left side of the menu to display the

Add/Modify/Delete Users menu.

Creating SIP Accounts

1. Select the

Numbered

Options tab.

2. Enter 157 in the

Number field.

3. Enter the ASCII

text string.

4. Select Add

Numbered

Option.

The new numbered

option and its

details appear in

the View/Delete

area.

5. Select Apply.

3. Enter the Extension, First Name, and Last Name. Leave the Phone Type as SIP and the

Phone MAC Address as <Not Set>. This prevents the NetVanta server from attempting to

generate a Polycom configuration file for this account.

4. Select Apply to complete this task.

5. Select Save at the top right of the current menu. A confirmation message appears if the save

is successful. Select OK to close the window and return to the previous menu.

Included in the zipped installation file you received were several configuration files (refer to

Step 5 on page 6 for the list of configuration files). These files must be loaded into the ADTRAN

directory on the NetVanta server. This can be accomplished using any FTP program.

1. If you haven’t already done so, unzip the installation file provided by ADTRAN and save the

files locally.

2. Make a copy of the adtran_000000000000.txt file for each phone you are installing. Replace

the zeros portion of the file name with the MAC address of the phone. The MAC address can

be found on the label on the back of the phone, as well as on the phone’s box.

3. Open the newly created file and edit it by following the instructions provided in the file.

4. If an ADTRAN directory does not already exist on your NetVanta server, create a directory

titled ADTRAN using your FTP program.

Uploading Configuration Files

5. Move the files created for each phone in Step 2 on page 5, as well as the following list to the

ADTRAN directory:

• adtran_000000000000.txt

• iconpixmap.bmp

• language_english.xml

• apadt12r1303.ebin

• btadt12r0204.ebin

• apadt6r1303.ebin

• btadt6r0204.ebin

• adtran_phonebook.csv

The final step in successfully installing an IP 700 Series phone on your network is to load the new

configuration files on the phone. This is accomplished by connecting the phone to the NetVanta

server and setting it to Factory Default. Once the phone reboots, it will load the new configuration

files and be ready to use.

1. Connect the IP phone to one of the NetVanta switch ports. The phone buttons will illuminate,

and after a moment the LCD will display the ADTRAN logo. At this point, the IP phone will

begin running its self-test and the left-most soft key will display Setup.

2. Press the Setup soft key to enter setup mode.

3. At the password prompt, enter the default password 1234.

4. Press 2for Phone Settings.

5. Press 9for Reset.

6. Select the Factory soft key.

7. Select the Ok soft key to reboot the phone.

As the phone reboots, the phone buttons will illuminate, and after a moment the LCD will display

the ADTRAN logo. The IP phone will begin running its self-test. If the phone appears to reboot a

second time, it may be due to an older version of firmware loaded on the phone. If the phone has

an older version of firmware than what is detected on the server, it will download the new version

and reboot.

The file adtran_phonebook.csv is a comma separated file that can be edited to hold

information for up to 300 contacts. You can edit this file (using a spreadsheet

application or text editor) prior to placing it on your NetVanta server. This allows the

phone users to access the phone book via the Directories key on the phone.

Phone Setup

Once the reboot is complete, the phone will register to the NetVanta server and be ready to use.

You can differentiate a registered phone from an unregistered phone by the icon (see below) that

appears on the idle screen.

Registered phone

Unregistered phone

Andere Handbücher für NetVanta 7000 Series

Inhaltsverzeichnis

Andere ADTRAN Netzwerk-Hardware Handbücher

ADTRAN

ADTRAN ACT 1900 Bedienungsanleitung

ADTRAN

ADTRAN Total Access 300 Series Produkthandbuch

ADTRAN

ADTRAN DS3 NIU3 PM Bedienungsanleitung

ADTRAN

ADTRAN ESU LT Bedienungsanleitung

ADTRAN

ADTRAN 1200184L1 Bedienungsanleitung

ADTRAN

ADTRAN Ethernet Over Bonded Copper MX3112 Bedienungsanleitung

ADTRAN

ADTRAN SDX 621i XGS-PON ONT Bedienungsanleitung

ADTRAN

ADTRAN DUAL Nx56/64 1200142L1# Bedienungsanleitung

ADTRAN

ADTRAN Total Access Octal ADSL Bedienungsanleitung

ADTRAN

ADTRAN TOTAL ACCESS 600R Bedienungsanleitung

ADTRAN

ADTRAN ISU 512E Bedienungsanleitung

ADTRAN

ADTRAN NETVANTA OCTAL POE Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 4660 Bedienungsanleitung

ADTRAN

ADTRAN HDSL 3192 HTU-C Bedienungsanleitung

ADTRAN

ADTRAN Total Reach DDS-R Bedienungsanleitung

ADTRAN

ADTRAN NETVANTA 6355 Bedienungsanleitung

ADTRAN

ADTRAN Dial Backup Interface Module 1204006L2 Bedienungsanleitung

ADTRAN

ADTRAN HDSL4 Bedienungsanleitung

ADTRAN

ADTRAN DS3 NIU3 Bedienungsanleitung

ADTRAN

ADTRAN T1 CSU ACE Bedienungsanleitung

ADTRAN

ADTRAN DS3 NIU3 Bedienungsanleitung

ADTRAN

ADTRAN Total Access 832 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 6330 Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 5660 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung