ADTRAN ATLAS 550 Bedienungsanleitung

ATLAS 550 (DC SYSTEM) P/N 1200550L1

For more detailed documentation, visit us online at www.adtran.com

Quick Start Guide

Connecting to the ATLAS 550

Connecting a VT100 terminal (or VT100 terminal emulator) to the CRAFT

interface (on the front panel of the unit) or the CONTROL INinterface (on the rear

panel of the unit) allows access to the terminal menus and management

features of the ATLAS 550.

Perform Steps Below in the Order Listed:

1. Configure a VT100 terminal (or terminal emulation software) with the

following settings:

If the terminal has a parallel setting, disable it and use serial.

2. Connect one end of the 6” data cable (supplied) into the ATLAS 550 CRAFT

or CONTROL INport. (This connection is RJ-45.) Make the connection to the

VT100 terminal as appropriate for your connection. ADTRAN supplies an

RJ-45 to DB-9 adapter for connections to standard DB-9 Communications

(COM) ports.

3. Initiate a terminal session and the LOGIN screen displays. The default

password is password. (Passwords in the ATLAS 550 are case sensitive.)

Data Rate: 9600 baud Stop Bits: 1

Data Bits: 8 Flow Control: None

Parity Bits: None

TEST

ERROR

ALARM

TEST

ERROR

ALARM

STATUS

ONLINE

TEST

12 3 4

NETWORK

MODULES

POWER

ACO

CRAFT

ETHERNET

REMOTE

SYSTEM

ATLAS 550

Network Module LEDs Option Module LEDs

Craft Interface

ACO Switch

Controller LEDs

Craft Pinout

System Status LEDs

The System Status LEDs display the status of the power supply, controller, and

other system parameters for the ATLAS 550. For a more detailed discussion of

the front panel LEDs, refer to Section 2, Engineering Guidelines, of the ATLAS

550 System Manual.

PIN NAME DESCRIPTION

1 GND Ground - connected to unit chassis

2 RTS Request to send - flow control

3 RXDATA Data received by the ATLAS 550

4 DTR Data terminal ready

5 TXDATA Data transmitted by the ATLAS 550

6 CD Carrier detect

7 UNUSED —

8 CTS Clear to send - flow control

LED Description

Power Indicates the status of the power supply

System Indicates the status of the unit controller and other system parameters.

Ethernet Indicates the status of the ethernet port.

Remote Indicates whether a user (Telnet or VT100) is logged in to the unit.

Reviewing the Front Panel

ATLAS 550 (DC SYSTEM) P/N 1200550L1

For more detailed documentation, visit us online at www.adtran.com

Quick Start Guide

ALL EMPTY SLOTS MUST BE

COVERED WITH BLANK PANELS

500 Series

CAUTION: FOR CONTINUED PROTECTION

AGAINST RISK OF FIRE, REPLACE ONLY

WITH SAME TYPE AND RATING OF FUSE.

ETHERNET CONTROL RELAY ALARM

MON

OUTIN

COMNONC GND

500 Series

NETWORK 2

NETWORK 1

500 Series

+Ð

USE COPPER CONDUCTORS ONLY

INPUT:

24Ð48V ,4A FUSE:

5A/48VDC

Network Module Slots Alarm Relay Connection

Control In/Out

10/100BaseT Ethernet

Option Module Slots DC Power Connection

Control In

10/100BaseT Ethernet Pinout

PIN NAME DESCRIPTION

1 GND Ground - connected to unit chassis

2 RTS Request to send - flow control

3 RXDATA Data received by the ATLAS 550

4 DTR Data terminal ready

5 TXDATA Data transmitted by the ATLAS 550

6 CD Carrier detect

7 UNUSED —

8 CTS Clear to send - flow control

PIN NAME DESCRIPTION

1 TX1 Transmit Positive

2 TX2 Transmit Negative

3 RX1 Receive Positive

4,5, 7, 8 — Unused

6 RX2 Receive Negative

Alarm Relay Connection Pinout

PIN NAME DESCRIPTION

1 Normally Closed (NC) Opens when a selected alarm condition is present.

2 Normally Open (NO) Closes when a selected alarm condition is present.

3 Common (COM) Common connection between external circuitry

and NC or NO terminal.

4 Chassis Ground (GND)

Connecting Power to the ATLAS 550

The DC powered ATLAS 550 comes equipped with a DC power supply to furnish

voltages for proper backplane operation. Please refer to Section 3, Network

Turnup Procedures, of the ATLAS 550 System Manual for more detailed

instructions.

• Power to the ATLAS 550 DC System must be from a reliably

grounded +24 or -48 VDC source which is electrically isolated

from the DC source.

• This unit shall be installed in accordance with Article 400 and

364.8 of the NEC NFPA 70.

• The branch circuit overcurrent protection shall be a fuse or

circuit breaker rated minimum 60 VDC, maximum 10A.

• A readily accessible disconnect device, that is suitably

approved and rated, shall be incorporated in the field wiring.

• Maximum recommended ambient operating temperature is

45°C

Reviewing the Rear Panel Design

DC Power Supply Connection

PIN NAME +24 VDC Source -48 VDC Source

1 + +24 VDC Ground (GND)

2 - Ground (GND) -48VDC

Andere Handbücher für ATLAS 550

Dieses Handbuch passt für folgende Modelle

Andere ADTRAN Netzwerk-Router Handbücher

ADTRAN

ADTRAN Total Access 904 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3448 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3100 Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3000 Series Handbuch

ADTRAN

ADTRAN Express L768 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3100 Series Bedienungsanleitung

ADTRAN

ADTRAN Total Access 5000 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 5305 Handbuch

ADTRAN

ADTRAN 1200422L1 Handbuch

ADTRAN

ADTRAN Total Access 1248 Bedienungsanleitung

ADTRAN

ADTRAN 1203870G1 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1355 PWR Bedienungsanleitung

ADTRAN

ADTRAN 1200350L1 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3430 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3200 series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 4305 Handbuch

ADTRAN

ADTRAN NetVanta 3448 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3148 Series Handbuch

ADTRAN

ADTRAN NetVanta 3305 Bedienungsanleitung

ADTRAN

ADTRAN SR700ac Bedienungsanleitung

ADTRAN

ADTRAN 424RG Bedienungsanleitung

ADTRAN

ADTRAN TOTAL ACCESS 600R Benutzerhandbuch

ADTRAN

ADTRAN Total Access 544R Benutzerhandbuch

ADTRAN

ADTRAN Express XL 1200070L1 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise