Advanced Instruments OsmoTECH Einrichtungshandbuch

Installation & Training Guide

OsmoTECH Osmometer

MP00039 Rev 1

PCN00517

•For full installation and

setup instructions as well

as detailed instrument

operation please refer to

the OsmoTECH User

Manual.

Disclaimer

Note: Not for patient diagnostic use

Installation and Setup

Instrument Operation

Standards and Controls

Calibration

Maintenance

Topics

•Step 1 –Find a location for the instrument

oEnsure adequate space

oUse a properly grounded, three-prong electrical outlet capable of supplying 0.5 amperes at 100-

240 VAC (50-60 Hz) within 5 feet of instrument placement

•Step 2 –Unpack the instrument

oUse enclosed packing list to verify all accessories

and supplies were received

oIf any items are damaged or missing, notify the carrier,

dealer, and Advanced Instruments within 24 hours

oComplete the online warranty card to register your

product at www.aicompanies.com/warranty

•Step 3 –Connecting to the printer (optional)

oYou can connect an Epson dot matrix printer to the OsmoTECH.

oPurchase the printer through Advanced Instruments.

Installation and Setup

•Step 4 –Place the Micro-Sample Test Kit on the

instrument (reorder part number: TECH500)

•A Micro-Sample Test Kit must be in place on the top

left of the instrument before testing can begin. The

box must be oriented so that the chamber cleaners

are in front and the box opens away from you.

•An error message appears if the test kit is not in

place when you attempt to run a test.

•Once you’ve run 250 tests, you must replace the test

kit; otherwise, you won’t be able to run a new test.

Installation and Setup

•Step 5 –Connecting to a network (optional)

•To connect the OsmoTECH to a laboratory information system (LIS), to a local area network

(LAN), and/or to enable the webserver, plug an Ethernet cable that connects to your network

into the Ethernet port on the back of the OsmoTECH unit.

•Refer to the User Guide to configure the communication settings in the OsmoTECH software.

Installation and Setup

•Step 6 –Powering up the instrument

•Connect the power cord to the back of the instrument and insert the plug into the power outlet.

•Turn on the power to the instrument using the rocker switch on the back. Depress the side

marked with the Isymbol. When the unit powers up, the Welcome screen displays.

•After a few moments, the OsmoTECH Home screen displays. From the Home Screen, you can

initiate sample testing and view the results, Initially, the instrument status shown in the green

status banner is Osmometer Ready.

Installation and Setup

•Step 7 –Configuring the OsmoTECH settings

•Review and/or configure the following instrument settings before using the OsmoTECH. Refer

to the User Guide for instructions.

•If the date or time displayed on the unit is incorrect, set the current date and time.

•If synchronizing the clock, configure the OsmoTECH to connect to your local area network (LAN).

−To use DHCP (dynamically assigned IP):

−Connect the OsmoTECH to the network

−Enable the “Time Server” in the Date & Time screen

−Select the time zone location

−Enter a server name of choice

−To use Static IP:

−Connect the OsmoTECH to the network

−Enable the “Time Server” in the Date & Time screen

−Select the time zone location

−Enter a server name of choice as a numerical value

−Set the Subnet Mask in the LIS/LAN screen to match the local network value

−Set the Default Gateway in the LIS/LAN screen to match the local network value

Installation and Setup

•Step 7 –Configuring the OsmoTECH settings (cont.)

•If the unit’s language is not set appropriately for your site, change the language settings.

•If desired, set up user accounts.

•If desired, assign restrictions for operator-level accounts, set the password expiration period and

configure the system to require a User ID and/or Sample ID before beginning a test.

•If desired, configure the OsmoTECH to communicate with your laboratory information system (LIS).

•If desired, set up control limits.

•If desired, enable webserver:

−Enable the webserver from SETTINGS > LIS/LAN > LAN screen.

−Go to the information screen and copy the assigned IP address

into any internet browser.

−The embedded webserver looks similar to a website.

Installation and Setup

Instrument Operation

Standards and Controls

Calibration

Maintenance

Topics

Andere Handbücher für OsmoTECH

Inhaltsverzeichnis

Andere Advanced Instruments Messgerät Handbücher

Advanced Instruments

Advanced Instruments OsmoPRO Bedienungsanleitung

Advanced Instruments

Advanced Instruments GPR-1800 AIS LD Bedienungsanleitung

Advanced Instruments

Advanced Instruments AE Series Bedienungsanleitung

Advanced Instruments

Advanced Instruments 3250 Bedienungsanleitung

Advanced Instruments

Advanced Instruments OsmoTECH PRO Einrichtungshandbuch

Advanced Instruments

Advanced Instruments GPR-IN190 Bedienungsanleitung

Advanced Instruments

Advanced Instruments 3300 Bedienungsanleitung

Advanced Instruments

Advanced Instruments 3300 Bedienungsanleitung

Advanced Instruments

Advanced Instruments OsmoPRO Bedienungsanleitung

Advanced Instruments

Advanced Instruments GPR-1200 Bedienungsanleitung

Advanced Instruments

Advanced Instruments A2O Bedienungsanleitung

Advanced Instruments

Advanced Instruments GPR-2500 Bedienungsanleitung

Advanced Instruments

Advanced Instruments 3320 Bedienungsanleitung

Advanced Instruments

Advanced Instruments 4C3 Bedienungsanleitung

Advanced Instruments

Advanced Instruments OsmoTECH PRO Bedienungsanleitung

Advanced Instruments

Advanced Instruments 3250 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung