Advantech POS-761F Bedienungsanleitung

POS-761F

Socket 370 SBC for POS, Kiosks

and Gaming applications

User’s Manual

POS-761F User’s Manual ii

nal manufacturer reserves the right to make improvements to the products

described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmit-

ted in any form or by any means without the prior written permission of

the original manufacturer. Information provided in this manual is

intended to be accurate and reliable. However, the original manufacturer

assumes no responsibility for its use, nor for any infringements upon the

rights of third parties that may result from such use.

Acknowledgements

Award is a trademark of Award Software International, Inc.

VIA is a trademark of VIA Technologies, Inc.

IBM, PC/AT, PS/2 and VGA are trademarks of International Business

Machines Corporation.

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows® is a registered trademark of Microsoft Corp.

RTL is a trademark of Realtek Semi-Conductor Co., Ltd.

ESS is a trademark of ESS Technology, Inc.

UMC is a trademark of United Microelectronics Corporation.

SMI is a trademark of Silicon Motion, Inc.

Creative is a trademark of Creative Technology LTD.

All other product names or trademarks are properties of their respective

owners.

For more information on this and other Advantech products, please visit

our websites at: http://www.advantech.com

http://www.advantech.com/ppc

For technical support and service, please visit our support website at:

http://support.advantech.com

This manual is for the PPC-123.

Part No. 2007076110

1st Edition, Feb. 2003

iii

FCC Class B

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a residential environment. This

equipment generates, uses and can radiate radio frequency energy. If not

installed and used in accordance with this user's manual, it may cause

harmful interference to radio communications. Note that even when this

equipment is installed and used in accordance with this user's manual,

there is still no guarantee that interference will not occur. If this equip-

ment is believed to be causing harmful interference to radio or television

reception, this can be determined by turning the equipment on and off. If

interference is occurring, the user is encouraged to try to correct the inter-

ference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment to a power outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Warning! Any changes or modifications made to the

equipment which are not expressly approved by

the relevant standards authority could void your

authority to operate the equipment.

POS-761F User’s Manual iv

Packing List

Before you begin installing your card, please make sure that the following

materials have been shipped:

• 1 POS-761F all-in one single board computer

• 1 CD-ROM or disks for utility, drivers, and manual (in PDF format)

• 1 warranty certificate

• 1 UDMA 66 40-pin flat cable

• 1 startup manual

• 2 serial port cables

• 1 audio cable (optional)

If any of these items are missing or damaged, contact your distributor or

sales representative immediately.

Additional Information and Assistance

Step 1. Visit the Advantech web site at www.advantech.com where you

can find the latest information about the product.

Step 2. Contact your distributor, sales representative, or Advantech's

customer service center for technical support if you need addi-

tional assistance. Please have the following information ready

before you call:

• Product name and serial number

• Description of your peripheral attachments

• Description of your software (operating system, version, application

software, etc.)

• A complete description of the problem

• The exact wording of any error messages

POS-761F User’s Manual vi

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User's Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp

cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or let-

ting it fall may cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment

from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power

source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service

personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according

to the user's manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE

THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR

ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE

EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY

REPLACED.REPLACE ONLY WITH THE SAME OR EQUIVALENT

TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED

BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUC-

TIONS.

The sound pressure level at the operator's position according to IEC 704-1:1982 is

no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan-

tech disclaims all responsibility for the accuracy of any statements contained

herein.

vii

W i c h t i g e S i c h e r h e i s h i n w e i s e

1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie

Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch

zur Reinigung.

4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht

zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen

oder Fallen könnte Verletzungen hervorrufen.

7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor über-

hitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt wer-

den.

8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.

9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann.

Es sollte auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu

beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom

Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädi-

gung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten

in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus-

lösen.

13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen

Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen

und von einer qualifizierten Servicestelle zu überprüfen:

a - Netzkabel oder Netzstecker sind beschädigt.

b - Flüssigkeit ist in das Gerät eingedrungen.

c - Das Gerät war Feuchtigkeit ausgesetzt.

d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert

oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.

e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batte-

rie.Ersatz nur durch densellben order einem vom Hersteller empfohlene-

mahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des

Herstellers.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000

beträgt 70dB(A) oder weiger.

DISCLAIMER: This set of instructions is given according to IEC704-1.

Advantech disclaims all responsibility for the accuracy of any statements

contained herein.

POS-761F User’s Manual viii

Caution! Danger of explosion if battery is incorrectly

replaced. Replace only with the same or equiv-

alent type recommended by the manufacturer.

Dispose of used batteries according to the man-

ufacturer’s instructions.

Contents

Chapter 1 General Information ........................................2

1.1 Introduction ....................................................................... 2

1.2 Features ............................................................................. 3

1.3 Specifications .................................................................... 4

1.4 Board Dimensions............................................................. 6

Figure 1.1:Board Dimensions (Component Side)........... 6

Figure 1.2:Board Dimensions (Solder Side)................... 7

Chapter 2 Installation ......................................................10

2.1 Jumpers............................................................................ 10

Table 2.1:Jumpers......................................................... 10

2.2 Connectors....................................................................... 10

2.3 Locating jumpers and connectors.................................... 13

Figure 2.1:Locating Jumpers ........................................ 13

2.4 Setting Jumpers ............................................................... 14

Figure 2.2:Locating Connectors (Component Side)..... 14

2.5 CPU installation and upgrading ...................................... 15

2.5.1 Installing a CPU in the ZIF socket................................ 16

2.5.2 CMOS clear (J4) ........................................................... 17

Table 2.3:CMOS clear (J4)........................................... 17

2.6 DRAM installation .......................................................... 17

2.6.1 DIMM DRAM (DIMM 1 and DIMM 2)...................... 17

2.7 Primary (3.5") IDE connector (CN12)............................ 17

2.7.1 Connecting the hard drive............................................. 18

2.8 Secondary (2.5") IDE connector (CN10) ........................ 18

2.9 FDD connector (CN13)................................................... 18

2.9.1 Connecting the floppy drive ......................................... 19

2.10 LPT1 (primary parallel port) connectors . (CN28/CN29)19

2.11 LPT2 (secondary parallel port) connector (CN30) ......... 19

2.12 Keyboard/mouse connectors (CN4, CN6) ...................... 20

Table 2.4:Keyboard/mouse select (J1).......................... 20

2.13 Power connectors (CN5, CN7, CN1,CN19) ................... 20

2.13.1 Main power connector (CN5)....................................... 20

2.13.2 ATX power input connector (CN7).............................. 20

2.13.3 Fan power supply connector (CN1,CN19) ................... 20

2.14 Audio interfaces (CN2, CN3).......................................... 20

2.14.1 Audio connector (CN3) ................................................ 21

2.14.2 CD audio-in connector (CN2)....................................... 21

2.15 Serial (COM1- 4)(CN20/21,CN14/16,CN25,CN22) ...... 21

2.15.1 Primary(COM1:CN20/CN21,COM2:CN14/CN16)..... 21

2.15.2 Secondary(COM3: CN25, COM4: CN22) ................... 21

POS-761F User’s Manual x

2.16 COM2 RS-232/422/485 (J10, J11 and J12) .................... 22

Table 2.5:COM2 RS-232/422/485 (J10, J11 & J12) .... 22

2.17 COM1- 4 RI pin +5/+12V (J15,J16,J14,J17).................. 22

Table 2.6:COM1, COM2 RI/power select (J15)........... 22

Table 2.7:COM1, COM2 RI/power select (J16)........... 22

Table 2.8:COM3, COM4 R1/power select (J17).......... 22

2.18 VGA interface connections ............................................. 23

2.18.1 CRT display connector (CN36 and CN37)................... 23

2.18.2 Flat panel display connector (CN31)............................ 23

Table 2.9:COM3, COM4 R1/power select (J14).......... 23

2.18.3 LCD power setting (J20)............................................... 24

Table 2.10:LCD power (J20)........................................ 24

2.19 Ethernet configuration..................................................... 24

2.19.1 RJ-45 connector (CN11)............................................... 24

2.19.2 Network boot ................................................................ 24

2.20 Watchdog timer configuration ........................................ 25

2.20.1 Watchdog timer action (J13)......................................... 25

Table 2.11:Watchdog Function J13.............................. 25

2.21 USB connector (CN26,CN27)......................................... 25

2.22 DOC® 2000 address select (J44).................................... 26

Table 2.12:DOC® 2000 address select (J44) ............... 26

2.23 Mouse and IRQ12 function select (J1)............................ 27

2.24 Digital I/O (J7: 4 Outputs, 4 Inputs) ............................... 27

2.24.1 Digital output programming ......................................... 28

Table 2.14:Digital output programming ....................... 28

2.24.2 Digital output solenoid wiring examples ...................... 28

Figure 2.3:POS-761F digital output solenoid wiring.... 29

Chapter 3 Software Configuration .................................32

3.1 Introduction ..................................................................... 32

3.2 VGA display firmware configuration ............................. 32

Figure 3.1:VGA setup screen........................................ 33

3.3 Connections for four standard LCDs .............................. 34

Table 3.1:Sharp LM64183P LCD (CN35) ................... 34

3.4 Ethernet software configuration...................................... 38

Chapter 4 Award BIOS Setup.........................................40

4.1 System test and initialization........................................... 40

4.1.1 System configuration verification................................. 40

4.2 Award BIOS setup .......................................................... 41

4.2.1 Entering setup ............................................................... 41

Figure 4.1:Setup Program Initial Screen....................... 41

4.2.2 Standard CMOS setup .................................................. 41

Figure 4.2:CMOS Setup Screen.................................... 42

4.2.3 BIOS features setup ...................................................... 43

Inhaltsverzeichnis

Andere Advantech Computerhardware Handbücher

Advantech

Advantech POC-615 Series Bedienungsanleitung

Advantech

Advantech MIC-300 Installations- und Betriebshandbuch

Advantech

Advantech AIMB-788 Bedienungsanleitung

Advantech

Advantech PCM-3362 Bedienungsanleitung

Advantech

Advantech IPC-610B Bedienungsanleitung

Advantech

Advantech PCE-GIGE2 Installations- und Betriebshandbuch

Advantech

Advantech MIO-2361 Series Installations- und Betriebshandbuch

Advantech

Advantech PCE-5B05V-30B1E Installations- und Betriebshandbuch

Advantech

Advantech MIO-5376 Installations- und Betriebshandbuch

Advantech

Advantech PPC-IPS Bedienungsanleitung

Advantech

Advantech PCM-3643 Bedienungsanleitung

Advantech

Advantech PPC-6150A Bedienungsanleitung

Advantech

Advantech ECU-479 Series Bedienungsanleitung

Advantech

Advantech AIMC-3421 Installations- und Betriebshandbuch

Advantech

Advantech AIMC-3202 Installations- und Betriebshandbuch

Advantech

Advantech MIO-2375 Installations- und Betriebshandbuch

Advantech

Advantech PCL-818L Bedienungsanleitung

Advantech

Advantech SOM-5786 Bedienungsanleitung

Advantech

Advantech PPC-3151 Bedienungsanleitung

Advantech

Advantech IPC-619 Bedienungsanleitung

Advantech

Advantech SOM-7583 Bedienungsanleitung

Advantech

Advantech MIC-75G20-10A2 Installations- und Betriebshandbuch

Advantech

Advantech PCIe-1674 Bedienungsanleitung

Advantech

Advantech UNO-238 V2 Installations- und Betriebshandbuch

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung