Advantech AIM 10W Bedienungsanleitung

1



AIM 10W Computer

User Manual

2



V1.0

The documentation and the software included with this product are copyrighted

2017 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves

the right to make improvements in the products described in this manual at any time

without notice. No part of this manual may be reproduced, copied, translated or

transmitted in any form or by any means without the prior written permission of

Advantech Co., Ltd. Information provided in this manual is intended to be accurate

and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor

for any infringements of the rights of third parties, which may result from its use.

Acknowledgements

All other product names or trademarks are properties of their respective owners.

3



Declaration of Conformity

CE Conformity Statement

Radio products with the CE alert marking comply with the R&TTE Directive

(1999/5/EC) issued by the Commission of the European Community. Compliance

with this directive implies conformity to the following European Norms (in brackets

are the equivalent international standards).

• EN 60950-1 (IEC60950-1) - Product Safety

• EN 300 328 Technical requirement for radio equipment

• ET S301 489 General EMC requirements for radio equipment

Products that contain the radio transmitter are labeled with CE alert marking and

may also carry the CE logo.

FCC Compliance Statement

15.105 Class B digital device or

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly

approved by the party responsible for compliance could void the user's authority to

operate this equipment. (Example: use only shielded interface cables when

connecting to computer or peripheral devices).

4



This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that

may cause undesired operation.

15.21

Any changes or modifications not expressly approved by the party responsible for

compliance could void the authority to operate equipment.

This device and its antenna must not be co-located or operating in conjunction with

any other antenna or transmitter.

End-users and installers must be provided with antenna installation instructions and

transmitter operating conditions for satisfying RF exposure compliance.

For product available in the USA/Canada market, only channel 1~11 can be operated.

Selection of other channels is not possible.

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment for body-worn configuration in direct contact to the

phantom.

This device complies with FCC radiation exposure limits set forth for an uncontrolled

environment.

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. End user must follow the specific operating instructions

for satisfying RF exposure compliance. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for

exposure to radio waves established by the Federal Communications

Commission (USA). These requirements set a SAR limit of 1.6 W/kg

averaged over one gram of tissue. The highest SAR value reported under

this standard during product certification for use when properly worn on the body is

1.0W/kg

5



IC warning statement

ThisdevicecomplieswithIndustryCanada’slicence‐exemptRSSs.Operationis

subjecttothefollowingtwoconditions:  (1)Thisdevicemaynotcauseinterference;

and  (2)Thisdevicemustacceptanyinterference,includinginterferencethatmay

causeundesiredoperationofthedevice.



LeprésentappareilestconformeauxCNRd'IndustrieCanadaapplicablesaux

appareilsradioexemptsdelicence.L'exploitationestautoriséeauxdeuxconditions

suivantes:(1)l'appareilnedoitpasproduiredebrouillage,et(2)l'utilisateurde

l'appareildoitacceptertoutbrouillageradioélectriquesubi,mêmesilebrouillageest

susceptibled'encompromettrelefonctionnement.



ThisradiotransmitterhasbeenapprovedbyIndustryCanadatooperatewiththe

antennatypeslistedbelowwiththemaximumpermissiblegainandrequired

antennaimpedancearestrictlyprohibitedforusewiththisdevice.



LepresentemetteurradioaeteapprouveparIndustrieCanadapourfonctionner

aveclestypesd'antenneenumeresci‐dessousetayantungainadmissiblemaximal

etl'impedancerequisepourchaquetyped'antenne.Lestypesd'antennenoninclus

danscetteliste,oudontlegainestsuperieuraugainmaximalindique,sont

strictementinterditspourl'exploitationdel'emetteur.

(i)the device for operation in the band 5150–5250 MHz is only for indoor use to

reduce the potential for harmful interference to co-channel mobile satellite systems;

(For devices installed in vehicles point i. is not required.)

Users should also be advised that high-power radars are allocated as primary users

(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these

radars could cause interference and/or damage to LE-LAN devices.

(i) l'appareil pour fonctionner dans la bande 5150-5250 MHz est réservé à une

utilisation en intérieur afin de réduire les risques d'interférences nuisibles à la

co-canal systèmes mobiles par satellite;

Devraient également être informés les utilisateurs que les radars à haute puissance

sont désignés comme utilisateurs principaux (c.-à-utilisateurs prioritaires) des

bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient provoquer des

interférences et / ou endommager les appareils LE-LAN.

6



IC Radiation Exposure Statement

This EUT is compliance with SAR for general population/uncontrolled exposure limits

in IC RSS-102. This equipment should be installed and operated with minimum

distance 0 cm between the radiator & your body.

Cet EUT est la conformite avec SAR pour la population generale / les limites

d'exposition incontrolees dans IC RSS-102. Cet equipement doit etre installe et

utilise a une distance minimale de 0 cm entre le radiateur et votre corps.

This equipment complies with ISED radiation exposure limits set forth for an

uncontrolled environment. End user must follow the specific operating instructions

for satisfying RF exposure compliance. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio

waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg

averaged over one gram of tissue. The highest SAR value reported under this

standard during product certification for use when properly worn on the body.

Cet équipement est conforme aux limites d’exposition aux rayonnements ISED

établies pour un environnement non contrôlé. L’utilisateur final doit suivre les

instructions spécifiques pour satisfaire les normes. Cet émetteur ne doit pas être

co-implanté ou fonctionner en conjonction avec toute autre antenne ou

transmetteur.



NCC Warning Statement

Article 12

Without permission, any company, firm or user shall not alter the frequency,

increase the power, or change the characteristics and functions of the original design

of the certified lower power frequency electric machinery.

Article 14

The application of low power frequency electric machineries shall not affect the

navigation safety nor interfere a legal communication, if an interference is found,

the service will be suspended until improvement is made and the interference no

longer exists.

7



Safety Instructions

1. Read these safety instructions carefully.

2. Keep this user manual for later reference.

3. Disconnect this equipment from AC outlet before cleaning. Do not use liquid or

spray detergents for cleaning.

4. Keep this equipment away from hazard locations.

5. Put this equipment on a reliable surface during installation. Dropping it or

letting it fall could cause damage.

6. Do not leave this equipment in an environment unconditioned where the

storage temperature under -20C or above 60C, it may damage the

equipment.

7. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

8. Place the AC power adapter such a way that people cannot step on it. Do not

place anything over the power adapter.

9. All cautions and warnings on the equipment should be noted.

10. If the equipment is not used for long time, disconnect it from the power

source to avoid being damaged by transient over-voltage.

11. Never pour any liquid into slots of the AIM 10W Series. This could cause fire or

electrical shock.

12. Never open or disassemble the equipment. For safety reasons, the equipment

should be opened only by qualified service personnel.

13. If any of the following situations arises, get the equipment checked by service

personnel:

a. The power adapter plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well or you cannot get it to work according to

user manual.

e. The equipment has obvious signs of breakage.

14. This product is intended to be supplied by a UL Listed Power Adapter or DC

power source, rated 19 Vdc, 3.42A min. for model AIM 10W and Tma 50 degree

C, if need further assistance, please contact Advantech for further

information.

8



Battery Safety

Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the

same type recommended by the manufacturer, discard used batteries according to

the manufacturer's instructions.

Attention : Danger d'explosion si la batterie est inexactement remplacée. Remplacez

seulement avec la même chose ou le type recommandé par le fabricant, jettent les

batteries utilisées instructions de s selon fabricant des'.

Mistreat the battery used in this device may present a risk of fire or chemical burn.

Do not attempt to disassemble the computer or its accessories.

Only qualified personal is allowed to replace the battery.

Do not dispose batteries in a fire and check with local authorities for disposal

instructions.

AIM 10W can only be equipped with standard battery pack with Getac AIM-BAT-10

2300mAH Polymer Lithium Ion Battery. Use of another battery may present a risk of

fire or explosion.

Battery Charge Notice

It is important to consider the environment temperature whenever you are charging

the Lithium-Ion battery pack. The process is more efficient at normal room

temperature or slightly cooler. It is essential that you charge batteries within the

stated range of 0°C to 40°C. Charging batteries outside of the specified range could

damage the batteries and shorten their charging life cycle.

Storage and Safety Notice

Although charge Lithium-Ion batteries may be left unused for several months, their

capacity may be depleted due to the buildup of internal resistance. If this happens

they will require recharging prior to use. Lithium Ion batteries may be stored at

temperatures between -10°C to 60°C, however they may be depleted more rapidly

at the high end of this range. It is recommended to store AIM 10W within normal

room temperature ranges.T-W101 User Manual

9



WEEE

FollowinginformationisonlyforEU-memberstates:

The use of the symbol indicates that this product may not be treated as household

waste. By ensuring this product is disposed of correctly, you will help prevent

potential negative consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of this product. For more

information about recycling of this product, please contact your local city office,

your household waste disposal service or the shop where you purchased the product.

Technical Support and Assistance

1. Visit the Advantech website at http://support.advantech.com where you can find

the latest information about the product.

2. Contact your distributor, sales representative, or Advantech's customer service

center for technical support if you need additional assistance. Please have the

following information ready before you call:

– Product name and serial number

– Description of your peripheral attachments

– Description of your software (operating system, version, application software,

etc.)

– A complete description of the problem

– The exact wording of any error messages

10



TABLE OF CONTENT

Chapter 1 Introduction.............................................................................................12

1.1SymbolsUsedinthisManual.........................................................................................13

1.2ProductFeatures...........................................................................................................13

1.3PackageContents..........................................................................................................13

1.4ProductSpecifications...................................................................................................14

1.4.1 Technical Specifications ........................................................... 14

1.4.2 Product Outlook and Dimensions ................................................. 16

1.5ExploringtheAIM10W.................................................................................................17

1.5.1 Front View..............................................................................1

1.5.2 Rear View............................................................................. 18

1.5.3 Right View............................................................................ 19

1.5.4 Left View ............................................................................. 20

1.5.5 Bottom View ......................................................................... 21

Chapter 2 Getting Started.......................................................................................22

2.1ChargetheComputer....................................................................................................22

2.2TurnontheComputer...................................................................................................23

2.3SleepMode....................................................................................................................23

2.4Operatethecomputer...................................................................................................24

2.5LEDindicatorstatus.......................................................................................................24

Chapter 3 Basic Setups.............................................................................................25

3.1Windows10IoTEnterpriseBasicSetups......................................................................26

Chapter 4 Running applications..............................................................................27

4.1Installingapplications....................................................................................................27

4.1.1 Install applications with Windows 10 IoT Enterprise .......................... 28

Chapter 5 Maintenance............................................................................................29

5.1MaintainingtheLCDDisplay..........................................................................................29

5.2CleaningtheAIM10W...................................................................................................29

Inhaltsverzeichnis

Andere Advantech Desktop Handbücher

Advantech

Advantech TREK-688 Bedienungsanleitung

Advantech

Advantech ARK-3380 Bedienungsanleitung

Advantech

Advantech USM-260 Bedienungsanleitung

Advantech

Advantech TPC-5212W Series Bedienungsanleitung

Advantech

Advantech ARK-5280 Series Bedienungsanleitung

Advantech

Advantech EPC-T2286 Series Bedienungsanleitung

Advantech

Advantech PCA-6013 Installations- und Betriebshandbuch

Advantech

Advantech UNO-2372G-J1 Series Bedienungsanleitung

Advantech

Advantech DS-085 Series Bedienungsanleitung

Advantech

Advantech PPC-3100 Bedienungsanleitung

Advantech

Advantech PPC-102 Bedienungsanleitung

Advantech

Advantech UNO247J1N12502-T Bedienungsanleitung

Advantech

Advantech ARK-1388V Bedienungsanleitung

Advantech

Advantech ARK-3381 Series Bedienungsanleitung

Advantech

Advantech PCA-6773 Installations- und Betriebshandbuch

Advantech

Advantech TREK-743 Bedienungsanleitung

Advantech

Advantech ITA-5231 Series Installations- und Betriebshandbuch

Advantech

Advantech ARK-3360 Bedienungsanleitung

Advantech

Advantech EPC-U3233 Bedienungsanleitung

Advantech

Advantech AIR-300 Bedienungsanleitung

Advantech

Advantech ITA-2231 Series Bedienungsanleitung

Advantech

Advantech ITA-1611 Series Bedienungsanleitung

Advantech

Advantech EPC-R7200 Bedienungsanleitung

Advantech

Advantech TPC-1570H Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung