AEG Protect C.1000 Bedienungsanleitung

OPERATING INSTRUCTIONS

Protect C.1000

Protect C.2000

Protect C.3000

Protect C

Thank you for purchasing the AEG UPS PROTECT C

from AEG Power Solutions.

Safety information and operating instructions are included in

this manual. To ensure correct use of the UPS, please read this

manual thoroughly before operating it. Use this manual properly.

1.Notes on these Operating Instructions .................. 6

2.General Information................................................... 8

2.1Technology ................................................................... 8

2.2System Description ....................................................... 9

2.3Technical information.................................................. 11

3.Safety ........................................................................ 16

3.1General Safety Instructions......................................... 16

3.2Safety Instructions for Protect C ................................. 17

3.3CE-Certificate.............................................................. 20

4.Set-Up and Operation .............................................. 21

4.1Unpacking and Inspection........................................... 21

4.2Point of Installation...................................................... 22

5.Overview Connections, Operating / Display

Elements ................................................................... 23

5.1Front View................................................................... 23

5.2Rear View (Connections) ............................................ 24

6.Commissioning ........................................................ 26

6.1Mechanical Set-Up...................................................... 26

6.2External Battery Extension.......................................... 27

6.3Power Supply.............................................................. 28

6.4Consumer Connection ................................................ 29

7.Operation and usage ............................................... 31

7.1Initial Installation ......................................................... 31

7.1.1Switching on UPS ............................................... 31

7.1.2Switching off UPS ............................................... 31

7.2Control Panel .............................................................. 32

7.2.1Overview ............................................................. 32

7.2.2Indicators (LEDs) ................................................ 32

7.2.3Operating (Navigation) ........................................ 33

7.3Display (Main Menu) ................................................... 34

7.3.1UPS Status Display............................................. 34

7.3.2Event Log............................................................ 38

7.3.3Measurements .................................................... 39

CONTENT

7.3.4Control ................................................................ 39

7.3.5Identification........................................................ 40

7.3.6Settings ............................................................... 41

8.Interfaces and communication............................... 46

8.1RS232 and USB Computer Interfaces ........................ 46

8.2Communication slot .................................................... 46

8.3Shutdown- und UPS Management Software ............. 47

8.4EPO (Emergency Power Off)...................................... 48

9.Trouble Shooting ..................................................... 49

9.1Malfunctions................................................................ 49

9.1.1Alarm- / Error messages ..................................... 49

10.Maintenance ............................................................. 54

10.1Battery Charging ......................................................... 54

10.2Maintenance ............................................................... 54

10.2.1Visual Check ....................................................... 54

10.2.2Checking the Battery........................................... 55

10.2.3Fan Checking...................................................... 55

10.3Battery replacement.................................................... 55

11.Storage, Dismantling and Disposal ....................... 57

11.1Storage ....................................................................... 57

11.2Dismantling ................................................................. 57

11.3Disposal ...................................................................... 57

12.Glossary.................................................................... 59

12.1Technical Terms ......................................................... 59

12.2Key Word Register...................................................... 61

DUTY TO PROVIDE INFORMATION

These operating instructions will help you to install and operate the

Uninterruptible Power Supply (UPS) PROTECT C.1000, PROTECT C.2000

or PROTECT C.3000 as well as the associated external battery units

PROTECT C.1000 BP or PROTECT C.2030 BP – all referred to as

PROTECT C in this document – safely and properly, and for its intended

purpose. These operating instructions contain important information

necessary to avoid dangers during operation. Please read these

instructions carefully prior to commissioning!

THESE OPERATING INSTRUCTIONS ARE A COMPLETE

PART OF THE PROTECT C

The owner of this unit is obliged to communicate the full content of these

operating instructions to all personnel transporting or starting the

PROTECT C or performing maintenance or any other work on the unit.

VALIDITY

These operating instructions comply with the current technical

specifications of the PROTECT C at the time of delivery. The contents

do not constitute a subject matter of the contract, but serve for

information purposes only.

WARRANTY AND LIABILITY

We reserve the right to alter any specifications given in these operating

instructions, especially with regard to technical data and operation, prior

to start-up or as a result of service work. Claims in connection with

supplied goods must be submitted within one week of receipt, along with

the packing slip. Subsequent claims cannot be considered.

The warranty does not apply to damage caused by non-compliance with

these instructions (such damage also includes damaging the warranty

seal). AEG will accept no liability for consequential damage. AEG

reserves the right to rescind all obligations such as warranty

agreements, service contracts, etc. entered into by AEG and its

representatives without prior notification in the event of maintenance and

repair work being carried out with anything other than original AEG spare

parts or spare parts purchased by AEG.

1. NOTES ON THESE OPERATING

INSTRUCTIONS

HANDLING

PROTECT C is designed and constructed so that all necessary steps for

start-up and operation can be performed without any internal

manipulation of the unit. Maintenance and repair work may only be

performed by trained and qualified personnel.

Illustrations are provided to clarify and facilitate certain steps.

If danger to personnel and the unit cannot be ruled out in the case of

certain work, it is highlighted accordingly by pictograms explained in

chapter 3.

HOTLINE

If you still have questions after having read these operating instructions,

please contact your dealer or our “Hotline”:

Tel: +49 2902 763100

Internet: www.aegps.com

No part of these operating instructions may be transmitted, reproduced

and/or copied by any electronic or mechanical means without the

express prior written permission of AEG.

2.1 TECHNOLOGY

PROTECT C is an Uninterruptible Power Supply (UPS) for essential

loads such as PCs, workstations, servers, network components,

telecommunication equipment and similar devices. It consists of:

Mains filter with surge voltage protection (device protection/

class D) and mains energy backfeed protection

Rectifier section with PFC logic (power factor correction unit)

Separate battery charger with switch mode power supply technology

Sealed, maintenance-free battery system as energy storage medium

with downstream DC/DC converter unit

IGBT inverter for continuous supply of connected loads with

sinusoidal AC voltage

Automatic bypass as additional passive redundancy

Control unit based on digital signal processor technology

2. GENERAL INFORMATION

2.2 SYSTEM DESCRIPTION

The UPS is connected to a shockproof socket between the public utility’s

mains and the loads to be protected.

The power section of the rectifier converts the mains voltage to DC

voltage for supplying the inverter. The circuit technology used (PFC)

enables sinusoidal current consumption and therefore operation with

little system disturbance. A separate, second rectifier (charging REC set

up using switch mode power supply technology) is responsible for

charging or trickle-charging the battery connected in the intermediate

circuit. The configuration of this charging REC means the harmonic

content of the charging current for the battery is almost zero, so the

service life of the battery is increased even more. The inverter is

responsible for converting the DC voltage into a sinusoidal output

voltage. A microprocessor-controlled control system based on pulse-

width modulation (PWM) in conjunction with an extremely quickly

pulsating IGBT power semiconductors of the inverter guarantee that the

voltage system on the protected busbar is of the highest quality and

availability.

In the event of mains faults (e.g. power outage), the voltage continues to

be supplied from the inverter to the load without any interruption. From

this point onwards, the inverter draws its power from the battery instead

of the rectifier. No switching operations are necessary; this means there

is no interruption in the supply to the load.

The automatic bypass serves to increase the reliability of the supply

further. It switches the public mains directly through to the load if there

is an inverter malfunction. As a result, the automatic bypass represents

an extra passive redundancy for the load.

The graphical LC display used provides for versatile use and easy

operation. Such a convenient feature as an emergency power off contact

round out the standard interface selection (USB, RS232, communication

slot).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AEG UPS Handbücher

AEG

AEG Protect D. 6000 (BP) Bedienungsanleitung

AEG

AEG PDU 10-1 Bedienungsanleitung

AEG

AEG Protect A. 1000 Bedienungsanleitung

AEG

AEG PROTECT C. 1000 (S) Bedienungsanleitung

AEG

AEG Protect C.R Bedienungsanleitung

AEG

AEG PROTECT C Series Bedienungsanleitung

AEG

AEG Protect B. 750 PRO Bedienungsanleitung

AEG

AEG Protect A Series Bedienungsanleitung

AEG

AEG Protect D Series Bedienungsanleitung

AEG

AEG PROTECT A. 500 Bedienungsanleitung

AEG

AEG Protect C 1000 LCD+ Bedienungsanleitung

AEG

AEG PROTECT 1 Series Bedienungsanleitung

AEG

AEG MBS 6000 Bedienungsanleitung

AEG

AEG Protect Home. 600 Bedienungsanleitung

AEG

AEG Fluxpower HE Series Installations- und Betriebshandbuch

AEG

AEG CompuMaster 300 Bedienungsanleitung

AEG

AEG Protect 2.33 2.0 Bedienungsanleitung

AEG

AEG 80 / 120 kVA Bedienungsanleitung

AEG

AEG Protect C.3000 Bedienungsanleitung

AEG

AEG Protect NAS Betriebsanleitung

AEG

AEG Protect D Series Bedienungsanleitung

AEG

AEG UPS 10 kVA Bedienungsanleitung

AEG

AEG Protect alpha. 1200 Bedienungsanleitung

AEG

AEG PROTECT 1 LCD Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung