AEMC 566 Bedienungsanleitung
TRMS LEAKAGE CURRENT
CLAMP-ON METER 566
ENGLISH User Manual
Statement of Compliance
Chauvin Arnoux
®
, Inc. d.b.a. AEMC
®
Instruments
certifies that this instrument has been calibrated
using standards and instruments traceable to
international standards.
We guarantee that at the time of shipping
your instrument has met its published
specifications.
An NIST traceable certificate may be
requested at the time of purchase, or
obtained by returning the instrument to our
repair and calibration facility, for a nominal
charge.
The recommended calibration interval for
this instrument is 12 months and begins
on the date of receipt by the customer. For
recalibration, please use our calibration
services. Refer to our repair and calibration
section at www.aemc.com.
Serial #: _____________________________
Catalog #: 2139.83
Model #: 566
Please fill in the appropriate date as indicated:
Date Received: _________________________
Date Calibration Due: ____________________
Chauvin Arnoux®, Inc. d.b.a AEMC®Instruments
www.aemc.com
Clamp-on Meter Model 566
i
Table of Contents
1. INTRODUCTION ....................................1
1.1 International Electrical Symbols.............2
1.2 Receiving Your Shipment .......................2
1.3 Ordering Information ..............................2
2. PRODUCT FEATURES...........................3
2.1 Description .............................................3
2.2 Model 566 Control Features...................4
2.3 LCD Display ...........................................5
2.4 Button Functions ....................................6
2.4.1 HOLD / LPF Button ...................6
2.4.2 PEAK / Ω Button...................6
2.4.3 ZERO (Relative) Button.............7
2.4.4 Backlight Button ........................7
2.4.5 Auto-OFF...................................7
3. SPECIFICATIONS..................................8
3.1 Electrical Specications .........................8
3.2 Mechanical Specications....................10
3.3 Environmental Specications...............10
3.4 Safety Specications............................10
4. OPERATION ........................................11
4.1 Precautions Before Use .......................11
4.2 AC Current Measurement ....................12
4.3 AC Voltage Measurement ....................14
4.4 DC Voltage Measurement....................15
4.5 Resistance Measurement ....................16
4.6 Continuity Measurement ......................17
ii
Clamp-on Meter Model 566
5. MAINTENANCE ...................................20
5.1 Warning................................................20
5.2 Cleaning...............................................20
5.3 Battery Replacement............................21
Repair and Calibration........................................22
Technical and Sales Assistance .........................22
Limited Warranty ................................................23
Warranty Repairs................................................23
Clamp-on Meter Model 566
1
CHAPTER 1
INTRODUCTION
Warning
• Read the user manual before operating and
follow all safety information.
• Only use the meter as specied in this user
manual.
• Never use this meter on a circuit with volt-
ages greater than 600Vrms @ 50/60Hz.
• Never measure current while the test leads
are connected to the input jacks.
• Do not operate the meter if the case or
tests leads look damaged.
• Only use factory supplied leads.
• Check the rotary range switch and make
sure it is at the correct position before each
measurement.
• Do not perform resistance and continuity
test on a live circuit.
• Use extreme caution when measuring live
systems with voltages greater than 60VDC
or 30VAC.
• Use extreme care when working around
bus bars and bare conductors.
• Do not use the meter in over range/over-
load conditions (OL).
• For accurate readings, change the battery
when the symbol appears.
2
Clamp-on Meter Model 566
1.1 International Electrical Symbols
This symbol signies that the instrument is
prtected by double or reinforced insulation.
WARNING - refer to this manual for instructions
before operating the instrument. This symbol
indicates that if the instructions are not followed,
bodily injury, installation/sample and product
damage may result.
Risk of electric shock. The voltage at the parts
marked with this symbol may be dangerous.
Do not operate within external low frequency
magnetic elds >30A/m.
1.2 Receiving Your Shipment
Upon receiving your shipment, make sure that the
contents are consistent with the packing list. Notify
your distributor of any missing items. If the equipment
appears to be damaged, le a claim immediately with
the carrier and notify your distributor at once, giving a
detailed description of any damage. Save the damaged
packing container to substantiate your claim.
1.3 Ordering Information
TRMS Clamp-on Leakage Current
Meter Model 566....................................... Cat. #2139.83
Includes meter, test leads, two 1.5V AAA (LR03)
batteries, soft carrying case and user manual.
1.3.1 Accessories and Replacement Parts
Replacement Pouch .................................. Cat. #2118.94
AC Line Splitter Model ALS-1.................... Cat. #2121.05
Leads, set of 2 w/4mm right angle plugs... Cat. #2154.74
Clamp-on Meter Model 566
3
CHAPTER 2
PRODUCT FEATURES
2.1 Description
The TRMS Clamp-on Meter Model 566 is designed to
measure low AC currents, which are typically leakage
currents in ground conductors. Low currents are
measured in the 60mA and 600mA ranges. Note the high
sensitivity of the probe: 1uA, 10uA, and 100uA resolution
when measuring mA. This is possible through special
jaw construction and in particular critical shielding of the
jaws. At low measurement levels, shielding out noise is
critical for low sensitivity, accuracy and stability.
Leakage current may be measured on a ground
conductor and through the vector sum on multi-
conductors. On a grounded system, clamp around the
two or three conducting legs (not the ground conductor).
The vector sum of the load currents will cancel out,
leaving the leakage current measured.
You can also use the Model 566 as a standard clamp-on
meter to 60Arms, plus standard VAC, VDC ranges,
resistance and continuity with a buzzer. In mAAC and
AAC, the user can activate a low-pass lter (LPF) to
ignore all currents other than 50/60Hz. In this mode, only
the fundamental signal is measured.
The Model 566 is ergonomic in design and ts well in the
hand. Also, one hand operation is possible. The jaw size
is compact yet designed to accommodate most known
ground conductors up to 0.91" (23mm) in diameter.
4
Clamp-on Meter Model 566
2.2 Model 566 Control Features
A
I N S
E
T R U M
M
EN T
C
S
M
O
D
E
L
5
6
6
1. Jaw assembly (Ø 0.91", 23mm)
2. Safety barrier anti-slip guard
3. Backlight button
4. Jaw trigger for jaw opening/closing
5. Function select rotary dial
6. ZERO button
7. PEAK / Ωbutton
8. HOLD / LPF button
9. LCD display
10. COM (Black) input terminal jack
11. Positive (Red) input terminal jack
Clamp-on Meter Model 566
5
2.3 LCD Display
Auto-o indicator
Polarity indicator
Low battery indicator
AC measurement indicator
DC measurement indicator
ACurrent measurement indicator
VVoltage measurement indicator
ZERO Zero indicator
HOLD Data hold indicator
PEAK Peak hold indicator
Low pass lter indicator
Continuity test indicator
KMeasurement unit
ΩResistance measurement indicator
mMeasurement unit
6
Clamp-on Meter Model 566
2.4 Button Functions
2.4.1 HOLD / LPF Button
This button has two functions, HOLD and LPF (Low
Pass Filter).
HOLD
This function locks (holds) the measurement currently
displayed on the LCD.
1. To activate, press the HOLD button during the
measurement. The HOLD symbol appears and the
measurement is locked.
2. To deactivate, press the HOLD button again.
LPF (Low Pass Filter)
The cut-o frequency of the low pass lter is approxi-
mately 60Hz with an attenuation characteristic of
approximately -24dB/octave.
1. To activate the LPF feature, press and hold down the
HOLD button for approximately 2 seconds until the
symbol appears on the LCD.
2. To deactivate, press and hold down the button again
for approximately 2 seconds. The meter will return to
normal operation mode.
Note: This feature is active when the rotary switch is set
to AAC or mAAC.
2.4.2 PEAK / Ω Button
1. Press the PEAK button to enter PEAK mode. In this
mode the instrument records the peak maximum
value. Press PEAK again to return to normal mode.
2. With the rotary switch set to Ω, press PEAK to
enter resistance measurement mode. Press PEAK a
second time to enter continuity test mode.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere AEMC Messgerät Handbücher
AEMC
AEMC 6240 Bedienungsanleitung
AEMC
AEMC MN353 Bedienungsanleitung
AEMC
AEMC MD304 Bedienungsanleitung
AEMC
AEMC MN124 Bedienungsanleitung
AEMC
AEMC MN213 Bedienungsanleitung
AEMC
AEMC 1821 Bedienungsanleitung
AEMC
AEMC PowerPad IV Bedienungsanleitung
AEMC
AEMC JM830A Bedienungsanleitung
AEMC
AEMC 5600 Bedienungsanleitung
AEMC
AEMC 601 Bedienungsanleitung
AEMC
AEMC 6292 Gebrauchs- und Pflegehandbuch
AEMC
AEMC MN170 Bedienungsanleitung
AEMC
AEMC MR561 Bedienungsanleitung
AEMC
AEMC 1510 Bedienungsanleitung
AEMC
AEMC A196-24-BK Bedienungsanleitung
AEMC
AEMC SL261 Bedienungsanleitung
AEMC
AEMC 500 Bedienungsanleitung
AEMC
AEMC Model 6292 Bedienungsanleitung
AEMC
AEMC 3910 Bedienungsanleitung
AEMC
AEMC 6526 Bedienungsanleitung
