Aesthetix IO Bedienungsanleitung

Io with Volume Controls

Two Phono Inputs

Important Note One: Never change phono inputs with the volume controls up. Always ensure

the volume controls are at their minimum (fully counter-clockwise) setting before changing

inputs. Unless the volume controls are at their minimum setting, a loud discharge will occur

that can potentially damage speakers.

An Io with volume controls configured with two phono inputs has four Aux. Input boards (one for left, one

for right, for each input) shown at the rear of the unit in the below photo (right).

The picture below shows a close-up of the phono

Aux. Input board.

If the load setting is the same for both cartridges (inputs) the rear panel jumpers can be used to set the

global load value. In this case, the load jumpers (red arrow in the above left picture) will not be used.

If the 2 cartridges (inputs) require different load values, use only the load jumpers on the internal 4

boards, and remove all jumpers from the rear panel.

When different load settings are required for each input, the red arrow indicates where the user will install

a loading jumper. If a load of 47K* is desired, do not install any jumpers. The other possible values are:

10K, 4.7K, 2.5K, 1K, 750 ohms, 475 ohms, 375 ohms, 250 ohms, 200 ohms and 150 ohms.

On each input, both channels (left and right) should be set to the same load value. There are four

jumpers in total. These are most easily changed with needle-nose pliers or tweezers.

*Factory default setting

Important Note Two: Never change the below settings with the Io on. Always turn off the Io

and wait 20 minutes before altering internal settings. This allows the power supplies to fully

discharge. If in doubt, refer to your qualified Aesthetix dealer or the factory.

Important note: Unless updated, older units did not have the Aux Input boards. Those units can

be upgraded by having the Aux Input boards installed.

Rev 1.20 2019-11-27

The blue arrow points to a 2 position jumper setting used to select a floating or grounded input for the

RCA connector. As a phono input, it should be set to FLT, or its upper position.

The black arrow points to the BAL/SE jumper setting. In almost all cases, this should be set to BAL,

regardless of whether RCA or XLR input jacks are used.

Not all system configurations are the same. In the event of hum on the phono input(s), other

combinations can be tried. However, the above factory defaults should be ideal for nearly every system.

GND

-OUT

+OUT

BAL

FLT Load Value

Aux Input board phono section block diagram

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Aesthetix Phono-Vorstufe Handbücher

Aesthetix

Aesthetix IO Bedienungsanleitung

Beliebte Phono-Vorstufe Handbücher anderer Marken

ANK

ANK L5 Gebrauchsanweisung

Musical Fidelity

Musical Fidelity M3X VINYL Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box S3 B Bedienungsanleitung

Lehmannaudio

Lehmannaudio Black Cube Statement Bedienungsanleitung

T+A

T+A R 2000 Series Bedienungsanleitung

Caledonian Audio

Caledonian Audio Phono Classique Bedienungsanleitung

Clearaudio

Clearaudio Absolute phono Bedienungsanleitung

DSA

DSA Phono III Bedienungsanleitung

Well Tempered Lab

Well Tempered Lab RIAA Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box Design Tube Box DS2 Bedienungsanleitung

Cary Audio Design

Cary Audio Design VT-500 Bedienungsanleitung

ALLNIC AUDIO

ALLNIC AUDIO H-3000V Bedienungsanleitung

Phasemation

Phasemation EA-320 Bedienungsanleitung

RSL

RSL Phono-Stage Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems BOX-DESIGN Tube Box S2 Bedienungsanleitung

Rega

Rega FONO MM MK5 Bedienungsanleitung

Phasemation

Phasemation EA-300 Bedienungsanleitung

Chord

Chord SYMPHONIC Bedienungsanleitung