Afikim Superlight SL-3 Bedienungsanleitung
________________________________________________________2
WARNING
Read the User’s Manual carefully before operating the Superlight.
If you do not fully understand any part of this Manual,
Please contact your dealer or any of our Service.
Read this manual step by step
Centers - as injury or damage may occur from misuse!
WARNING
Electromagnetic Interference (“EMI”) can cause powered vehicles
to behave erratically, which could be dangerous to the user.
For your safety and protection, it is IMPERATIVE that you take
time to read Chapter : "EMI WARNING” before operating the
Superlight .
Serial Number Label is affixed to the Tiller: See Fig 10.
CE CERTIFICATION
The Afikim Electric Vehicles Ref. Registration Number with the
Competent Authority (UK)
is: CA 000292.
Our Authorized Representative with the
Competent Authorities is:
MEDES LTD.POB 231
Stanmore, Middlesex, HA7 4YA, England
TEL/FAX: 0044-181-954-9964
EDITION: 02
MODEL: SL-3
DATE: July 28, 2004
Cat. No. – PRSL001
I:\SL-3\WORD FILES\user manual sl3\User Manual SL3-ver5.DOC
________________________________________________________3
CONTENTS
Subject Page
CHAPTER 1 - DELIVERY and UNPACKING ........................................ 3
CHAPTER 2 - ASSEMBLY..................................................................5
CHAPTER 3 - OPERATING INSTRUCTIONS ................................... 12
CHAPTER 4 - DISASSEMBLY...........................................................16
CHAPTER 5 - CHARGING BATTERIES............................................. 19
CHAPTER 6 - STORING IN CAR........................................................21
CHAPTER 7 - TROUBLESHOOTING................................................22
BATTERY CHARGER - TROUBLESHOOTING..................................23
CHAPTER 8 - SAFETY INSTRUCTIONS ......................................... 24
CHAPTER 9 - SERVICE..................................................................... 26
CHAPTER 10 - SPECIFICATIONS *..................................................28
CHAPTER 11 - EMI WARNING.......................................................... 30
________________________________________________________4
CHAPTER 1 - DELIVERY and UNPACKING
The SUPERLIGHT Scooter is delivered to you
packed in one Cardboard Box. .
Note: The box weight 60kg (132 lb.) - do NOT attempt to
lift it with out assistance.
1.1 Unpack as follows (See Fig. 1)
a. Place boxes on floor with side up as marked by
the arrows on the side of the box.
b. Cut the Plastic Bands.
c. Remove the cardboard Top Cover.
d. Remove all parts from the boxes (and lay on the floor)
e. Identifying the SUPERLIGHT Components (See Fig. 1)
(1) Batteries Cover (2) Frame
(3) Seat (4) Batteries (left & right)
(5) Charger (6) Seat Adapter
(7) Tiller (8) Rear Basket
(9) Power Unit
Figure 1
________________________________________________________5
CHAPTER 2 - ASSEMBLY
2.1 Installation of the Power Unit
a. Position the Superlight power Unit on the floor so that the
anti tip is backward direction.
b. Lay the frame at the front of the power unit (See figure 2)
c. Lift the frame and install the frame bracket onto to power
unit square connecting bracket. Make sure the frame is
down to the end of the bracket. (See figure 3)
figure 2 figure 3
d. Secure the frame to the power unit by the anti tip securing
arrangement. Do that by releasing the knob at the right of
anti tip and pulling it upward until the knob is re secured.
(See figure 4)
figure 4 figure 4a
________________________________________________________6
e. To assure that the power unit is properly connected to the
frame ,you can try and lift the frame.
f. Connect the electrical connector coming from the frame to
the power unit Socket (See figure 4a) .
WARNING
After installing the frame onto the power unit and
locking it, Please check carefully that it is properly
positioned and secured.
2.2 Joining Tiller to Frame.
a. Place Tiller in front of the Frame. (See Fig. 5).
Kneel at the left side of the SUPERLIGHT holding the
left side of the Top Handle Bars of the Tiller with your
left hand. The Tiller should be vertical and slightly
inclined backward as shown in Figure 5.
b. With your right hand lift the Housing (at the front end of
the Frame) and place it above the (black) Tapered Pin
mounted on the Tiller.
c. Let the Housing slide down onto the black Tapered Pin
until you hear a “click”: at this time the Retaining Spring
should engage the Groove on the Tapered Pin thus
locking both sections to each other.
Figure 5
________________________________________________________7
d. Connect the Electric Plug to the Socket in the
Tiller (See Figure 6).
figure 6
2.3 Installation of Batteries (See Fig. 7)
Note: Installation of L.H Battery is identical to R.H.
Battery. L.H. Battery is shown.
a. Place battery in its location on the frame.
b. Connect Battery Plugs to battery.
Figure 7 – Small Battery Figure 8 – Large Battery
________________________________________________________8
2.4 Installation of Batteries Cover (See Fig. 9)
a. Place Batteries Cover over the Batteries .
Make sure to insert the rear plates under the
cover into the slots in the power unit and that the
front of the cover seat properly.
(See Figure 9)
Figure 9
c. Push the Plastic Clip to secure the Batteries
Cover in its location (See Figure 10).
Figure 10
________________________________________________________9
2.5 Seat Installation (Figure 11)
Seat Installation and Adjust:
a. Insert the Seat Adapter into the Seat-Bushing
(1) Verify that the Seat-Bushing slot is in forward direction.
(2) Install bolt and washer and tighten the bolts very well,
using the attached wrench.
(3) Install and tighten the securing nut very well, using attached
wrench.
(4) Install the Seat into the Seat-Bushing while the Seat is 45
degree to the side of the frame.
(5) Press the Seat Turning Lever to place the Seat forward
position.
b. Adjusting the height of the Seat
Remove nut,
bolt and washer.
Change the
Seat Adapter
height,
install, bolt and
washer and
tight strongly
the securing nut.
c. Install Seat
Upholstery.
Figure 11
________________________________________________________10
2.6 Rear Basket Installation
a. Install the Rear Basket by placing it on the two Upper
Support bracket at the rear of the seat back lying on
the Bottom Support. (See Fig. 12).
Figure 12
2.7 After the assembly make sure that:
a. All parts are undamaged, properly assembled
and secured.
b. All electrical plugs are properly fastened.
c. The operating levers return automatically to
center position when they are squeezed and
released.
It is recommended to charge the batteries overnight before
operating the SUPERLIGHT for the first time. See Chapter 5
for charging instructions.
Inhaltsverzeichnis
Andere Afikim Roller Handbücher
Afikim
Afikim Breeze-C Bedienungsanleitung
Afikim
Afikim Caddy Bedienungsanleitung
Afikim
Afikim Breeze S3 Bedienungsanleitung
Afikim
Afikim SPORTSTER SE Bedienungsanleitung
Afikim
Afikim Breeze Bedienungsanleitung
Afikim
Afikim afiscooter-s Bedienungsanleitung
Afikim
Afikim SE Bedienungsanleitung
Afikim
Afikim Afiscooter-M Bedienungsanleitung
Afikim
Afikim Breeze-S3 Bedienungsanleitung
Afikim
Afikim Breeze Bedienungsanleitung
Beliebte Roller Handbücher anderer Marken
First Choice Mobility
First Choice Mobility Roma Medical Corella S741 Bedienungsanleitung
Carrera
Carrera impel Bedienungsanleitung
CareCo
CareCo ZOOM Bedienungsanleitung
Douglas
Douglas Vespa G.S. Bedienungsanleitung
Gazelle
Gazelle with BOSCH System Bedienungsanleitung
Wisper
Wisper 806fe Bedienungsanleitung