AGCO DynaFlex Series Service-Handbuch

HeaderSettings Guide

DynaFlex&CommandSeries

Table of Contents

DynaFlex Settings Guide Procedure……………………………………….…..pg.2

Field Ready Setup…………………………………………………………..…….pg.3

Recommended Pressure Setting……………………………………………..…pg.17

End SkidAlignment………………………………………………………………..pg.19

Guard AngleSetting……………………………………………………………….pg.22

Header Height Setting…………………………………………………………….pg.25

Automatic Header Height Control………………………………………………..pg.27

Trouble Shooting…………………………………............................................... pg.30

3300 Command Series Settings………………………………………………...pg.40

3300 Command Adjustments………………………….....................................pg.47

3300 Command Series Options……………………….....................................pg.54

Notes………………………………………………………………………………..pg.58

DynaFlex Settings Guide Procedure

1. Ensure DynaFlex is fieldready

2. Set to recommendedpressure

3. Align end skid parallel to theground

4. Confirm guard angle is acceptable and adjust if necessary

5. Set header height to recommended targetheight

6. Fine-tune automatic header height controlsystem

Tilt Arm Pin Location

Pins are located at the rear of the headeron

each of the vertical support beams. There

are 16 total pins on a 40’ DynaFlexheader.

Relocate the pins from the front hole tothe

rear location to allow the tilt arms tofloat.

Electrical Harness Connection

Flex Mode Operation

–To utilize the cutterbar

potentiometers, connectthe

header main harness (1) to

the header control module

(2).

Rigid Mode Operation

–To utilize the drag rod

potentiometers, connectthe

header main harness (1) to

the jumper harness(3).

Electrical Harness Connection

Flex Mode Operation

–The potentiometer is

connected to the tilt armvia

a small armature rod. Ifthe

cutterbar encounters a

change in contour, the tilt

arm will move accordingly

and change the voltage

reading within the

potentiometer. The header

height control system’s

function is to maintain a

target voltage reading and

will raise or lower the

header to achieve the

targetsetting.

Electrical Harness Connection

Rigid Mode Operation

–The potentiometer is attached

to a drag rod that hangs down

on each end of the header. If

the drag rod encounters a

change in contour, the voltage

reading will change in the

potentiometer and the header

height control system will react

to maintain the target setheight

selected by the operator. Drag

rods are most commonly used

in small grains in Auto Tilt

mode which automatically tilts

the platform from side to side

and the operator manually

controls the header raise and

lower.

Reel Height Adjustment

To correctly set the reel height, reduce

the cutterbar pressure to 400 –500 PSI

and pitch the header all the way forward

to -6. Place a 4x4 block under the

cutterbar and lower the header firmly to

the ground.

Lower the reel to the minimum height

setting and adjust the reel fore/aft until

the reel is centered over the cutterbar.

Manually lower the reel by adjusting the

lift cylinder adjustment nut until a

minimum gap of 1.5” is achieved

between the highest point on the

cutterbar and the reel finger tine.

Reel Tine Pitch Adjustment

To manually adjust the pitch of the reel tines, loosen the 3 bolts on the adjustment lever located

on the right hand reel arm assembly and slide the handle to the desired setting. The adjustment

lever will be in the middle of the adjustment range as a factory configuration. The reel tubes on

the DynaFlex are mountedon a cam slide track which allows the individual reel tube tines to “flip

over” independent of each other. Different harvest conditions can warrant a change in tine pitch,

for example harvesting down lodged crop vs harvesting tall, standing crop. As an initial

setting, it is recommended to set the tine pitch to be vertically straight up and down on

the back side of the reel rotation.

Vertically

straight up and

down

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AGCO Landwirtschaftliche Geräte Handbücher

AGCO

AGCO Glencoe CP40 CULTIPACKER Bedienungsanleitung

AGCO

AGCO TG9300B Bedienungsanleitung

AGCO

AGCO Challenger Terra Gator 3244 Bedienungsanleitung

AGCO

AGCO Laverda Combines M400 Bedienungsanleitung

AGCO

AGCO Glencoe DR8700 Bedienungsanleitung

AGCO

AGCO LELY ATTIS PT 130 Bedienungsanleitung

AGCO

AGCO Gleaner 3200 Series Bedienungsanleitung

AGCO

AGCO FENDT 9490 x Bedienungsanleitung

AGCO

AGCO FENDT 5250L Gebrauchsanweisung

AGCO

AGCO Massey Ferguson 9702 Bedienungsanleitung

AGCO

AGCO Glencoe SS7400 Soil Saver Bedienungsanleitung

AGCO

AGCO GSI 54 Bedienungsanleitung

AGCO

AGCO FENDT Bedienungsanleitung

AGCO

AGCO FENDT CARGO Bedienungsanleitung

AGCO

AGCO 1800 Series Betriebsanleitung

AGCO

AGCO Combine CEREA 7274 Bedienungsanleitung

AGCO

AGCO Massey Ferguson 8516 Bedienungsanleitung

AGCO

AGCO HayBoss G2 596 Bedienungsanleitung

AGCO

AGCO Glencoe SS7400 Soil Saver Bedienungsanleitung

AGCO

AGCO FENDT 700 Vario SCR Stage 3B Bedienungsanleitung

AGCO

AGCO GSI PNEG-1826 Bedienungsanleitung

AGCO

AGCO FENDT 9300R Bedienungsanleitung

AGCO

AGCO Glencoe ULTRAMULCHER UM43 21' Bedienungsanleitung

AGCO

AGCO VALTRA MOMENTUM Series Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung