AGI A114 Bedienungsanleitung

30798 R1

Revised: APRIL 2021 1

A114

Swivel Arc Kit

Assembly and Operator Manual

Applicable Models:

•Westfield WR6, WRX 8/10 Series

•AGI WRX 8/10 Series

•Hutchinson WR6, WRX 8/10 Series

•Mayrath WR6, WRX 8/10 Series

Assembling the Swivel Arc Kit

1. Securely chock wheel on one side of auger.

2. Jack up other wheel and place sturdy support underneath axle close to wheel. Lower weight of auger onto

this support.

3. Remove wheel and hub assembly from spindle. Keep dirt out of hub bearings and grease.

4. Place appropriate left or right swivel kit arm (A) onto spindle (see ). Secure arm with 3/4" slotted nut.

Tighten snug only. Insert cotter pin.

Note

To determine left or right side of a grain auger, stand at intake end facing upper discharge end.

5. Loosely install brackets (B) and (C) to lower undercarriage tubes next to bracket (D) where upper lift arms

are attached. Use two 7/16" x 1" bolts and locknuts and two 7/16" x 3-1/2" or 4" bolts and locknuts.

6. Secure adjust strap (E) to bracket (B) and to swivel arm (A) with two 1/2" x 1-1/4" bolts and locknuts. Adjust

the angle of the wheel with this adjust strap. Securely tighten all bolts installed in Steps 5 and 6.

Note

Since most bin installations require one basic auger height, the angle of the wheels should be

adjusted once this height is determined. To change the angle of the wheels, see below.

7. Secure wheel spindle bracket (F) to arm (A). Tighten securely with 3/4" nut and lockwasher.

2 30798 R1

Figure 1. Assembling the Swivel Arc Kit

8. Assemble hub. First remove dirt and paint from spindle. Wheel bearings should be thoroughly packed with a

high-quality SAE-approved bearing grease. Place hub on spindle, insert small wheel bearing, then tighten 3/

4" slotted nut until hub drags slightly. Back off nut about 1/4 turn until hub turns freely. Install cotter pin

and dust cap.

9. Attach auger wheel to hub with four wheel bolts. Tighten securely. Jack up axle, remove support and lower

jack.

10. Repeat above procedure on other wheel.

Changing the Angle of the Wheels

1. Jack up the axle.

2. Place safety support under axle.

3. Remove the lower 1/2" x 1-1/4" bolt on the adjust strap (E) and change the angle of the wheel as desired.

4. Replace and secure the bolt and locknut.

5. Remove the axle support and jack.

6. Repeat on other wheel.

Changing the Wheel from Swivel to Transport

Or changing the wheel from Transport Position to Swivel Position

1. Jack up the axle.

2. Place the safety support under the axle.

A114 SWIVEL ARC KIT –

30798 R1 3

3. Loosen the 3/4" nut (G) on the swivel arm (A).

4. Change the position of the wheel and re-tighten the 3/4" nut.

5. Remove the axle support and jack.

6. Repeat on other wheel.

Note

If the auger must be transported on the road for any considerable distance at speeds higher than 10

mph (16 km/h), the wheels and hub assemblies should be re-installed on the auger axle spindle.

Note

When moving the auger sideways in the swivel arc position, make certain the area is level and free of

debris. Holes and bumps may cause the auger to upset.

Figure 2. Equipment Decals

P.O. Box 39

Rosenort, Manitoba, R0G 1W0 Canada Website: www.aggrowth.com

Phone: (866) 467-7207 (Canada & USA) or (204) 746–2396 Email: [email protected]

Fax: (866) 768-4852 ©Ag Growth International Inc. 2021, Printed in Canada

A114 SWIVEL ARC KIT –

Inhaltsverzeichnis

Andere AGI Landwirtschaftliche Geräte Handbücher

AGI

AGI Batco BCX21544 Bedienungsanleitung

AGI

AGI NECO Series Montage- und Bedienungsanleitung

AGI

AGI Westfield MKX10-63 Bedienungsanleitung

AGI

AGI Westeel EasyFlow2 100 Series Bedienungsanleitung

AGI

AGI Wheatheart X160-85 Montageanleitung

AGI

AGI MKX2 Series Bedienungsanleitung

AGI

AGI STORM Professional 2020 Series Bedienungsanleitung

AGI

AGI Storm Professional 2017 Series Bedienungsanleitung

AGI

AGI WRX Series Bedienungsanleitung

AGI

AGI Batco BCX2 Bedienungsanleitung

AGI

AGI WESTEEL 100 Series Bedienungsanleitung

AGI

AGI Westfield MKX 13-64 Bedienungsanleitung

AGI

AGI GRAINMAXX 6300 Series Bedienungsanleitung

AGI

AGI Batco 1200 Series Bedienungsanleitung

AGI

AGI STORM FX2 Series Bedienungsanleitung

AGI

AGI WHEATHEART X Series Montage- und Bedienungsanleitung

AGI

AGI Batco BCX2 1500 Series Bedienungsanleitung

AGI

AGI Batco FX 1500 Series Bedienungsanleitung

AGI

AGI Westfield MKX10-53 Bedienungsanleitung

AGI

AGI C-Line Bedienungsanleitung

AGI

AGI 15 Series Bedienungsanleitung

AGI

AGI Batco BCX2 1544 Bedienungsanleitung

AGI

AGI Westfield Leitfaden

AGI

AGI MKX2 Series Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung