Agilent Technologies G4239C Bedienungsanleitung
Agilent Technologies
Agilent G4239C Valve Kit -
Instructions
Agilent G4239C Valve Kit - Instructions
Technical Information about the Agilent Valve Kit G4239C.
Contents
Typical Applications 2
Multicolumn Selection 2
Method Development 3
Delivery Checklist 4
Install the Valve Heads 5
Remove the Transportation Lock and the Valve Dummy 5
Install the Valve Head and Connect Capillaries 6
Install the Capillaries 8
Setup Examples 10
Valve Specifications 11
Valve Parts 11
2
Typical Applications
Multicolumn Selection
Typical Applications
Multicolumn Selection
Advantages
•Increase productivity
•Higher instrument up- time
Quickly change between up to eight different stationary phases for different
applications, or use identical stationary phases in columns with different
dimensions for either faster run- times (short columns) or higher resolution (long
columns) or for loading studies with different internal diameters.
Figure 1 The G7116B 1290 Infinity II Series Multiple Column Thermostat equipped with an
8 Column Selector Valve
3
Typical Applications
Method Development
Method Development
Advantages:
•Faster method development
•Automated method development possible
b6J
%
&%
'%
'%
'%
&%
&%
%
%
%#* & &#* ' '#* ( (#* b^c
:Xa^ehZeajhE]Zcna=Zmna
:Xaa^ehZeajh8&-
7dcjhGE
%#* & &#* ' '#* ( (#*
%#* & &#* ' '#* ( (#*
b^c
b^c
Figure 2 Totally different chromatographic results by using the same sample but three different
stationary phases
4
Delivery Checklist
Method Development
Delivery Checklist
Delivery Checklist
p/n Description
5067-4233 8 Column Selector, 1300 bar
G4239C
5067-4248 Capillary Kit, 0.12 mm, 8-column sel. PCHex (OPTIONAL)
Capillary Kit
(5067-4248) # p/n Description
15500-1202 Capillary SST 0.12x500mm M4-SL PS-PS
Autosampler to valve
85500-1199 Capillary SST 0.12x130mm M4-SL PS-PS
Valve to heat exchanger
15500-1200 Capillary SST 0.12x130mm M4 PS-NS LS
Column to valve
15063-6591 PEEK Fittings 10/PK
Column outlet
85500-1201 Capillary SST 0.12x105mm SL-- PS-LS
Heat exchanger (ps-SL) to column (long socket - use G1314-68703)
8G1314-68703 Cap fitting kit special
Column inlet connection fitting
15500-1203 Capillary SST 0.12x280mm M4-SL PS-PS
Valve (ps-M4) to detector (ps-SL)
15500-1204 Capillary SST 0.12x150mm M4-M4 PS-PS
Valve to valve (column bypass)
15023-2504 Hex driver SW-4 slitted
Tool for M4 fittings
8G7116-60015 Heat Exchanger Assembly 1.6 µL-Z Quick Connect Heatexchanger
Standard Flow
Low dispersion heat exchangers
1G1375-87326 Waste tube
Waste tube incl. M4 PEEK fitting
35067-6141 M4 Blank nut
for plugging unused valve ports
8G7116-68003 Column Holder Clips (2/Pk) for G7116B
Capillary & Fitting Information
•M4 = fitting thread size for micro valve ports
•PS = pre- swaged fitting
•NS = non- swaged fitting
•SL = fitting screw long
•LS = long capillary socket (required for special fittings as the A- Line Quick
Turn Fittings)
5
Install the Valve Heads
Remove the Transportation Lock and the Valve Dummy
Install the Valve Heads
The valve drives are factory- installed in the 1290 Infinity II Multicolumn
Thermostat. The valve heads are interchangeable and can be easily mounted.
At the first installation, the transportation lock and the dummy valve have to be
removed, see “Remove the Transportation Lock and the Valve Dummy” on page 5.
The valve heads can be installed by mounting the valve heads onto the valve
drives and fastening the nut manually (do not use any tools).
Be sure that the guide pin snaps into the groove of the valve drive thread.
1When unscrewing the transportation lock, push it back until the
last screw is removed - the valve rail is spring-loaded.
2Press on the valve dummy to release it (spring-loaded valve
rail).
&#
'#
3 4
Remove the Transportation Lock and the Valve Dummy
NOTE
Following procedures may show the 1290 Infinity TCC. The MCT uses the same valve heads, the
valve head installation is the same.
NOTE
The valves are mounted on pull-out rails to allow easy installation of capillaries. Push the valve
gently into its housing until it snaps into the inner position, push it again and it slides out.
When all capillaries are installed, push the valve back into its housing, see “Install the Valve Head
and Connect Capillaries” on page 6.
The valve actuator contains sensitive optical parts, which need to be protected from dust and
other pollutions. Pollution of these parts can impair the accurate selection of valve ports and
therefore bias measurement results.
➔Always install a valve head for operation and storage. For protecting the actuator, a dummy
valve head can be used instead of a functional valve. Do not touch parts inside the actuator.
Column Damage or Bias Measurement Results
Switching the valve to a wrong position can damage the column or bias measurement results.
➔Fit the lobe to the groove to make sure the valve is switched to the correct position.
Valve Damage
Using a low pressure valve on the high pressure side can damage the valve.
➔When using multiple column compartments as part of a method development solution, make
sure that the high pressure valve head is connected to the autosampler and the low pressure
valve head is connected to the detector.
6
Install the Valve Heads
Install the Valve Head and Connect Capillaries
Install the Valve Head and Connect Capillaries
CAUTION
CAUTION
CAUTION
NOTE
For a correct installation of the valve head, the outside pin (red) must completely fit into the outside
groove on the valve drive’s shaft (red). A correct installation is only possible if the two pins (green
and blue) on the valve head fit into their corresponding grooves on the valve drive’s actuator axis.
Their match depends on the diameter of the pin and groove.
7
Install the Valve Heads
Install the Valve Head and Connect Capillaries
1Insert the valve head into the valve shaft.
OR
If the outside pin does not fit into the outside groove, you have to
turn the valve head until you feel that the two pins snap into the
grooves. Now you should feel additional resistance from the valve
drive while continue turning the valve head until the pin fits into
the groove.
2When the outer pin is locked into the groove, manually screw
the nut onto the valve head.
NOTE
Fasten the nut manually. Do not use any tools.
8
Install the Capillaries
Install the Valve Head and Connect Capillaries
Install the Capillaries
3Install all required capillary connections to the valve. 4Push the valve head until it snaps in and stays in the rear
position.
5Power on or power-cycle your module, so the valve head gets recognized during module initialization.
Damage to the rotor seal
Instant pressure release within the valve will lead to water jet effects that can harm internal
parts of the valve. This pressure release typically happens if the valve gets switched under high
pressure over unused or open channels.
➔Block all unused channels properly with the M4 blank nut.
CAUTION
NOTE
To minimize valve movement over open connections it is recommended to plumb the column
connected channels in one row.
e.g.:
•channel 1 – column 1
•channel 2 – column 2
•channel 3 – column 3
•channel 4 – column 4
•channel 5 – blocked
•channel 6 – blocked
•channel 7 – waste
•channel 8 – bypass
NOTE
The blank nuts are only required for the ports on the inner circle that connect the valve with the
column inlet.
9
Install the Capillaries
Install the Valve Head and Connect Capillaries
1Install the in and out connectors.
•from sampler to the valve ( Capillary SST 0.12x500mm M4- SL PS- PS
(5500- 1202))
•from valve to the detector ( Capillary SST 0.12x280mm M4- SL PS- PS
(5500- 1203))
Dji
>c
The In port is hydraulically connected to the column inlet ports 1- 8 on the
inner ring while the Out port connects to the column outlet ports 1`-8` on the
outer ring.
2Install the column inlet and outlet connections.
ports 1-8 for connections from valve to the heat exchanger ( Capillary SST 0.12x130mm M4-SL PS-PS
(5500-1199)) or waste line (Waste tube (G1375-87326))
ports 1`-8` for connections from column outlet to valve ( Capillary SST 0.12x130mm M4-SL PS-NS LS
(5500-1200)), use fingertight PEEK fittings for connecting the column outlet
;gdbXdajbc
Id]ZVi
ZmX]Vc\Zg
10
Setup Examples
Install the Valve Head and Connect Capillaries
Setup Examples
18 Column- selection
Figure 3 Hydraulic flow path schematics for an 8-column selection setup
2Six column selection with purge line and valve- bypass
Figure 4 Hydraulic flow path schematics for 6-column selection setup with purge and valve
bypass line.
Inhaltsverzeichnis
Andere Agilent Technologies Steuereinheit Handbücher
Agilent Technologies
Agilent Technologies TwisTorr 305 FS Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies 8498A Service-Handbuch
Agilent Technologies
Agilent Technologies 1200 series Bedienungsanleitung
Agilent Technologies
Agilent Technologies E1339A Betriebsanleitung
Agilent Technologies
Agilent Technologies 81610A Bedienungsanleitung
Agilent Technologies
Agilent Technologies E2261A Betriebsanleitung
Agilent Technologies
Agilent Technologies 83481A Bedienungsanleitung
Agilent Technologies
Agilent Technologies LC Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies 34946A Bedienungsanleitung
Agilent Technologies
Agilent Technologies 81618A Bedienungsanleitung
Agilent Technologies
Agilent Technologies 83486A Bedienungsanleitung
Agilent Technologies
Agilent Technologies VXI 75000 C Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies G2623A Bedienungsanleitung
Agilent Technologies
Agilent Technologies 6850 GC Bedienungsanleitung
Agilent Technologies
Agilent Technologies VME VXI 75000 B Series Installations- und Betriebshandbuch
Agilent Technologies
Agilent Technologies 70341A Bedienungsanleitung
Agilent Technologies
Agilent Technologies TwisTorr Medium-TMP X3512-64016 Bedienungsanleitung
Agilent Technologies
Agilent Technologies NW16 Bedienungsanleitung
Agilent Technologies
Agilent Technologies 11713B Service-Handbuch
Agilent Technologies
Agilent Technologies 1100 Series Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
