Agilent Technologies N2757A Bedienungsanleitung

Agilent N2757A GPIB Interface Module

Publication number N2757-92001

Printed June 2000

$

Installation Guide

Introduction

he Agilent N2757A GPIB Interface Module provides remote

communication with fast data transfers and full programmability for the

following Agilent 54600-series Oscilloscopes:

54621A Oscilloscope

54621D Mixed-Signal Oscilloscope

54622A Oscilloscope

54622D Mixed-Signal Oscilloscope

54624A Oscilloscope

he GPIB port can be used for remote programming and to link your pc

to the oscilloscope when using the BenchLink XL 54600 connectivity

software. For programming specifics, refer to the 54600-series

Oscilloscope Programmer’s Guide shipped with your oscilloscope. For

connectivity, refer to the BenchLink XL 54600 software for complete

instructions.

he following are recommended GPIB cards you can purchase for your

pc.

Part number Description

82341C High-Performance GPIB Interface for Windows 3.1/95/98/NT

82341D High-Performance plug&play GPIB Interface for Windows 95/98

82350A PCI High-Performance GPIB Interface Card for Windows 95/98/NT

Installation Guide

To install the interface module

1Turn the oscilloscope power off.

2Insert the ta s on top of the module into the holes on the ack of the

oscilloscope as shown elow.

3Push the module down until the connector-aligning ta on the ack of

the module snaps into the alignment slot on the ack of the oscilloscope.

4Secure the module to the oscilloscope using the screw on the module.

QPFGU

Tabs

Screw

Alignment slot

Installation Guide

To connect the GPIB cable

To connect the GPIB ca le

Connect your GPIB cable to the GPIB module and to your pc/controller. he

following list shows recommended GPIB interface cables.

If you need additional clearance between the GPIB socket on the pc GPIB

interface card and the pc chassis you can purchase the 10834A GPIB adapter.

Part Number Cable length

10833A 1 meter

10833B 2 meters

10833D 0.5 meter

RFI shielding

The 10833 cables feature an improved shielding design to help reduce RFI levels in

systems. To further reduce RFI levels, the interface module is shipped with a clip-on

ferrite bead that you can attach to your GPIB cable. Lay the ferrite bead under the

GPIB cable as shown below, then snap the two halves of the ferrite bead together.

The ferrite bead should be attached as close to the interface module connection as

possible.

Note: shape of ferrite

bead may vary from

that pictured

Installation Guide

To verify the module is properly connected

1Turn the oscilloscope power on.

2Press the oscilloscope Utility key, then press the Service softkey.

3Press the About Oscilloscope softkey.

he Option Module: line should display as shown below.

Service softkey

About Oscilloscope

softkey

Installation Guide

To set the GPIB address

1Turn the oscilloscope power on.

2Press the oscilloscope Utility key, then press the I/O softkey.

3Press the Controller softkey and select GPIB.

4Turn the Entry kno to set the GPIB address. The selected address is

displayed in the Address softkey.

IO softkey

used for

RS-232 only Address

softkey

Controller

softkey

DECLARATION OF CONFORMITY

According to ISO/IEC Guide 22 and CEN//CENELEC EN 45014

Manufacturer’s Name: Agilent Technologies, Inc. / Digital Design PGU

Manufacturer’s Address: 1900 Garden of the Gods Road

Colorado Springs, CO 80907, U.S.A.

Declares, that the product

Product Name: Digitizing Oscilloscope Module

Model Number(s): N2757A

Product Option(s): This declaration covers all options of the above products(s)

Conforms to the following product standards:

EMC Standard Limit

IEC 61326-1:1997+A1:1998 / EN 61326-1:1997+A1:1998

CISPR 11:1990 / EN 55011:1991 Group 1, Class A [1]

IEC 61000-4-2:1995+A1:1998 / EN 61000-4-2:1995 4 kV CD, 8 kV AD

IEC 61000-4-3:1995 / EN 61000-4-3:1995 3 V/m, 80-1000 MHz

IEC 61000-4-4:1995 / EN 61000-4-4:1995 0.5 kV signal lines, 1 kV power Lines

IEC 61000-4-6:1996 / EN 61000-4-6:1996 3 V, 0.15-80 MHz

Canada: ICES-001:1998

Safety IEC 61010-1:1990+A1:1992+A2:1995 / EN 61010-1:1994+A2:1995

Canada: CSA C22.2 No. 1010:1:1992

Conformity / Supplementary Information:

The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and

the EMC Directive 89/336/EEC (including 93/68/EEC) and carries the CE-marking accordingly

(European Union)

[1] The product was tested in a typical configuration with Agilent Technologies test systems.

Date: 05/02/2000

For further information, please contact your local Agilent Technologies sales office, agent, or distributor.

Name

Ken Wyatt, Product Regulations Manager

Agilent echnologies

P.O. Box 2197

1900 Garden of the Gods Road

Colorado Springs, CO 80901

echnologies 2000

Reproduction, adaptation,

or translation without prior

written permission is

prohibited, except as

allowed under the copyright

laws.

Restricted Rights

Legend.

Use, duplication or

disclosure by the U.S.

Government is subject to

restrictions as set forth in

subparagraph (c) (1) (ii) of

the Rights in echnical Data

and Computer Software

clause at DFARS 252.227-

7013 for DOD agencies, and

subparagraphs (c) (1) and

Computer Software

Restricted Rights clause at

FAR 52.227-19 for other

agencies.

Agilent echnologies

3000 Hanover Street

Palo Alto, California 94304

U.S.A.

Document Warranty

he information contained

in this document is subject

to change without notice.

Agilent Technologies

makes no warranty of

any kind with regard to

this material including

but not limited to the

implied warranties of

merchantability or

fitness for a particular

purpose.

Agilent echnologies shall

not be liable for errors

contained herein or for

damages in connection with

the furnishing,

performance, or use of this

material.

Product Warranty

his Agilent echnologies

product has a warranty

against defects in material

and workmanship for a

period of 90 days from date

of shipment. During the

warranty period, Agilent

echnologies will, at its

option, either repair or

replace products that prove

to be defective.

For warranty service or

repair, this product must be

returned to a service facility

designated by Agilent

echnologies.

For products returned to

Agilent echnologies for

warranty service, the Buyer

shall prepay shipping

charges to Agilent

echnologies and Agilent

echnologies shall pay

shipping charges to return

the product to the Buyer.

However, the Buyer shall

pay all shipping charges,

duties, and taxes for

products returned to

Agilent echnologies from

another country.

Agilent echnologies

warrants that its software

and firmware designated by

Agilent echnologies for

use with an instrument will

execute its programming

instructions when properly

installed on that

instrument. Agilent

echnologies does not

warrant that the operation

of the instrument software,

or firmware will be

uninterrupted or error free.

Limitation of Warranty

he foregoing warranty

shall not apply to defects

resulting from improper or

inadequate maintenance by

the Buyer, Buyer-supplied

software or interfacing,

unauthorized modification

or misuse, operation outside

of the environmental

specifications for the

product, or improper site

preparation or

maintenance.

No other warranty is

expressed or implied.

Agilent Technologies

specifically disclaims the

implied warranties of

merchantability or

fitness for a particular

purpose.

Exclusive Remedies

he remedies provided

herein are the buyer’s sole

and exclusive remedies.

Agilent echnologies shall

not be liable for any direct,

indirect, special, incidental,

or consequential damages,

whether based on contract,

tort, or any other legal

theory.

Assistance

Product maintenance

agreements and other

customer assistance

agreements are available for

Agilent echnologies

products.

For any assistance, contact

your nearest Agilent

echnologies Sales Office.

Certification

Agilent echnologies

certifies that this product

met its published

specifications at the time of

shipment from the factory.

Agilent echnologies

further certifies that its

calibration measurements

are traceable to the United

States National Institute of

Standards and echnology,

to the extent allowed by the

Institute’s calibration

facility, and to the

calibration facilities of other

International Standards

Organization members.

Safety

his apparatus has been

designed and tested in

accordance with IEC

Publication 1010, Safety

Requirements for

Measuring Apparatus, and

has been supplied in a safe

condition. o ensure safe

operation and to keep the

product safe, the

information, cautions, and

warnings in this operating

manual must be heeded. In

addition, note the external

markings on the instrument

that are described under

"Safety Symbols."

Safety Symbols

Instruction manual symbol:

the product is marked with

this symbol when it is

necessary for you to refer to

the instruction manual in

order to protect against

damage to the product.

Hazardous voltage symbol.

Earth terminal symbol:

Used to indicate a circuit

common connected to

grounded chassis.

WARNING

he Warning sign denotes a

hazard. It calls attention to

a procedure, practice, or

the like, which, if not

correctly performed or

adhered to, could result in

personal injury. Do not

proceed beyond a Warning

sign until the indicated

conditions are fully

understood and met.

CAUTION

he Caution sign denotes a

hazard. It calls attention to

an operating procedure,

practice, or the like, which,

if not correctly performed

or adhered to, could result

in damage to or destruction

of part or all of the product.

Do not proceed beyond a

Caution symbol until the

indicated conditions are

fully understood or met.

About this edition

his is the Agilent N2757A

GPIB Interface Module

Installation Guide.

Publication number

N2757-92001, June 2000

Printed in USA.

Print history is as follows:

N2757-92001, June 2000

N2757-92000, April 2000

New editions are complete

revisions of the manual.

Many product updates do

not require manual

changes; and, conversely,

manual corrections may be

done without accompanying

product changes.

herefore, do not expect a

one-to-one correspondence

between product updates

and manual updates.

Inhaltsverzeichnis

Andere Agilent Technologies Steuereinheit Handbücher

Agilent Technologies

Agilent Technologies 6850 GC Bedienungsanleitung

Agilent Technologies

Agilent Technologies G3375A Bedienungsanleitung

Agilent Technologies

Agilent Technologies N5102A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 81570A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2259A Betriebsanleitung

Agilent Technologies

Agilent Technologies G1157A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 83486A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 83487A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 83481A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8495D Service-Handbuch

Agilent Technologies

Agilent Technologies Turbo-V Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3307A Betriebsanleitung

Agilent Technologies

Agilent Technologies 8498A Service-Handbuch

Agilent Technologies

Agilent Technologies N5532A Handbuch

Agilent Technologies

Agilent Technologies HP E1355A Bedienungsanleitung

Agilent Technologies

Agilent Technologies G4239C Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8494A Service-Handbuch

Agilent Technologies

Agilent Technologies LC Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 355C Service-Handbuch

Agilent Technologies

Agilent Technologies SD-1 Bedienungsanleitung

Agilent Technologies

Agilent Technologies E8257DS02 Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2261A Betriebsanleitung

Agilent Technologies

Agilent Technologies VXI 75000 C Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies E1339A Betriebsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung