Agilent Technologies E8361AU-016 Installations- und Betriebshandbuch

Agilent Kit Number: E8361-60102

Agilent Document Number: E8361-90003

Printed in USA June 2008

Supersedes print date: May 2008

©Agilent Technologies, Inc. 2004, 2005, 2007, 2008

Installation Note

Receiver Attenuators Upgrade Kit

To Add Option 016

Upgrade Kit Order Numbers: E8361AU-016 and E8361CU-016

For E8361A/C PNA Series Microwave Network Analyzers

2Installation Note E8361-90003

Notice

THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT TO

BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE MAXIMUM

EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL WARRANTIES,

EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY INFORMATION

CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. AGILENT SHALL NOT BE

LIABLE FOR ERRORS OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE FURNISHING, USE, OR PERFORMANCE OF THIS DOCUMENT OR

ANY INFORMATION CONTAINED HEREIN. SHOULD AGILENT AND THE USER HAVE A

SEPARATE WRITTEN AGREEMENT WITH WARRANTY TERMS COVERING THE MATERIAL IN

THIS DOCUMENT THAT CONFLICT WITH THESE TERMS, THE WARRANTY TERMS IN THE

SEPARATE AGREEMENT WILL CONTROL.

DFARS/Restricted Rights Notice

If software is for use in the performance of a U.S. Government prime contract or subcontract,

Software is delivered and licensed as “Commercial computer software” as defined in DFAR

252.227-7014 (June 1995), or as a “commercial item” as defined in FAR 2.101(a) or as

“Restricted computer software” as defined in FAR 52.227-19 (June 1987) or any equivalent

agency regulation or contract clause. Use, duplication or disclosure of Software is subject to

Agilent Technologies’ standard commercial license terms, and non-DOD Departments and

Agencies of the U.S. Government will receive no greater than Restricted Rights as defined in

FAR 52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater than

Limited Rights as defined in FAR 52.227-14 (June 1987) or DFAR 252.227-7015 (b)(2)

(November 1995), as applicable in any technical data.

Safety Notes

The following safety notes are used throughout this document. Familiarize yourself with each

of these notes and its meaning before performing any of the procedures in this document.

WARNING Warning denotes a hazard. It calls attention to a procedure which,

if not correctly performed or adhered to, could result in injury or

loss of life. Do not proceed beyond a warning note until the

indicated conditions are fully understood and met.

CAUTION Caution denotes a hazard. It calls attention to a procedure that, if not

correctly performed or adhered to, could result in damage to or destruction

of the instrument. Do not proceed beyond a caution sign until the indicated

conditions are fully understood and met.

Installation Note E8361-90003 3

Contacting Agilent

Assistance with test and measurements needs and information on finding a local Agilent

office are available on the Web at:

www.agilent.com/find/assist

If you do not have access to the Internet, please contact your Agilent field engineer.

NOTE In any correspondence or telephone conversation, refer to the Agilent product by

its model number and full serial number. With this information, the Agilent

representative can determine whether your product is still within its warranty

period.

About Installing the Upgrade Kit

IMPORTANT Option 016 can only be installed on analyzers with the option

combinations listed below as “Products affected”. If your analyzer does not

have the proper options (as listed below), it will be necessary to install

those options BEFORE installing this option (Option 016).

Description of Option 016 Receiver Attenuators

This option adds a 50-dB step attenuator in the channel A and channel B signal paths.

Products affected. . . . . . . . . . . . . . . . . . . . . . . . E8361A/C with Options 014 and UNL (with or

without Options 080 and 081)

Installation to be performed by . . . . . . . . . . . . Agilent service center or personnel qualified

by Agilent

Estimated installation time . . . . . . . . . . . . . . . 1.0 hour

Estimated adjustment time . . . . . . . . . . . . . . . 1.0 hour

Estimated full instrument calibration time . . 4.5 hours

4Installation Note E8361-90003

Items Included in the Upgrade Kit

Check the contents of your kit against this list. If any item is missing or damaged, contact

Agilent Technologies. Refer to “Contacting Agilent” on page 3.

Table 1 Contents of Option 016 Upgrade Kit (E8361-60102)

Ref.

Desig. Description Qty Part Number

Installation note (this document) 1 E8361-90003

ROHS addendum 1 9320-6722

Machine screw, M3.0 x 8 (for attaching attenuators) 4 0515-0372

A43, A44 50-dB step attenuator 2 84905-60001

Ribbon cable (for A43 and A44 step attenuators) 2 8121-0819

W20 RF cable, A8 synthesizer J106 to A17 LOMA 12 J2 1 E8361-20046

W21 RF cable, A8 synthesizer J101 to A17 LOMA 12 J3 1 E8361-20045

W47 RF cable, A43 channel A step attenuator to A27 channel A mixer 1 E8361-20064

W48 RF cable, A44 channel B step attenuator to A30 channel B mixer 1 E8361-20025

W49 RF cable, PORT 1 RCVR A IN to A43 channel A step attenuator 1 E8361-20032

W50 RF cable, PORT 2 RCVR B IN to A44 channel B step attenuator 1 E8361-20029

Installation Note E8361-90003 5

Installation Procedure for the Upgrade Kit

The network analyzer must be in proper working condition prior to installing this option. Any

necessary repairs must be made before proceeding with this installation.

WARNING This installation requires the removal of the analyzer’s protective outer

covers. The analyzer must be powered down and disconnected from the

mains supply before performing this procedure.

Electrostatic Discharge Protection

Protection against electrostatic discharge (ESD) is essential while removing or connecting

cables or assemblies within the network analyzer.

Static electricity can build up on your body and can easily damage sensitive internal circuit

elements when discharged. Static discharges too small to be felt can cause permanent

damage. To prevent damage to the instrument:

•always wear a grounded wrist strap having a 1 MΩresistor in series with it when handling

components and assemblies.

•always use a grounded, conductive table mat while working on the instrument.

•always wear a heel strap when working in an area with a conductive floor. If you are

uncertain about the conductivity of your floor, wear a heel strap.

Figure 1 shows a typical ESD protection setup using a grounded mat and wrist strap. Refer to

“Tools and Equipment Required for the Installation” on page 7 for part numbers.

Figure 1 ESD Protection Setup

6Installation Note E8361-90003

Overview of the Installation Procedure

Step 1. Remove the Outer Cover.

Step 2. Replace (if necessary) Cables W20 and W21.

Step 3. Remove the Front Panel Assembly.

Step 4. Raise the Receiver Deck.

Step 5. Remove the Existing Cables.

Step 6. Install the Attenuators and New Cables.

Step 7. Lower and Fasten the Receiver Deck.

Step 8. Reinstall the Front Panel Assembly and Front Panel Jumpers.

Step 9. Reinstall the Outer Cover.

Step 10. Enable Option 016.

Step 11. Perform Post-Upgrade Adjustments and Calibration.

Installation Note E8361-90003 7

Tools and Equipment Required for the Installation

CAUTION Use a 5/16-inch torque wrench set to 10 in-lbs on all cable connections except the

front-panel connectors to which the front-panel jumpers attach (Option 014).

Use a 5/16-inch torque wrench set to 21 in-lbs for these connections.

Test Equipment Required for Post-Upgrade Adjustments

Description Qty Part Number

T-10 TORX driver (set to 9 in-lbs) 1 N/A

T-20 TORX driver (set to 21 in-lbs) 1 N/A

5/16-inch torque wrench (set to 10 in-lbs) 1 N/A

5/16-inch torque wrench (set to 21 in-lbs) (Option 014 only) 1 N/A

ESD grounding wrist strap 1 9300-1367

5-ft grounding cord for wrist strap 1 9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire 1 9300-0797

ESD heel strap (for use with conductive floors) 1 9300-1308

Description Agilent Part Number

Power meter E4418B/E4419B

Power sensor, Type-N (100 kHz–4.2 GHz) 8482A

Power sensor, 2.4 mm (4.2 GHz–50 GHz) 8487A

Power sensor, V-Band (50 GHz–67 GHz)a

a. This sensor and adapter must be calibrated together by the Agilent factory. The data supplied

are only valid as long as the sensor and adapter remain connected.

V8486A

Adapter, WR-15 to 1.85 mm (m)aV281B

Adapter, 1.85 mm (f) to 1.85 mm (f)b

b. The 1.85 mm connector has the same ruggedness and is compatible with the 2.4 mm connec-

tor. 1.85 mm and 2.4 mm connectors and adapters may be used interchangeably.

85058-60114

Adapter, 2.4 mm (f) to 2.4 mm (f)b11900B

Adapter, Type-N (f) to 2.4 mm (f) 11903B

Test cable, 2.4 mm (f) to 2.4 mm (f)bor

Test cable, 1.85 mm (f) to 1.85 mm (f)b

85133C

N4697E

8Installation Note E8361-90003

Step 1. Remove the Outer Cover

CAUTION This procedure is best performed with the analyzer resting on its front handles

in the vertical position. Do not place the analyzer on its front panel without the

handles. This will damage the front panel assemblies.

Refer to Figure 2.

1. Disconnect the power cord (if it has not already been disconnected).

2. With a T-20 TORX driver, remove the four rear panel feet (item {) by removing the center

screws (item |).

3. Slide the four bottom feet (item }) off the cover.

4. With a T-20 TORX driver, remove the strap handles (item ~) by loosening the screws

(item ) on both ends until the handle is free of the analyzer.

5. Slide the cover off of the frame.

Figure 2 Outer Cover Removal

NOTE The figure above shows the E8361A front panel and floppy disk drive. The

E8361C front panel has a slightly different appearance and does not

include a floppy disk drive.

Installation Note E8361-90003 9

Step 2. Replace (if necessary) Cables W20 and W21

Refer to Figure 3 and Figure 4.

1. Place the analyzer top-side up.

2. With a T-10 TORX driver, remove the 11 screws (item {) used to attach the inner cover

and lift off the inner cover.

3. Examine the part number labels on cables W20 (connected to A8J106) and W21 (connected

to A8J101).

• If the part numbers are E8361-20045 and E8361-20046 respectively, then they do not

need to be replaced. Proceed to step 5 on the next page.

• If the part numbers ARE NOT E8361-20045 and E8361-20046 respectively, they need to

be replaced. Continue at step 4 on the next page.

Figure 3 Inner Cover Removal to Verify W20 and W21 Part Numbers

NOTE The figure above shows the E8361A front panel and floppy disk drive. The

E8361C front panel has a slightly different appearance and does not

include a floppy disk drive.

4. To replace cables W20 and W21:

10 Installation Note E8361-90003

a. Place the analyzer on its side as shown in Figure 4.

b. Remove the cable hold-down wire (item |).

c. Disconnect cables W20 and W21 at both ends; two top side connections and two bottom

side connections. Remove the cables from the analyzer.

d. Position the new cables in the analyzer and connect them as follows: W20–A8J106 to

A17J2; W21–A8J101 to A17J3. Tighten the connectors to 10 in-lbs.

e. Reinstall the cable hold-down wire (item |).

Figure 4 Replacing Cables W20 and W21

5. Replace the inner cover by reinstalling the 11 attachment screws (item {).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Agilent Technologies Steuereinheit Handbücher

Agilent Technologies

Agilent Technologies 355C Service-Handbuch

Agilent Technologies

Agilent Technologies 4890 Bedienungsanleitung

Agilent Technologies

Agilent Technologies G4239C Bedienungsanleitung

Agilent Technologies

Agilent Technologies Turbo-V Bedienungsanleitung

Agilent Technologies

Agilent Technologies G1360A Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies 83481A Bedienungsanleitung

Agilent Technologies

Agilent Technologies N5102A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8495D Service-Handbuch

Agilent Technologies

Agilent Technologies E1476A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8498A Service-Handbuch

Agilent Technologies

Agilent Technologies LC Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2259A Betriebsanleitung

Agilent Technologies

Agilent Technologies E2261A Betriebsanleitung

Agilent Technologies

Agilent Technologies N2757A Bedienungsanleitung

Agilent Technologies

Agilent Technologies G2623A Bedienungsanleitung

Agilent Technologies

Agilent Technologies VXI 75000 C Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies X3507-64002 Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfinityLab G4237A Bedienungsanleitung

Agilent Technologies

Agilent Technologies N5532A Handbuch

Agilent Technologies

Agilent Technologies 34946A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8490D Service-Handbuch

Agilent Technologies

Agilent Technologies 81662A Bedienungsanleitung

Agilent Technologies

Agilent Technologies G1157A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 54751A Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung