Agilent Technologies U3402A Bedienungsanleitung

Agilent Technologies

Agilent U3402A

5 1/2 Digit Dual Display

Multimeter

Quick Start Guide

ii U3402A Quick Start Guide

Notices

No part of this manual may be reproduced in

any form or by any means (including elec-

tronic storage and retrieval or translation

into a foreign language) without prior agree-

ment and written consent from Agilent

Technologies, Inc. as governed by United

States and international copyright laws.

Manual Part Number

U3402-90019

Edition

First Edition, March 18, 2009

Agilent Technologies, Inc.

5301 Stevens Creek Blvd.

Santa Clara, CA 95052 USA

Warranty

The material contained in this docu-

ment is provided “as is,” and is sub-

ject to being changed, without notice,

in future editions. Further, to the max-

imum extent permitted by applicable

law, Agilent disclaims all warranties,

either express or implied, with regard

to this manual and any information

contained herein, including but not

limited to the implied warranties of

merchantability and fitness for a par-

ticular purpose. Agilent shall not be

liable for errors or for incidental or

consequential damages in connec-

tion with the furnishing, use, or per-

formance of this document or of any

information contained herein. Should

Agilent and the user have a separate

written agreement with warranty

terms covering the material in this

document that conflict with these

terms, the warranty terms in the sep-

arate agreement shall control.

Technology Licenses

The hardware and or software described in

this document are furnished under a license

and may be used or copied only in accor-

dance with the terms of such license.

Restricted Rights Legend

U.S. Government Restricted Rights. Soft-

ware and technical data rights granted to

the federal government include only those

rights customarily provided to end user cus-

tomers. Agilent provides this customary

commercial license in Software and techni-

cal data pursuant to FAR 12.211 (Technical

Data) and 12.212 (Computer Software) and,

for the Department of Defense, DFARS

252.227-7015 (Technical Data - Commercial

Items) and DFARS 227.7202-3 (Rights in

Commercial Computer Software or Com-

puter Software Documentation).

Safety Notices

CAUTION

A CAUTION notice denotes a haz-

ard. It calls attention to an operat-

ing procedure, practice, or the like

that, if not correctly performed or

adhered to, could result in damage

to the product or loss of important

data. Do not proceed beyond a

CAUTION notice until the indicated

conditions are fully understood and

met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly per-

formed or adhered to, could result

in personal injury or death. Do not

proceed beyond a WARNING

notice until the indicated condi-

tions are fully understood and

met.

U3402A Quick Start Guide iii

Contents

The Front Panel at a Glance 1

The Display at a Glance 2

Getting Started 4

1 Connect the power cord 4

2 Adjust the carrying handle 4

3 Connect the test leads to the input terminals 5

4 Turn on the multimeter 5

5 Select a function 6

6 Set the range 6

7 Set the reading rate 6

8 Using the secondary display 7

9 Math operation 7

10 For more information 8

iv U3402A Quick Start Guide

U3402A Quick Start Guide 1

The Front Panel at a Glance

Primary display Secondary display

Input terminals

and current fuse

Power

on/off

switch

Shift

Math

operation

keypads

Autoranging,

manual range

and comparator

operation

Measurement

function

keypads

2U3402A Quick Start Guide

The Display at a Glance

Figure 1-1 VFD full display with all segments illuminated

The highly visible vacuum fluorescent display (VFD) annunciators are

described in the following table:

Annunciator Description

Primary display

SReadingrate:Slow

M Reading rate: Medium

FReadingrate:Fast

PEAK Peak measurement. Not applicable for the U3402A.

HOLD Data hold

MIN MinMax math operation: Minimum value shown on the primary display

MAX MinMax math operation: Maximum value shown on the primary display

REL Relative value

dBm Decibel unit relative to 1 mW

4 2 W 4-wire/2-wire resistance

Diode test

Audible continuity test for resistance

AUTO Autoranging

DC Direct current

AC Alternating current

DCAC AC + DC

Polarity, digits, and decimal points for primary display

ºC Celcius temperature unit. Not applicable for the U3402A.

ºF Fahrenheit temperature unit. Not applicable for the U3402A.

U3402A Quick Start Guide 3

Annnciator Description

mV Voltage unit: mV, V

µmA Current unit: µA, mA, A

µmnF Capacitance unit: nF, µF, mF. Not applicable for the U3402A.

Resistance unit:

, k

, M

MkHz Frequency unit: Hz, kHz, MHz

Secondary display

Polarity, digits, and decimal points for secondary display

µnmF Capacitance unit: nF, µF, mF. Not applicable for the U3402A.

ºC Celcius temperature unit. Not applicable for the U3402A.

ºF Fahrenheit temperature unit. Not applicable for the U3402A.

% Duty cycle measurement. Not applicable for the U3402A.

mV Voltage unit: mV, V

µmA Current unit: µA, mA, A

SShiftmode

Resistance unit:

, k

, M

MkHz Frequency unit: Hz, kHz, MHz

2ND Secondary display is enabled

AUTO Autoranging

DC Direct current

AC Alternating current

DCAC AC + DC

COMP Compare operation

dBm Decibel unit relative to 1 mW

CAL Calibration mode. Not applicable for the U3402A.

EXT External. Not applicable for the U3402A.

TRIG Trigger mode. Not applicable for the U3402A.

REMOTE Remote interface control. For calibration use only.

LOCAL Local mode

STO Store instrument state. Not applicable for the U3402A.

RCL Recall stored instrument state. Not applicable for the U3402A.

4U3402A Quick Start Guide

Getting Started

This section describes the basic step- by- step procedures on how to operate

the multimeter.

1 Connect the power cord

2 Adjust the carrying handle

Grasp the handle by the sides and pull outward as indicated by the red

arrows below.

Then, adjust the handle to the desired position.

NOTE

The line voltage switch and fuse are set at the factory according to the country of

destination.

U3402A Quick Start Guide 5

3 Connect the test leads to the input terminals

4 Turn on the multimeter

Push to turn on the multimeter. The front- panel display illuminates

while the multimeter performs its power- on self- test.

The multimeter powers up in the DC voltage function with autoranging

enabled. Typical display:

–

AC or DC voltage, frequency, or resistance measurement

and diode or continuity test.

–

AC or DC current

up to 1.2 A RMS

AC or DC current

up to 12 A RMS

–

6U3402A Quick Start Guide

5 Select a function

Press one of the following keys to select a measurement function.

6 Set the range

For most measurement functions, you can allow the multimeter to select

the range automatically by using the autoranging function, or you can

select a fixed range using manual ranging. The AUTO annunciator is

displayed when the autoranging function is selected.

7 Set the reading rate

You can select three reading rates: S(slow), M(medium) and F(fast) for

the AC and DC voltage, AC and DC current, and resistance measurement.

Press to cycle through the available reading rates (S, M, or F).

A slower reading rate provides for better accuracy and noise rejection

readings. A faster reading rate will result in faster but lower accuracy

readings.

Selects autoranging and disables manual ranging. Press to

toggle between the manual ranging and autoranging.

Selects a higher range and disables autoranging.

Selects a lower range and disables autoranging.

NOTE

In the dBm function, the display counts is 0.01 dBm for the slow or medium reading rate

and 0.1 dBm for the fast reading rate.

Andere Handbücher für U3402A

Inhaltsverzeichnis

Sprachen:

Andere Agilent Technologies Multimeter Handbücher

Agilent Technologies

Agilent Technologies 3458A Kurzanleitung

Agilent Technologies

Agilent Technologies U1273A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1253A Handbuch

Agilent Technologies

Agilent Technologies U1270 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1253B Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1251B Handbuch

Agilent Technologies

Agilent Technologies U1231A Bedienungsanleitung

Agilent Technologies

Agilent Technologies L34410A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34401A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U3402A Handbuch

Agilent Technologies

Agilent Technologies U2741A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1242A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1273A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1251A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8153A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1253B Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1241B Handbuch

Agilent Technologies

Agilent Technologies U3606B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34450A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U3606B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34450A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 3457A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U3606A Handbuch

Agilent Technologies

Agilent Technologies 34450A Montage- und Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung

Morris

Morris 57074 Bedienungsanleitung