Agilent Technologies 6680A Kurzanleitung

6684A-03

SERVICE NOTE

6684A GPIB Power Supply

Serial Number: See below

A9 Down Programmer Failures

Duplicate Service Notes:

6680A-04 0000A00000 / US36480157 except US36480140

6681A-04 0000A00000 / US36400444 except US36400434 and US36400441

6682A-03 0000A00000 / US36440295

6683A-03 0000A00000 / US36420359

6684A-03 0000A00000 / US36410425 except US36420317 and US36410320

To Be Performed By: Agilent-Qualified Personnel

Parts Required:

Parts to repair A9 Assembly if A9 is repairable:

For models 6680A and 6681A:

Qty 1 p/n 5064-0142

(kit containing 2 FET’s 5182-9080, 2 insulators 0340-1507 and 6 sockets 1251-4211)

For models 6682A, 6683A and 6684A:

Qty 1 p/n 5064-0141

(kit containing 2 FET’s 5182-9079, 2 insulators 0340-1507 and 6 sockets 1251-4211)

Continued

ADMINISTRATIVE INFORMATION

SERVICE NOTE CLASSIFICATION:

MODIFICATION RECOMMENDED

ACTION

CATEGORY: IMMEDIATELY

ON SPECIFIED FAILURE

AGREEABLE TIME

STANDARDS:

LABOR 3.0 Hours

LOCATION

CATEGORY: CUSTOMER INSTALLABLE

ON-SITE

SERVICE CENTER

SERVICE RETURN

INVENTORY: SCRAP

SEE TEXT

USED RETURN

PARTS: SCRAP

SEE TEXT

AVAILABILITY: PRODUCT’S SUPPORT LIFE AGILENT RESPONSIBLE UNTIL: December 2001

AUTHOR: PS ENTITY: 2100 ADDITIONAL INFORMATION:

PRINTED IN U.S.A.

SUPERSEDES: NONE

DATE: December 1999

1 of 3

Parts required if A9 Assembly is to be replaced:

For Model Number:

6680A: Qty 1 06680-60022 Down Programmer/Slow sense Assy

Qty 1 5064-0142 FET Kit

6681A: Qty 1 06681-60022 Down Programmer/Slow sense Assy

Qty 1 5064-0142 FET Kit

6682A: Qty 1 06682-60022 Down Programmer/Slow sense Assy

Qty 1 5064-0141 FET Kit

6683A: Qty 1 06683-60022 Down Programmer/Slow sense Assy

Qty 1 5064-0141 FET Kit

6684A: Qty 1 06684-60022 Down Programmer/Slow sense Assy

Qty 1 5064-0141 FET Kit

Situation:

The output voltage cannot be lowered rapidly when the output is disabled or programmed to a

lower voltage. Cause: the sockets for field effect transistors (FET’s), A9 Q981 and A9 Q982,

have been found to overheat disabling the down programmer ciruit. Often the A9 can be easily

and quickly repaired.

Solution / Action:

1) Using the disassembly procdures in the service manual, remove the top cover, the protective

RFI Shield (galvanized sheet metal) and the A10 control assembly.

2) Without removing the A9, visually inspect the area around the FET sockets on the A9 as-

sembly. Look for signs of overheating. If the board is badly damgaged as indicated by lifted

traces and/or burned circuit board material, the A9 assembly will need to be replaced. If the

A9 board material is only discolored continue with step 3. If the A9 has to be replaced, also

replace the FET’s. Use the normal procedure for replacing the A9 and FET’s and, in addi-

tion, follow step 6 below to solder the FET leads into the sockets.

3) Remove the screws holding the A9 FET’s down to the heatsink and unplug the FET’s from

the A9 assembly. Discard the old insulators and FET’s.

4) Remove overheated FET sockets from the A9 assembly: Using a soldering iron and long

nose pliers, heat up the sockets from the side facing the outside of the unit and carefully

push them part way in. Next grasp them from the inside and remove them. Be careful not to

drop solder or sockets into the unit. Clean the plated-thru holes with desoldering braid.

5) Insert the new sockets into the A9 (don’t solder them in yet). Insert the new FET’s into the

sockets and mount them to the heatsink using new insulators. Make sure that the sockets are

fully seated into the circuit board. Do not use heatsink compound or overtighten the screws.

6) Carefully flow solder around the sockets on the side facing away from the heatsink (out-

side) and then carefully flow solder around the FET leads and INTO the sockets on the side

facing the heatsink. By applying heat only to the sockets, the solder will draw into the sock-

ets and will not flow toward the body of the FET’s.

7) Re-install the A10 control assembly, shields, and cover by reversing the disassembly proce-

dure in the manual.

Continued

Page 2 Service Note 6684A-03

8) Test the down programming circuits: With no load attached to the power supply, monitor

the output voltage with an external voltmeter. Program the output voltage for the model’s

highest rated voltage. Switch the output off. If the down programmer circuit is operational,

the output voltage will drop to zero in a fraction of a second. If the down programmer cir-

cuit is not operational, the filter capacitors will take tens of seconds to discharge.

Service Note 6684A-03 Page 3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Agilent Technologies Stromversorgung Handbücher

Agilent Technologies

Agilent Technologies U8001A Handbuch

Agilent Technologies

Agilent Technologies 6112A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 654xA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 87421A Bedienungs- und Sicherheitshinweise

Agilent Technologies

Agilent Technologies 6443B Service-Handbuch

Agilent Technologies

Agilent Technologies E3647A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6201B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 654 A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6023A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6641A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6010A Bedienungsanleitung

Agilent Technologies

Agilent Technologies HP8648A Service-Handbuch

Agilent Technologies

Agilent Technologies 66332A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E3632A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 729-0800 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6010A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E3633A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 66311A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E3620A Service-Handbuch

Agilent Technologies

Agilent Technologies E3632A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E361 A Series Service-Handbuch

Agilent Technologies

Agilent Technologies E3631-90002 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 66000A Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung

Elmdene

Elmdene G1380xN-y-s Series Bedienungsanleitung

DTS

DTS Megashock 5 Bedienungsanleitung