Agilent Technologies InfiniiVision MSO6104A Kurzanleitung

–

ADMINISTRATIVE INFORMATION

SERVICE NOTE CLASSIFICATION:

PRIORITY SAFETY

ACTION STANDARDS:

CATEGORY: X IMMEDIATELY LABOR: 0.5 Hours

LOCATION SERVICE [[]] RETURN USED [[]] RETURN

CATEGORY: ON-SITE INVENTORY: [[]] SCRAP PARTS: [[]] SCRAP

X SERVICE CENTER X SEE TEXT X SEE TEXT

AVAILABILITY: ALWAYS AGILENT RESPONSIBLE UNTIL: ALWAYS

AUTHOR: DPM PRODUCT LINE: 1A

ADDITIONAL INFORMATION:

PRINTED IN U.S.A.

March 19, 2007

Page 1 of 9

MSO6104A-01A-S

S E R V I C E N O T E

Supersedes:

MSO6104A-01-S

MSO6104A 4+16-channel, 1 GHz Mixed Signal Oscilloscope

Serial Numbers: MY44001001

POSSIBLE SHOCK HAZARD

The loss of earth ground and mechanical tolerance variations in PCA and

instrument assembly may cause the power supply shield to short a trace to

ground creating a shock hazard.

To Be Performed By: Agilent-Qualified Personnel

Parts Required:

P/N Description Qty.

54684-85402 Dielectric insulator 1

Page 2 of 9 MSO6104A-01A-S

Situation:

The loss of earth ground and mechanical tolerance variations in PCA and instrument assembly may

cause the power supply shield to short a trace to ground creating a shock hazard.

Solution/Action:

The solution is to install dielectric insulator to the inside wall of the power supply shield. This

modification to customer units will be performed by Agilent Technologies authorized service

personnel at the customer site.

To perform the modification:

Read All Warnings and Cautions

Read the following warnings and cautions before performing this procedure.

WARNING -- HAZARDOUS VOLTAGES!

Only trained service personnel who are aware of the hazards involved should perform the maintenance.

Whenever possible, perform the procedures with the power cord removed from the oscilloscope.

WARNING -- AVOID ELECTRICAL SHOCK!

Hazardous voltages exist on the LCD assembly and power supply. To avoid electrical shock:

1. Disconnect the power cord from the oscilloscope.

2. Wait at least three minutes for the capacitors in the oscilloscope to discharge before you begin disassembly.

CAUTION -- REMOVE POWER TO AVOID DAMAGE!

Remove power before you begin to remove and replace assemblies. Do not remove or replace assemblies

while the oscilloscope is turned on, or damage to the components can occur.

CAUTION -- AVOID DAMAGE TO ELECTRONIC COMPONENTS!

ELECTROSTATIC DISCHARGE (ESD) can damage electronic components. When doing any of the

procedures in this chapter, use proper ESD precautions. As a minimum, you should place the instrument

on a properly grounded ESD mat and wear a properly grounded ESD strap.

Page 3 of 9 MSO6104A-01A-S

To remove the cabinet

1. Turn off the oscilloscope and disconnect the power cable.

2. Rotate the handle to the up position as shown.

3. Using the T20 TORX driver, remove the two screws from the rear of the cabinet.

4. Using your thumbs, gently push on the rear-panel connectors to slide the oscilloscope out of the

cabinet.

Figure 1 Remove the cabinet.

T-20 Screw

Gently Push on the

connectors

Page 4 of 9 MSO6104A-01A-S

To remove the power supply shield

1. Pull back on each side of the shield until the 4 side hook legs clear their slots in the deck.

WARNING -- Thin sheet metal parts may have sharp edges. Handle with care to avoid injury.

Figure 2 Release hook legs from deck.

Pull back

Hook Legs

Hook Leg

Slot in Deck

Page 5 of 9 MSO6104A-01A-S

2. Lift to remove the shield.

To install the dielectric insulator tape

1. Turn the shield on it’s side as shown.

2. Clean the adhesion area on the shield with alcohol.

Figure 3 Prepare to install insulator.

3. Apply the dielectric insulator to the shield ensuring that it is within the tolerances shown.

Adhesion Area

Page 6 of 9 MSO6104A-01A-S

Figure 4 Apply dielectric insulator.

Page 7 of 9 MSO6104A-01A-S

To reinstall the power supply shield

1. Ensure that tabs and hook legs have not been damaged.

Figure 5 Proper angles for tabs and hook legs.

Angled tabs

Angled hook legs

Damaged hook tab Proper hook tab

Page 8 of 9 MSO6104A-01A-S

2. Insert the 4 tabs at the front of the shield by tilting the shield up.

Figure 6 Tilt to insert tabs.

3. Tilt the shield down and pull back slightly to insert the 4 side hook legs into their deck slots.

4. Push the shield forward to lock into place.

Insert tabs in deck

slots

Tilt up

Page 9 of 9 MSO6104A-01A-S

Ensure all hooks and tabs are inserted correctly in their slots.

Figure 7 Insert hook legs and lock.

To reinstall the cabinet

1. Slide the oscilloscope into the cabinet until connectors are fully in their openings in the rear

panel.

2. Replace the two T20 screws shown in Figure 1 on page 3.

Run user self test

Follow the instructions in the service guide to verify that the instrument passes User Self Test. No

calibration is required.

Insert Lock

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Agilent Technologies Prüfgeräte Handbücher

Agilent Technologies

Agilent Technologies 54621A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U7242A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E5022A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8960 Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies U1452A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8960 Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 4000 X-Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 54835A Bedienungsanleitung

Agilent Technologies

Agilent Technologies DisplayPort Installations- und Betriebsanleitung

Agilent Technologies

Agilent Technologies 93000 SOC Series Installationsanleitung

Agilent Technologies

Agilent Technologies E6621A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1610/20A Bedienungsanleitung

Agilent Technologies

Agilent Technologies XX3625 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 11645A Series Handbuch

Agilent Technologies

Agilent Technologies E8285A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 90000 X Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies ProBER 2 Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1602B Handbuch

Agilent Technologies

Agilent Technologies 4072A Advanced Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 5000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies U2701A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 54621A Bedienungsanleitung

Agilent Technologies

Agilent Technologies N5980A Betriebsanleitung

Agilent Technologies

Agilent Technologies 81250 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Ritmix

Ritmix RAT-701 Bedienungsanleitung