Agri-Fab 45-02143 Bedienungsanleitung

CAUTION:

Read Rules for

Safe Operation

and Instructions

Carefully

100 LB. PUSH

BROADCAST SPREADER

PRINTED IN U.S.A. FORM NO. 40470 (REV. 05/08/08)

OWNERS

MANUAL

Model No.

45-02143

Assembly

Operation

Maintenance

Repair Parts

the fastest way to purchase parts

www.speedepart.com

™

RULES FOR SAFE OPERATION

The following safety precautions are suggested. This

broadcast spreader is designed, engineered and tested to

offer reasonably safe and effective service, provided it is

operated in strict accordance with these instructions.Failure

to do so may result in personal injury. Always observe the

rules of safe operation.

1. Do not allow anyone to operate the broadcast spreader

without proper instructions.

2. Do not permit children to operate the broadcast

spreader.

3. Wear eye and hand protection when handling and

when applying lawn or garden chemicals.

4. Read the chemical label instructions and cautions for

handling and applying the chemicals purchased for

spreading.

5. Keep all nuts, bolts and screws tight to be sure

equipment is in safe working condition.

6. Follow maintenance and lubrication instructions as

outlined in this manual.

CARTON CONTENTS

LOOSE PARTS IN CARTON

1. Handle Tube (long)

2. Braces (2)

3. Flow Control Mount Bracket

4. Flow Control Arm

5. Handle Tube (short)

6. Flow Control Rod

7. Leg Stand Tube

8. Drive Wheel

9. Wheel

10. Hopper Assembly

Hardware Package (not shown)

710

3 4

LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT

MEANS — ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED.

NOT SHOWN FULL SIZE

AB C D E

KJ LMN

SHOWN FULL SIZE

KEY QTY DESCRIPTION

A 2 Hex Bolt, 1/4-20 x 1-3/4" Long

B 5 Hex Bolt, 1/4-20 x 1-1/2" Long

C 2 Hex Bolt, 1/4-20 x 1" Long

D 1 Carriage Bolt, 1/4-20 x 3/4" Long

E 9 Nyock Nut, 1/4"

F 6 Flat Washer, 5/16" SAE

G 4 Nylon Washer

H 3 Flat Washer, 1/2"

I 1 Cotter Pin, 3/32" x 3/4" Long

KEY QTY DESCRIPTION

J 1 Flow Control Link

K 2 Spacer Tube

L 2 Hub Cap

M 1 Grip

N 1 Vinyl Cap

O 1 Nylon Wing Nut

P 2 Handle Grip

Q 1 Adjustable Stop

ASSEMBLY INSTRUCTIONS

TOOLS REQUIRED FOR ASSEMBLY

(1) Pliers

(1) Hammer

(2) 7/16" Open or Boxed End Wrenches

1. Remove the spreader, the loose parts and the hardware

package from the carton. Lay out parts and hardware

and identify using the illustrations on pages 2 and 3.

2. With the spreader resting upside down on the top of

the hopper, assemble a spacer and then a 1/2" at

washer onto each end of the axle. See gure 1.

FIGURE 2

FIGURE 1

FIGURE 3

5. Place the drive wheel onto the end of the axle that has

an indent. The long end of the hub goes to the inside.

See gure 3.

6. Lightly tap a hub cap onto the axle until it is snug against

the wheel. See gure 3.

FIGURE 4

3. Place a wheel onto the end of the axle that has no

cross hole.The long end of the hub goes to the inside.

See gure 2.

4. Place a 1/2" at washer onto the axle and then lightly

tap a hub cap onto the axle until it is snug against the

washer and wheel hub. See gure 2.

AXLE

SPACER

1/2" FLAT

WASHER

1/2" FLAT

WASHER

HUB CAP

WHEEL

NO CROSS HOLE

HUB CAP

WHEEL

7. Remove the middle 1/4" hex bolt, at washer and hex

lock nut from the crossover tube. See gure 4.

CROSSOVER

TUBE

MIDDLE NUT

SHAFT

SUPPORT

PLATE

MIDDLE BOLT

& WASHER

FIGURE 7

12. Assemble the leg stand tube to the handle tube (long)

using two 1/4" x 1-1/2" hex bolts. Secure tightly with

two 1/4" nylock nuts. See gure 6.

13. Place a vinyl cap over the end of the leg stand tube.

See gure 6.

FIGURE 5

FIGURE 6

14. Assemble the ow control link (end with small hole)

to the ow control arm using a 1/4" x 1" hex bolt, a

nylon washer and a 1/4" nylock nut as shown in gure

7. Tighten carefully. The ow control link should not

be loose but should pivot with no more than slight

resistance.

HANDLE TUBE (LONG)

1/4" x 1-1/2"

HEX BOLTS

1/4"

NYLOCK

NUT

VINYL CAP LEG STAND TUBE

FLOW CONTROL

LINK FLOW

CONTROL

ARM

1/4" NYLOCK NUT

1/4" x 1"

HEX BOLT

SMALLEST

HOLE

NYLON

WASHER

IMPORTANT: Do Not asssemble handle tube to same

side of crossover tube as shaft support plate.

8. Place the long handle tube onto the crossover tube

on the side opposite from the shaft support plate.

Fasten with the bolt, at washer and nut removed in the

previous step. See gures 4 and 5. Do not tighten at

this time.

9. Assemble two handle braces to the inside of the hopper

frame, one on each side, using two 1/4" x 1-1/2" hex

bolts and two 1/4" nylock nuts. See gure 5. Do not

tighten at this time.

10. Assemble the other end of the two handle braces to the

long handle tube using a 1/4" x 1-1/2" hex bolt and 1/4"

nylock nut. Do not tighten at this time. See gure 5.

11. Tighten all hex lock nuts and bolts in same sequence

as assembled in steps 9 through 11. See gure 5.

MIDDLE

BOLT &

WASHER

MIDDLE

NUT

HANDLE TUBE (LONG)

HEX BOLT

1/4" x 1-1/2"

HEX BOLT

1/4" x 1-1/2"

HITCH

BRACE

1/4"

NYLOCK

NUT

CROSSOVER

TUBE

SHAFT

SUPPORT

PLATE

FIGURE 8

FIGURE 9

18. Hook the free end of the ow control rod through the

hole in the slide gate bracket located near the bottom

of the hopper. See gure 10.

FIGURE 10

FIGURE 11

15. Assemble the ow control arm to the ow control

mounting bracket using a 1/4" x 1" hex bolt, two nylon

washers and a 1/4" nylock nut as shown in gure 8.

Tighten carefully. The ow control arm should be

snug, but should pivot with no more than a slight

resistance.

16. Assemble the vinyl grip. See gure 8.

17. Place a 5/16" at washer onto the end of the ow control

rod. Insert the end of the ow control rod through the

slot in the ow control mounting bracket and through

the hole in the ow control link. Secure with a 3/32" x

3/4" cotter pin. See gure 9.

19. Assemble both the ow control mounting bracket and

the short handle tube to the long handle tube. Use two

1/4" x 1-3/4" hex bolts, four 5/16" at washers and two

1/4" nylock nuts as shown in gure 11. Do not tighten

at this time.

20. Place a handle grip on each handle. See gure 11.

1/4" x 1-3/4"

HEX BOLT

1/4" NYLOCK

NUT

HANDLE

TUBE

(SHORT)

HANDLE

TUBE

(LONG)

HANDLE GRIP FLOW CONTROL

MOUNTING BRACKET

5/16"

FLAT

WASHERS

HOPPER

SLIDE

GATE

BRACKET

FLOW

CONTROL

ROD

1/4" x 1"

HEX BOLT

1/4" NYLOCK

NUT

FLOW CONTROL

MOUNTING

BRACKET

FLOW

CONTROL

ARM

(2) NYLON

WASHERS

VINYL GRIP

FLOW

CONTROL

ROD

FLOW

CONTROL

LINK

3/32"

COTTER

5/16" FLAT

WASHER

SLOT

FIGURE 12

21. Place the adjustable stop into the "ON" end of the slot

in the top of the ow control mounting bracket. Secure

with the 1/4" x 3/4" carriage bolt, a nylon washer, a 5/16"

at washer and the nylon wing nut. See gure 12.

22. Position the ow control mounting bracket (gure 13).

a. Push on ow control arm until it locks in "OFF"

position.

b. Slide ow control mounting bracket along tube until

closure plate in bottom of hopper just closes.

c. Snug the 1/4" lock nuts just enough to hold ow

control mounting bracket in place.

d. Set adjustable stop at "5". Pull ow control arm

against stop. Verify that closure plate has opened

about half way.

e. If closure plate does not open half way, it may be

closed too far at "OFF". Adjust position of ow control

mounting bracket until closure plate will open about

half way at "5" and still close when arm is locked in

"OFF". Tighten 1/4" lock nuts.

5/16" FLAT

WASHER

NYLON

WASHER

1/4" x 3/4"

CARRIAGE BOLT

NYLON

WING NUT

ADJUSTABLE

STOP

23. Before operating the spreader, pre-lubricate per the

lubrication instructions in the owner's manual.

OFF

FLOW

CONTROL

ARM

OFF

AJDUSTABLE

STOP

SETTING "5"

FIGURE 13

HOW TO USE YOUR SPREADER

SETTING THE FLOW CONTROL

(Refer to gure 13 on page 7.)

1. Loosen the nylon wing nut, set the adjustable stop to

the desired ow rate setting and retighten the wing nut.

The higher the setting number, the wider the opening

in the bottom of the hopper.

2. Refer to the application chart on page 8 and to the

instructions on the fertilizer bag to select the proper

ow rate setting.

3. Pull the ow control arm against the adjustable stop

for the on position and toward the hopper for the off

position.

OPERATION

USING YOUR SPREADER

We do not recommend the use of any powdered lawn

chemicals, due to difculty in obtaining a satisfactory or

consistent broadcast pattern.

1. Determine approximate square footage of area to be

covered and estimate amount of material required.

2. Before lling the hopper make sure the ow control arm

is in the off position and the closure plate is shut.

3. Break up any lumpy fertilizer as you ll the hopper.

4. Set the adjustable stop with the ow control arm still

in the off position. Refer to the application chart on

this page and to the instructions on the fertilizer bag

to select the proper ow rate setting.

5. The application chart is calculated for light to heavy

application at a walking speed of 3 mph, or 100 ft.in 23

seconds.A variation in speed will require an adjustment

of the ow rate to maintain the same coverage. The

faster you walk, the wider the broadcast width.

6. Always start the spreader in motion before opening

the closure plate.

7. Always shut the closure plate before turning or stopping

the spreader.

8. If fertilizer is accidentally deposited too heavily in a

small area, soak the area thoroughly with a garden

hose or sprinkler to prevent burning of the lawn.

9. To insure uniform coverage, make each pass so that the

broadcast pattern slightly overlaps the pattern from the

previous pass as shown in gure 14. The approximate

broadcast widths for different materials are shown in

the application chart on this page.

10. When broadcasting weed control fertilizers, make sure

the broadcast pattern does not hit evergreen trees,

owers or shrubs.

FIGURE 14

APPLICATION DIAGRAM

OVERLAP

8' to

10'

FERTILIZER

Powder 3 - 5 3' - 4'

Granular 3 - 5 8' - 10'

Pelleted 3 - 5 10' - 12'

Organic 6 - 8 6' - 8'

GRASS SEED

Fine 3 - 4 6' - 7'

Coarse 4 - 5 8' - 9'

ICE MELTER 6 - 8 10' - 12'

TYPE SPREAD

MATERIAL FLOW SETTING WIDTH

APPLICATION CHART

OPERATING SPEED - 3 MPH. (100 ft. in 23 seconds)

IMPORTANT: Application rates shown in the chart

are affected by humidity and by the moisture content of

the material (granular and pellet). Some minor setting

adjustments may be necessary to compensate for this

condition.

FIGURE 15

CHECK FOR LOOSE FASTENERS

1. Before each use make a thorough visual check of

the spreader for any bolts and nuts which may have

loosened. Retighten any loose bolts and nuts.

CHECK FOR WORN OF DAMAGED PARTS

2. Check for worn or damaged parts before each use.

Repair or replace parts if necessary.

CHECK TIRE INFLATION

3. Check if tires are adequately inated before each use.

Do not inate tires beyond maximum recommended

pressure.

1. Rinse inside of hopper and exterior of spreader and

dry off before storing.

2. Store in a clean, dry area.

CAUTION: DO NOT inate tires beyond

the maximum recommended pressure

printed on side of tire.

CLEANING

4. Rinse inside of hopper and exterior of spreader and

dry off before storing.

LUBRICATE (See gure 15)

5. Lightly apply automotive grease as needed to the

sprocket and gear.

6. Oil the nylon bushings on the vertical sprocket shaft

and on the axle at least once a year, or more often as

needed.

7. Oil right hand (idler) wheel bearing at least once a year

or more often as needed.

MAINTENANCE

STORAGE

REPLACING SLOTTED GEAR

1. If the axle, slotted gear and sprocket assembly is disas-

sembled, mark down the positions of the parts as they

are removed.The drive wheel and sprocket positions in

relation to the slotted gear determine which direction

the spreader plate will spin. Be sure to reassemble

them in their original positions. (Refer to gure 3 on

page 4.) Use shim washers (Ref. no. 21 on pages 10

and 11) as needed for minimum backlash. Add grease

to gear and sprocket.

GREASE

OIL

SERVICE AND ADJUSTMENTS

SHAFT SUPPORT PLATE

SLOTTED GEAR

LOCKED UP SPREADER

1. Turn the spreader over so that the wheels are off the

ground.

2. Loosen all three nuts on the shaft support plate just

enough so that the bolts can be turned easily with a

wrench but cannot be turned by hand.

3. Spin the drive wheel and note how freely it spins and

how much noise the slotted gear makes.

4. To free up the wheel and gear, tap gently on the front

or rear edge of the shaft support plate to move it

slightly forward or backward. You can also tap at the

corners of the plate to angle it slightly.

5. Spin the drive wheel after each adjustment to see if it

spins more freely and if the gear noise is reduced.

6. Continue making slight adjustments until you nd the

position where the drive wheel spins most freely and

the gear makes the least noise.

7. Secure the shaft support plate in this position by

retightening all three nuts that you loosened.

FIGURE 16

REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02143

21 21

27 36

14 15

Inhaltsverzeichnis

Andere Agri-Fab Streuer Handbücher

Agri-Fab

Agri-Fab 45-0364 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-03152 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-02102 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-02101-101 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-03291 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-2142 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-02114 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-03642 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-04631 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-0301 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-02153-131 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-02141 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-0460 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-0414 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-0324 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-02103 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-0566 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-03151 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-0329 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-02101-101 Bedienungsanleitung

Agri-Fab

Agri-Fab 175 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-0187 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-02113 Bedienungsanleitung

Agri-Fab

Agri-Fab 45-02102-101 Bedienungsanleitung

Beliebte Streuer Handbücher anderer Marken

PEQUEA

PEQUEA GT-100 Bedienungsanleitung

Herculano

Herculano H2RS9 Bedienungsanleitung

Epoke

Epoke SKE8 Bedienungsanleitung

GEA

GEA EL44 Technisches Datenblatt

Boss Snowplow

Boss Snowplow TGS 800 Bedienungsanleitung

Fisher

Fisher EMERSON 168 Series Bedienungsanleitung

Fisher

Fisher POLY-CASTER 78601 Bedienungsanleitung

TurfEx

TurfEx RS7200 Betriebsanleitung

Ferris

Ferris Pathfinder Series Bedienungsanleitung

Fayat Group

Fayat Group DYNAPAC S100 Fehlerbehebungshandbuch

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Installations- und Betriebshandbuch

EASTMAN

EASTMAN CR 500 Bedienungsanleitung

Nogueira

Nogueira RoyalFlow-600 Bedienungsanleitung

Buyers

Buyers TGS05B Bedienungsanleitung

Magnum

Magnum V-BOX PV Series Beilage

Meyer's

Meyer's VB280 Bedienungsanleitung

SnowEx

SnowEx VX-4210 Bedienungsanleitung

Kramer

Kramer VM-400HDCP Bedienungsanleitung