AgSense Aqua Trac Pro Bedienungsanleitung
2013-18 Aqua Trac Pro/Lite
Flowmeter Wiring Manual
Revised January 1, 2018
Items Covered In This Manual:
Page 2: Netafim/Dwyer Mechanical Flow Meter Wiring
Page 3: Netafim Octave Flow Meter Wiring
Page 4-8: GF Signet 8550 Flow Transmitter Wiring
Page 9: McCrometer Mechanical Flow Meter Wiring
Page 10-11: Seametrics AG2000, AG3000/Valley Flow Meter
Page12-13: Endress Hauser Promag P 50/53 Flow Meters
Page 14-15: Siemens MAG5000 Flow Meters
Page 16-18: Seametrics PE102/FT520 Flow Meter Wiring
Page 19-21: GF Signet 9900 Flow Transmitter Wiring
Page 22-23: GF Signet 2551 Mag Meter Wiring
Page 24: McCrometer FlowCom Flow Meter Wiring
Page 25-26: McCrometer McMag 3000/EA-618 Flow Meters
Page 27-28: Siemens Sitrans FM MAG 8000 Wiring
Page 29-31: Greyline AVFM 5.0 Flow Meter Wiring
Page 32-33: Senninger Flow Wise SC-3 Flow Meter Wiring
Page 34-35: Banjo MFM 300DC Flow Meter Wiring
Page 36-37: Seametrics FT415 Flow Meter Wiring
Page 38-40: Sparling Tiger Mag Flow Meter Wiring
Page 41-42: Sparling FT194 Flow Meter Wiring
Page 43: Generic Flow Meter Wiring
Wire Connections for the Netafim/Dwyer Mechanical
Flow Meter
(two wire magnetic reed-switch style)
1.Install the Black Wire from the Netafim/Dwyer Flow Meter into any
terminal marked GND as shown in the picture above.
2.Install the Red Wire from the Netafim/Dwyer Flow Meter into the
terminal marked RAIN as shown in the picture above.
Page 2
Wire Connections for the Netafim Octave Flow Meter
(with pulse output module)
1.Install the Black Wire from the Netafim Flow Meter into any terminal
marked GND as shown in the picture above.
2.Install the Red Wire from the Netafim Flow Meter into the terminal
marked RAIN as shown in the picture above.
3.Cut off and/or tape off the Green Wire from the Netafim Flow meter
so that it cannot touch anything.
4.The label on the inside of the Netafim Flow Meter lid will show how
many gallons per pulse that output1 (the red wire) is programmed to
do. You will need that info when configuring this unit on Wagnet.
Page 3
Wire Connections for the GF Signet/Senniger
8550 Flow Transmitter
1.Install the Power Supply, and Flow Meter wires into the GF Signet
8550 Unit as shown above.
2.Install a Red wire into terminal 5 (output+) of the 8550 Unit as shown
above. This wire will connect to the AgSense unit in the steps below.
3.Install a Black wire into terminal 6 (output-) of the 8550 Unit as
shown above. This wire will connect to the AgSense unit in the steps
on the next page.
Page 4
Wire Connections for the GF Signet/Senniger
8550 Flow Transmitter Cont.
1. Install the Black Wire from the GF Signet 8550 Flow Transmitter into
any terminal marked GND as shown in the picture above.
2. Install the Red Wire from the GF Signet 8550 Flow Transmitter into
the terminal marked FLOW as shown in the picture above.
3. Setting up the 8550 Flow Transmitter “calibrate”and “options”
menus –use the charts below to correctly set up the menus in the
8550 Flow Transmitter –you must do this for the AgSense unit to
work properly.
Page 5
Page 6
Page 7
Page 8
Wire Connections for the McCrometer Mechanical
Flow Meter with EA-631-xxx module
The Aqua Trac unit does not support the
McCrometer EA-631 Pulse Module –The new part
number for mechanical McCrometer flow meters is
EA-618-02.
Please use the EA-618-02 Pulse Module for
mechanical flow meter installations.
Please see page 26 for EA-618-02 Wiring.
Page 9
Andere Handbücher für Aqua Trac Pro
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere AgSense Messgerät Handbücher
