AirLive MD-3025-IVS Bedienungsanleitung
MD-3025-IVS
Trip Zone Guide
Version 1.0
MD-3025-IVS Trip Zone Setup Guide
1
MD-3025-IVS
Trip Zone Guide
1. Overview
The MD-3025-IVS has built-in video analytic function for Trip Zone. It is a standalone
function built into the camera’s firmware without the need for external software or device.
The Trip Zone function can be used to detect people or vehicles crossing the restricted
area or boundary. This guide will focus on using MD-3025-IVS’s “Trip Zone”function in
places like one-way traffic, railway station platform, exit of parking lot, highways, privacy or
military instruction.
The Trip Zone function works by defining 2 zones on the video image. When the system
detects an object crossing the center border between 2 zones, it will send an alert message
to notify the administrator within seconds. It can detect object from “Zone1 to Zone2”,
“Zone2 to Zone1”, or both directions.
The important factors for successful installations are:
Choose the appropriate camera viewing angle.
Choose the appropriate camera height (distance).
We will guide you through the procedure in the following articles.
Wrong Way
Detection
MD-3025-IVS Trip Zone Setup Guide
2
2. Hardware Installation Guidelines
The followings are basic installation guidelines for best Trip Zone function. However, if
your environment cannot meet the recommended conditions, it can still work with
reasonable accuracy.
1. Make sure the appropriate viewing angle.
․For human beings, camera can be installed from right above the area to
the side of the area.
․If you install the camera to the side of the area, horizontal detection will be
our suggestion.
MD-3025-IVS Trip Zone Setup Guide
3
․For vehicles, camera can be installed from right above the area to 45
degrees oblique angle.
․For 45 degrees angle, you can choose a horizontal or vertical detection.
2. Make sure the appropriate camera height (distance).
People
Vehicles
Viewing Angle
Distance (Min.)
Viewing Angle
Distance (Min.)
90 degrees on top
2.5M
90 degrees on top
9M
45 degrees
3M
45 degrees
5M
horizontal
3M
horizontal
Not Recommend
Note: The minimum distance is for reference only.
MD-3025-IVS Trip Zone Setup Guide
4
3. Camera Configuration
3.1 Finding camera using AirLive IP Wizard
The IPCAM default IP address is 192.168.1.100，but this address can change when there is
DHCP server(router) in your network. Therefore, please install AirLive IP wizard to find your
camera.
1. Install the “AirLive IP Wizard” from the installation CD or download it from this link.
2. Run the “setup.exe” and open the AirLive IP Wizard.
3. The IP Wizard will auto search and list out the camera found. Double click on the camera
that you want to configure.
4. The IPCAM’s web configuration will open automatically after double click. Please enter
the “admin” for username and “airlive” for password.
5. After entering the correct username and password. You will enter the camera’s web
configuration page. When prompted to install “Media Control” from “OvisLink Corp”,
please select “Yes” to install.
3.2 Enable Camera’s Video Analytic function
Please use Internet Explorer as the default browser. If you are using IE 11, please go to
“Setup->Compatibility View Settings” and add the camera’s IP address to the list.
Please follow the step below to enable camera’s video analytics function.
MD-3025-IVS Trip Zone Setup Guide
5
1. Click on “Configurations” on left menu bar
2. Click on “Video” on the left menu bar and select “enable” Intelligent Video Analytics.
3.3 Setting Resolution and Frame Rate
On the video page, it is important to set the resolution and frame rate correctly.
Please remember to click on “Apply” button after finish settings.
Installation Site
Main Stream
Resolution
Main Stream
Frame Rate
Second Stream
Frame Rate
highways, railway station
platform or military instruction
720P
15FPS
15FPS
exit of parking lot, one-way
traffic or privacy property
1080P
15FPS
15FPS
!
MD-3025-IVS Trip Zone Setup Guide
6
3.4 Configure Trip Zone Function
Please go to “Video Analytics” menu and select “Trip Zone”.
Below is the main page of Trip Zone.
The first step is to set the zones according to your environment. The controls are separated
in Zone Area and Zone Settings as indicated above.
Zone Area
Zone
Settings
Please remember to press “Apply”
after change settings, otherwise the
settings won’t take effect.
MD-3025-IVS Trip Zone Setup Guide
7
Zone Settings
Rotate Mode: this is the default mode. When you click inside the “Zone Area”, you can
rotate, move, and resize the zone by holding the “change points”.
Transform Mode: In this mode, you can freely change the shape of the zones to fit
your installation site.
Directionality: The camera’s Trip Zone function can detect an object crossing from
one zone to another. You can choose to detect from Zone1 to Zone2, Zone2 to Zone 1,
or both directions. You must first click on the zone block inside the Zone Area
first before you are allowed to choose the direction.
Click and hold inside
the zone to move the
block
Click and hold the
change points to rotate
or resize the zones.
Click inside the zones to
activate edit mode
Click and hold inside
the zone to move the
block
Click inside the zones to
activate edit mode
Click and hold the
change points to
change the shape of
the zones
MD-3025-IVS Trip Zone Setup Guide
8
※Please enlarge the Zone 1 and Zone 2 as big as possible. The bigger zone is
more accuracy.
Zone size is big.
Zone size is too small.
※Please extend the length of the moving path as long as possible.
The length of the moving path is longer.
The length of the moving path is too short.
MD-3025-IVS Trip Zone Setup Guide
9
※If the wrong way direction is from Zone 1 to Zone 2, user can set bigger Zone 1 to
increase the accuracy.
Zone 1 size is bigger
After you set the zone area correctly, the next step is to calibrate the object size according
to your installation.
Calibration
Click on either “Min. Size” or “Max. Size” window to change the size of the objects.
Max Size: Object larger than this size will be counted as more than one object.
Min Size: Object smaller than this size will not be counted.
Andere Handbücher für MD-3025-IVS
2
Inhaltsverzeichnis
Andere AirLive Sicherheitskamera Handbücher
AirLive
AirLive MD-3025 Bedienungsanleitung
AirLive
AirLive VD-2028 Montageanleitung
AirLive
AirLive FE-501DM Bedienungsanleitung
AirLive
AirLive CU-720IR Bedienungsanleitung
AirLive
AirLive OD-2025HD Bedienungsanleitung
AirLive
AirLive WL-1200CAM Bedienungsanleitung
AirLive
AirLive WL-5420CAM Bedienungsanleitung
AirLive
AirLive FE-201DM Bedienungsanleitung
AirLive
AirLive BU-3028 Bedienungsanleitung
AirLive
AirLive FE-200DM Bedienungsanleitung
AirLive
AirLive BU-3026 Bedienungsanleitung
AirLive
AirLive SmartCube 300W Installations- und Benutzerhandbuch
AirLive
AirLive FE-200VD Bedienungsanleitung
AirLive
AirLive MD-3025 Bedienungsanleitung
AirLive
AirLive FE-201DM Bedienungsanleitung
AirLive
AirLive BU-3128 Bedienungsanleitung
AirLive
AirLive AIRCAM OD-600HD Bedienungsanleitung
AirLive
AirLive MD-3025 Bedienungsanleitung
AirLive
AirLive SmartCube 300W Einrichtungshandbuch
AirLive
AirLive MD-720 Bedienungsanleitung
