Alcatel-Lucent 9364 Bedienungsanleitung

 

$/&$7(//8&(17





 !

"#$%$$&'(()

 *#+,-

$OFDWHO/XFHQW²3URSULHWDU\

. / //-0,

 

12

*HQHUDOSUHFDXWLRQVIRULQVWDOODWLRQSURFHGXUHV



•

Read and understand all instructions.

•

Follow all warnings and instructions marked on this product.

•

Installation and maintenance procedures must be followed and performed by trained

personnel only.

•

The equipment must be provided with a readily accessible disconnect device as part

of site preparation.

•

Grounding and circuit continuity is vital for safe operation of the equipment. Never

operate the equipment with grounding/bonding conductor disconnected.

•

Install only equipment identified in the product's installation manual. Use of other

equipment may result in an improper connection which could lead to fire or injury.

•

Use caution when installing or modifying telecommunications lines.

•

The product has multiple power inputs. Before servicing, Disconnect all inputs to

reduce the risk of energy hazards.

•

For continued protection against risk of fire, all fuses used in this product must be

replaced only with fuses of the same type and rating.

•

Never install telecommunications wiring during a lightning storm or when conditions

are wet.

•

Never touch uninsulated wiring or terminals carrying direct current or ringing current,

and never leave this wiring exposed. Protect and tape uninsulated wiring and

terminals to avoid risk of fire, electrical shock, and injury to personnel.

•

Never spill liquids of any kind on the product.

•

To reduce the risk of an electrical shock, do not disassemble the product. Opening

and removing covers and/or circuit boards may expose you to dangerous voltages or

other risks. Incorrect reassembly can cause electrical shock when the unit is

subsequently used.

9364 Metro Cell Outdoor Quick Start Installation Guide

$/&$7(//8&(17  

015-==$  

,668( 1RYHPEHU 

$

  

ABOUT THIS DOCUMENT

3XUSRVH

The purpose of this document is to provide quick start hardware installation instructions

for the Alcatel-Lucent 9364 Metro Cell Outdoor (V2 850/1900MHz and 2100MHz).

HODWHGLQIRUPDWLRQ

HIHUWRWKLVGRFXPHQW $WWKLVORFDWLRQ )RUPRUHLQIRUPDWLRQRQ

Alcatel-Lucent W-CDMA System - Safety

Guide, 401-382-880

http://support.alcatel-lucent. com Safety guidelines and the catalog of

hazard statements that appear in the

Alcatel-Lucent UMTS customer

documents.

Alcatel-Lucent 9364 Metro Cell Outdoor (V2

850/1900MHz and 2100MHz) - Installation

and Commissioning, 3MN-01124-0201-

RJZZA

http://support.alcatel-lucent. com Installation and commissioning

procedures for the 9364 Metro Cell

Outdoor

Alcatel-Lucent 9363/9364 Metro Cell

Indoor and Outdoor - Troubleshooting,

3MN-01123-0200-UFZZA

http://support.alcatel-lucent. com Troubleshooting procedures for the

9363 Metro Cell Indoor and 9364

Metro Cell Outdoor

Standard for Installation of Lightning

Protection Systems, NFPA

http://support.alcatel-lucent. com Lightning protection systems

Recommended Practices on Surge Voltages

in Low Voltage AC Power Circuits, IEEE

C62.41 (Latest Edition)

http://support.alcatel-lucent. com Power

7HFKQLFDOVXSSRUW

For technical support, contact your local Alcatel-Lucent customer support team. See the

Alcatel-Lucent Support web site (http://www.alcatel-lucent.com/support/) for contact

information.

9364 Metro Cell Outdoor Quick Start Installation Guide

  $/&$7(//8&(17

  015-==$ 

  ,668( 1RYHPEHU

Pre-installation information

3URGXFWGHOLYHU\FRQWHQWV

Unpack and examine the V2 Metro Cell Outdoor. If you notice any damage, or missing

items as listed in the Packing List, immediately notify the carrier that delivered the unit

and contact your Alcatel-Lucent representative.

The V2 Metro Cell Outdoor packaging contains:

•

The V2 Metro Cell Outdoor access point

•

R2CT mini short plug

•

Pole/Wall mounting kit (excluding collar kit)

Note: The Alcatel-Lucent 9364 Metro Cell - Outdoor 1900/850 MHz variant interface

panel will have a SMA connector for external GPS antenna and additional LEDs.

9DULDEOHSDUWVDQGDQFLOODU\LWHPV

In addition to the standard delivered parts the following variable and ancillary items are

available:

•

Antennas (2dBi, 4dBi, or 6dBi omni directional antenna)

•

External GPS antenna with 1.48 feet (450 mm) of cable (1900/850 MHz variant only)

•

RF jumper, 2 meters

•

A PoE+ power injector, with user guide

•

Pole mounting collar kit

9364 Metro Cell Outdoor Quick Start Installation Guide

$/&$7(//8&(17  

015-==$  

,668( 1RYHPEHU 

•

Overcasing kit (optional cosmetic cover to conceal the unit mounted)

9HULI\VLWHSUHSDUDWLRQ

The following site preparation requirements should be checked and met before the

installation of the V2 Metro Cell Outdoor can begin. If some of the requirements are not

met, the installer must do so now:

•

Ensure equipment is planned to be installed as high as possible to avoid obstructions

•

Consider nearby sources of interference

•

Ensure adequate clearance is provided for service access

•

Ethernet cable has been routed and is in place

•

Ground cable has been routed and is in place

•

Site specific fixing materials (screws, washers, wall plugs) for wall mounting the

Metro Cell - Outdoor are available

,QVWDOODWLRQWRROVUHTXLUHG

The following is a list of the tools that may be used during installation:

•

Drill (Pneumatic Hammer) and assorted drill bits

•

Pliers

•

Adjustable spanners

•

Screwdrivers (power and/or manual):

-Flat blade

-Torx, T10, T20

•

HRS (Hirose) - HT206/TM21p-88p crimping tool (for cable and shielded crimping)

•

Torque wrench set to cover:

-0.7 N.m - 1.1 N.m (6.2 lbf.in - 9.7 lbf.in)

-3 N.m - 3.5 N.m (26.5 lbf.in - 31 lbf.in)

-15N.m (132.8 lbf.in)

•

Data cable tester for shielded RJ45 (optional)

•

Measuring tape

•

Marker, to mark wall mounting holes

•

Level

•

Hammer

•

PIB (self-amalgamating) tape and 3M Super 33+ vinyl tape

•

Ear protectors and safety goggles/glasses

•

Assorted cable ties

9364 Metro Cell Outdoor Quick Start Installation Guide

  $/&$7(//8&(17

  015-==$ 

  ,668( 1RYHPEHU

To mount the hardware to a wall

3XUSRVH

This topic describes the procedures to be followed when installing the Metro Cell

Outdoor onto a solid concrete wall.

Important! The Metro Cell Outdoor weighs less than 2kg (4.41 lbs) and can be easily

mounted onto any flat, sturdy wall, either directly, or by using the wall mounting kit (in

circumstances where the device needs to be mounted away from the wall).

However, various building materials and construction methods dictate that the device be

fastened to the wall with appropriate mounting hardware. It is the responsibility of the

customer to provide any necessary support material and structures to ensure that the

installation will be in compliance with Building Officials and Code Administrators

(BOCA), Uniform Building Code (UBC), and all local codes.

%HIRUH\RXEHJLQ

Before installation begins carry out the following:

•

Ensure site preparation actions have been carried out, see Pre-installation information.

•Record the 11 digit serial number and the 12 digit MAC Address, displayed on the

product label, before mounting the Metro Cell - Outdoor.

•The following actions can be carried out depending on installation configuration and

access:

oIf the Metro Cell overcasing is to be installed, attach the overcasing support

plate before wall mounting (refer to the Overcasing installation instructions,

3MN-01124-0202-RJZZA).

Note: The overcasing can act as a solar shield and is strongly recommended

for locations with ambient temperature above +33°C to avoid a performance

drop and a reduced life expectancy of the Metro Cell Outdoor.

oIf the installation location has difficult or restrictive access then the antenna

and R2CT mini short plug can be fitted before mounting the Metro Cell, see

Metro Cell Outdoor cabling.

:DOOPRXQWLQVWDOODWLRQ



Falls can occur when working at heights resulting in serious personal injury or death.

9364 Metro Cell Outdoor Quick Start Installation Guide

$/&$7(//8&(17  

015-==$  

,668( 1RYHPEHU 

To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safe

work practices and wear appropriate fall protection equipment.



6WHSV

To mount the device onto a wall or flat surface, perform the following steps.

At the selected installation location:

,I« 7KHQ«

The Metro Cell is to be mounted directly

onto a wall.

Mark the points on the wall for the four fixing

holes.

The Metro Cell is to be mounted onto a

wall using the wall mounting kit.

Use the wall mounting bracket as a guide to mark

the points on the wall for the four bracket fixing

holes.

Check the horizontal position of the marked holes with a level. Drill holes at the marked

points and insert wall plugs into the fixing holes.



,I« 7KHQ«

The Metro Cell is to be mounted directly

onto a wall.

Proceed with the next Step.

The Metro Cell is to be mounted onto a

wall using the wall mounting kit.

Attach the wall mounting bracket to the wall using

appropriate screw fixings.

Note: Depending on the wall the device is to be

mounted onto, different screw fixings might be

needed. After site survey these mounting

accessories must be procured locally.

Using the lifting point on the device align the bolt holes on the Metro Cell with the

drilled wall bolt holes or, if the wall mounting bracket is used, with the bolt holes on the

bracket:

9364 Metro Cell Outdoor Quick Start Installation Guide

  $/&$7(//8&(17

  015-==$ 

  ,668( 1RYHPEHU

Attach the device to the wall mounting bracket using the supplied screws or directly onto

the wall using appropriate screw fixings.

Note: Depending on the wall the device is to be mounted onto, different screw fixings

might be needed. After site survey these mounting accessories must be procured locally.

After mounting the Metro Cell Outdoor to the wall the cables must be connected.

Continue with, Metro Cell Outdoor cabling.

(

1 ' 

) 

7 ( 3 6



9364 Metro Cell Outdoor Quick Start Installation Guide

$/&$7(//8&(17  

015-==$  

,668( 1RYHPEHU 

3,445/

3XUSRVH

This topic describes the procedures to be followed when installing the Metro Cell

Outdoor onto a pole.

The Metro Cell Outdoor is less than 2kg (4.41 lbs) and can be easily mounted on a pole

(48mm to 114mm in diameter) using the supplied pole mounting kit.

%HIRUH\RXEHJLQ

Before installation begins carry out the following:

•

Ensure site preparation actions have been carried out, see Pre-installation information.

•Record the 11 digit serial number and the 12 digit MAC Address, displayed on the

product label, before mounting the Metro Cell Outdoor.

•The following actions can be carried out depending on installation configuration and

access:

oIf the installation location has difficult or restrictive access then the

antenna and R2CT mini short plug can be fitted before mounting the

Metro Cell, see Metro Cell Outdoor cabling.

3ROHPRXQWLQVWDOODWLRQ



Falls can occur when working at heights resulting in serious personal injury or death.

To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safe

work practices and wear appropriate fall protection equipment.

6WHSV

To mount the device onto a pole, perform the following steps.

Using the supplied pole bracket thread metal pole bands through the pole channel groove

on the pole bracket. Recommended pole band clips, 16mm stainless steel of type Jubilee

High Torque or JCS HI-Torque or Tamtorque

At the selected installation location, assemble the bracket onto the pole as shown,

ensuring the bracket metal bands are securely tightened. Recommended torque setting: 15

N.m (132.8 lbf.in).

9364 Metro Cell Outdoor Quick Start Installation Guide

  $/&$7(//8&(17

  015-==$ 

  ,668( 1RYHPEHU

Using the lifting point on the device align the bolt holes on the Metro Cell with the pole

bracket holes. Bolt the Metro Cell onto the pole bracket using 4 x M5x25 Screws and

4x5.2mmWashers.

After mounting the Metro Cell Outdoor to the pole the cables must be connected.

Continue with, Metro Cell Outdoor cabling.

(

1 ' 

) 

7 (



Tip:

In order to limit the amount of solar radiation on the

Metro Cell when the device is pole mounted, it is

recommended to orientate the Metro Cell in northerly

direction.

With this orientation the pole mounting bracket acts

as a solar shield.

Andere Handbücher für 9364

Inhaltsverzeichnis

Andere Alcatel-Lucent Drahtloser Zugangspunkt Handbücher

Alcatel-Lucent

Alcatel-Lucent OmniAccess 700 CLI Betriebsanleitung

Alcatel-Lucent

Alcatel-Lucent OAW-AP210 Series Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent AP1320 Series Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OAW-AP224 Bedienungs- und Wartungsanleitung

Alcatel-Lucent

Alcatel-Lucent OAW-AP120 Series Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OAW 320 Series Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniAccess OAW-AP41 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent AP-120 Series Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OAW-AP228 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniAccess AP60 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniAccess AP 70 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OAW-AP277 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent Stellar AP Series Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OAW-IAP92 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OAW-AP120 Series Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniAccess AP80 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OAW-AP204 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 9764 Series Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 9962 Handbuch

Alcatel-Lucent

Alcatel-Lucent 4080 IP-DECT Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OmniAccess AP92 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent OAW-1200BGE Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent AOS-W 3.4 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 9763 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung