Alcatel OneTouch Home H200 Bedienungsanleitung

User Manual

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one of the following measures:

·Reorient or relocate the receiving antenna.

·Increase the separation between the equipment and receiver.

·Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

·Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. The antenna used for this transmitter must be installed

to provide a separation distance of at least 20 cm from all persons and must not be

co-located or operating in conjunction with any other antenna or transmitter.

There is no country code option in the WIFI setting.

In the USA, only 11 channels are available for 802.11 operation, the following table

provides the frequencies for the 11 channels:

Channel Number

Center Frequency

(MHz)

2412

2417

2422

2427

2432

2437

2442

2447

2452

2457

2462

User Manual of Onetouch-H200 3G Router

Table of Contents

1Hardware Description and Device connection..............................2

1.1 Hardware Description....................................................2

1.1.1 LED Indicator Status.............................................2

1.1.2 Interface Description.............................................3

1.2 Device Connection........................................................3

1.2.1 Device Install.........................................................3

2PC Setting......................................................................................4

3WIFI Connection...........................................................................6

4Web Configuration........................................................................7

4.1 Language Setting...........................................................8

4.2 Setup Wizard.................................................................8

4.3 Network Setup.............................................................10

4.3.1 WAN Interface Setup...........................................10

4.4 Wireless Setup.............................................................13

4.4.1 Basic Setup..........................................................13

User Manual of Onetouch-H200 3G Router

1 Hardware Description and Device connection

1.1 Hardware Description

1.1.1 LED Indicator Status

This 3G router contains 8 LED indicators. User can easily check the situation of

device by observing LED indicator’s status

Definition of LED Indicators follows below table.

LED Indicator

Status

Description

PWR

Light

Power on and normal operation

Off

Power off or failure

WPS

Light

Connected

Blink

Connecting

Off

Closed or not used

LAN1/2

Light

Lan port is on without data transporting

Blink

Lan port is on with data transporting

Off

Lan port is off

PPP

Light

Connected

Blink

Data transporting

Off

Connection off

WiFi

Light

WiFi radio is on without data transporting

Blink

WiFi radio is on with data transporting

Off

WiFi radio is off

PHONE

Light

In use

Off

Stand by

2G/3G

Light

Registered on network

User Manual of Onetouch-H200 3G Router

LED Indicator

Status

Description

off

Disconnected to network

1.1.2 Interface Description

Interface and button description follows the below table.

Interface/Button

Description

SIM slot

Place to insert SIM card

VOIP

Voice interface (RJ11) for phone connection

Lan1/2

LAN port for switch, concentrator and PC with network

adaptor

WPS

WPS PBC mode control button.

Reset

By pressing the button for 3-6 seconds, the system will

restore the default setting.

Power

Interface for power adaptor

On/Off

Press for power on/off

1.2 Device Connection

1.2.1 Device Install

Device should be connected by following procedure:

Step 1: insert the RJ45 cable in package to the LAN port of your device

Step 2: insert another port of RJ45 cable to your PC

Step 3: connect the power adaptor to the power slot of your device

User Manual of Onetouch-H200 3G Router

2 PC Setting

In default setting, the IP address of LAN of the device is 192.168.1.1, DNS server

address is 255.255.255.0，DHCP Server on.

When PC connected to Onetouch-H200, normally the user needs to set the TCP/IP

of PC according to follow procedure.

Step 1: Click the right bottom as red part, then click “Open Network and Sharing

Center”.

Step 2:Click “Local Area Connection”

Step 3: Click the “Properties”of Ethernet, then double-click “TCP/IPv4”

User Manual of Onetouch-H200 3G Router

Step 4: Normally the user should choose “Obtain an IP address automatically, then

Click “OK”. Also the user can choose “Use the following IP address”as below

pictures, set “IP address”as 192.168.1.X (any figure from 2-254), DNS server

address as 255.255.255.0.

Step 5: after configuration, select “Start”, input “ping 192.168.1.1”in command to

check if PC and 3G router has been right connected.

User Manual of Onetouch-H200 3G Router

Note:

192.168.1.1 is the default IP address of LAN of the 3G router. If the IP address has

been changed, please modify the IP address to current one.

Step 6: if connected successfully, the page will show like below.

3 WIFI Connection

The connection of WIFI adaptor of PC to OneTouch-H200 should follow below

steps.

Step 1: Click “WIFI connection”in right bottom of desktop.

User Manual of Onetouch-H200 3G Router

Step 2: Choose the right WIFI hotspot, click “Connect”, when it shows “connected”,

it means PC has been connected to WIFI.

Note:

Default SSID ofOneTouch-H200 is H200-XXXX (XXXX is the last four digits of its

Mac)

Step 3: If you have problem with the SSID of the device, please log on the device,

choose “Wireless Setup”-“Basic Setup”, then check the current SSID.

4 Web Configuration

Inhaltsverzeichnis

Andere Alcatel Netzwerk-Router Handbücher

Alcatel

Alcatel SpeedTouch 510 Bedienungsanleitung

Alcatel

Alcatel SPEEDTOUCH 710 Bedienungsanleitung

Alcatel

Alcatel SpeedTouch 610 Bedienungsanleitung

Alcatel

Alcatel SpeedTouch 570 Sicherheitsleitfaden

Alcatel

Alcatel G-010G-P Bedienungsanleitung

Alcatel

Alcatel LINKHUB HH71V1 Bedienungsanleitung

Alcatel

Alcatel Speed Touch 591s Bedienungsanleitung

Alcatel

Alcatel SPEED TOUCH PRO Bedienungsanleitung

Alcatel

Alcatel SPEED TOUCH PRO Bedienungsanleitung

Alcatel

Alcatel OmniAccess 601 Bedienungsanleitung

Alcatel

Alcatel 3EC 16964 AAAA-AAZZA Bedienungsanleitung

Alcatel

Alcatel Y901NB Bedienungsanleitung

Alcatel

Alcatel SPEED TOUCH PRO Bedienungsanleitung

Alcatel

Alcatel SPEED TOUCH 710 Bedienungsanleitung

Alcatel

Alcatel OmniAccess 600- series Bedienungsanleitung

Alcatel

Alcatel SPEED TOUCH PRO Bedienungsanleitung

Alcatel

Alcatel Linkhub HH40V Bedienungsanleitung

Alcatel

Alcatel OS6400-48 Installationshandbuch

Alcatel

Alcatel Router Bedienungsanleitung

Alcatel

Alcatel LINKHUB HH71VM Bedienungsanleitung

Alcatel

Alcatel LINKZONE 2 Bedienungsanleitung

Alcatel

Alcatel AST570 Bedienungsanleitung

Alcatel

Alcatel Omni Switch/Router Bedienungsanleitung

Alcatel

Alcatel Speed Touch Home Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung