Alecto DBX-88eco Bedienungsanleitung

USERS MANUAL

DBX-88eco

LCD Language:

Depending on the purchased version, the LCD language might not be

English on start-up. Please see chapter 4.3 on page 8 how to change the

language of your DBX-88 eco.

1 ECO MODE

This Alecto DBX-88 ECO babyphone is equipped with an unique ECO

mode. Already in normal operation mode, the baby-unit stops transmis-

sion when the baby is not crying. In Full Eco mode it even suppresses

the controlling signals between the baby-unit and the parent unit, so no

transmitting at all.

Next to the Full eco mode, you can set the output power. In case you are

at home with your baby not far away, you can set the babyphone in half

range mode, with low transmitting power and reduced power consump-

tion. In case the baby is not close to you, you may switch to full range.

Attention: once the baby produces noise, the baby-unit is activated and

contacts the parent unit. This causes a small delay which means that

short sounds from the baby may not be heard by you. In case you really

want to hear all sounds from the baby room, you must set the sensitivity

to maximum (see chapter 4.6); with this setting the baby-unit is constantly

active.

2 OVERVIEW

2.1 OVERVIEW PARENT UNIT:

1. sound indication LED’s

2. volume up; up button when

programming

3. volume down; down button when

programming

4. button MENU/OK

5. link-check ( ), see below

6. loudspeaker

7. charge contacts

8. battery compartment

9. microphone

10. start/stop lullaby

11. display (see paragraph 2.3)

12. power on/off

13. talk back

Link check :

• ﬂashes when there is no link between baby unit and parent unit or

parent unit is out of range with the baby unit.

• on steadily when linked to the baby unit

• in the full eco mode this lamp only lights when the parent unit actual

receives noise from the baby unit; in idle state this lamp is OFF

during FULL ECO mode

2.2 OVERVIEW BABY UNIT:

1. battery indication: see below

2. display (see paragraph 2.3)

3. built-in nightlight (not visible

when switched-off

4. power on/off

5. microphone

6. DC input for power adapter

7. start-stop lullaby

8. battery compartment (backside)

9. selection lullaby

10. loudspeaker

11. volume up/down

12. temperature sensor (back-

side)

13. page (to page the parent

unit)

14. nightlight on/off

battery indication :

• lights when batteries are installed and the power adapter is connec-

ted to indicate that batteries are being charged (does NOT goes off

when batteries are fully charged)

1314

7 8

2.3 OVERVIEW DISPLAY:

on when night light is enabled

off when night light is disabled

on when lullaby is playing

on when the speaker volume is turned

off; off when the speaker volume is

turned on

on when sound alert is enabled

flashes when sound alert is triggered

indication temperature reading in Celsius or in

Fahrenheit

on when temperature alert is enabled, flashes when

temperature alert is triggered

on when the alarm time/count down timer is set, flashes

when the alarm time/count down timer is arrived

on when the FULL ECO MODUS is enabled

battery indication:

full battery level

2/3 battery level

1/3 battery level

battery empty

parent unit: this indication animates in cycle while charging. baby-unit: this indication does not light

when the power adapter is connected

displaying of the

several functions

and warnings

during use

displaying of the

several settings

during program-

ming

display parent unit display baby-unit

3 INSTALLATION

3.1 PARENT UNIT:

The parent unit is powered by 2 supplied rechargeable batteries. These

batteries are charged through the included power adapter.

ATTENTION:

NEVER install normal batteries in the baby unit. Normal batteries

cannot be charged. Risc of explosion if battery is replaced by an

incorrect type.

1. Remove the belt clip with the help of a small screw-

driver

2. Remove the battery compartment cover.

3. Insert 2 x AAA rechargeable batteries, observing their

polarities, into the battery compartment on the parent

Unit. Only use the supplied batteries with the following

specifications:

voltage / capacity: 1.2V / 750mAh or more

material / size: NiMH, AAA, HR03

4. Replace the battery door on the Parent unit

5. Connect the output plug of the mains adapter to the DC socket on

the side of the baby unit and the mains adapter to the wall mains

supply.

As soon as the battery icon stops animating, the batteries are fully

charged (*). The LED on the charger pod remains on until you lift the

parents unit from the charger pod.

*: for the first time, it is recommended to continue charging for at least 24 hours, even when the

battery icon indicates that the batteries are full.

3.2 BABY-UNIT:

The baby-unit is powered by the supplied power adapter.

Only connect the provided power adapter with the following specificati-

ons: Input: 100-240VAC 150mA; Output: 9VDC 500mA

For portable use you can install 4 pcs RECHARGEABLE batteries.

ATTENTION:

NEVER install normal batteries in the baby unit. Normal batteries

cannot be charged. Risc of explosion if battery is replaced by an

incorrect type.

1. Remove the battery compartment cover.

2. Insert 4 x AA rechargeable batteries, observing their

polarities, into the battery compartment on the parent Unit. Only use

the supplied batteries with the following specifications:

voltage / capacity: 1.2V / 1300mAh or more

material / size: NiMH, AA, HR6, penlite

3. Reattach the battery compartment cover.

4. Connect the output plug of the mains adapter to the DC

socket on the side of the baby unit and the mains adap-

ter to the wall mains supply.

5. The battery indication comes on and charging begins (this LED

remains lit, even when the batteries are fully charged)

Depending on the capacity of the batteries, It will take about 24 hours to

fully charge the batteries.

The power adapter for the baby-unit is inclusive. Rechargeable batteries

for the baby-unit are exclusive.

3.3 RECOMMENDATIONS:

• Never place the baby unit inside your baby’s cot, bed or playpen.

• MAKE SURE THE BABY UNIT AND MAINS ADAPTOR CABLE ARE

ALWAYS OUT OF REACH OF THE BABY.

• Avoid exposure of the units to moisture or liquid.

• Clean the units with a damp cloth.

• Do not expose the units to extreme heat or direct sunlight.

4 USING YOUR BABY MONITOR

Please read these instructions carefully, and be reminded that this baby

monitor is just intended as an aid. It is not a substitute for responsible,

correct parental supervision.

4.1 POWER ON/OFF:

provided the parent unit is off, press and hold

<POWER> for about 2 seconds to switch-ON

the unit

provided the parent unit is on, press and hold

<POWER> for about 2 seconds to switch-OFF

the unit

4.2 LINK CHECK:

As soon as the parent unit is turned on, it starts looking for the baby unit.

1. The link-led blinks and the text [SEARCHING] comes on the

display

2. As soon as the parent unit finds the baby unit, the link-LED lights

steadily

3. In case the parent unit cannot find the baby unit within a period of 30

seconds (because it is not yet switched on, the batteries of the baby-

unit are empty

or the distance is too large), the text [ NOT LINKED]

comes on the display and attention tones sound every 10 seconds.

See also paragraph 4.15.

4.3 LANGUAGE:

It is recommended to ﬁrst set the language so that all text comes on the

LCD in your favorite language. By default the Dutch language is program-

med.

You only have to set the language onto the parent unit, the baby unit will

be synchronized automatically.

press the MENU button 2x

2 sec.

ﬁnd the required language

press the MENU button to conﬁrm and to store

the setting

brieﬂy press the POWER button to end the pro-

gramming mode

4.4 MONITORING:

As soon as the baby unit detects a sound, it will send it to the parent unit.

receiving volume:

press the - button to decrease the volume or

the + button to increase the volume (5 levels +

volume-OFF)

• the icon lights when the volume is set to off

(no sound)

• You will hear an extra beep when the lowest or

the highest level is reached and when you press

the - or + button.

Optical indication:

the sound is also displayed visually by LED’s;

monitoring can therefore be carried out even

when the volume has been reduced or switched

off altogether

4.5 TALK BACK:

press and hold TALK on the Parent unit to speak

to the baby

control the volume on the Baby unit:

press the - button to decrease the volume or the

+ button to increase the volume

- +

Talk

- +

control the volume on the Parent unit:

press the MENU button

ﬁnd the option [ BABY VOLUME ]

press the MENU button

Set the required volume (attention: the actual

volume does not change yet)

press the MENU button to conﬁrm and to store

the setting (only now the new volume setting will

be effective)

brieﬂy press the POWER button to end the pro-

gramming mode

4.6 SENSITIVITY:

You can adjust the sensitivity on the Parent Unit to monitor the sound

from Baby Unit:

press the MENU button

ﬁnd the option [ SENSITIVITY ]

press the MENU button

select the required level

There are ﬁve levels of sensitivity which are

indicated by lighted blocks:

level 1 represents lowest sensitivity

level 4 represents a high sensitivity

level 5 represents the highest sensitivity (the

microphone is activated all the time)

You will hear an extra beep when the lowest or the

highest level is reached and when you press the - or

+ button.

- +

Andere Handbücher für DBX-88eco

Inhaltsverzeichnis

Andere Alecto Babyphone Handbücher

Alecto

Alecto DVM-150 Bedienungsanleitung

Alecto

Alecto DVM200C Bedienungsanleitung

Alecto

Alecto DVM-201 Bedienungsanleitung

Alecto

Alecto DBX-98 Bedienungsanleitung

Alecto

Alecto DBX-37 Bedienungsanleitung

Alecto

Alecto DVM-750 Bedienungsanleitung

Alecto

Alecto DBX-85 eco Bedienungsanleitung

Alecto

Alecto DVM-75 Bedienungsanleitung

Alecto

Alecto DVM-120 Bedienungsanleitung

Alecto

Alecto DVM-370 Bedienungsanleitung

Alecto

Alecto DBX-57 Bedienungsanleitung

Alecto

Alecto DOS-150+ Bedienungsanleitung

Alecto

Alecto DVM-190 Bedienungsanleitung

Alecto

Alecto DVM-80 Bedienungsanleitung

Alecto

Alecto DBX-90 Bedienungsanleitung

Alecto

Alecto IVM-180 Bedienungsanleitung

Alecto

Alecto DVM-210 Bedienungsanleitung

Alecto

Alecto DBX-76 Bedienungsanleitung

Alecto

Alecto DVM-701 Bedienungsanleitung

Alecto

Alecto DIVM-850 Bedienungsanleitung

Alecto

Alecto DBX-112 Bedienungsanleitung

Alecto

Alecto DBX-86 Bedienungsanleitung

Alecto

Alecto DBX-85 eco Bedienungsanleitung

Alecto

Alecto DBX-93 Bedienungsanleitung

Beliebte Babyphone Handbücher anderer Marken

Philips

Philips SCD 469 Bedienungsanleitung

Oricom

Oricom Babysense 7 Bedienungsanleitung

Levana

Levana TW502 Bedienungsanleitung

Luvion

Luvion Essential Bedienungsanleitung

Philips

Philips AVENT SCD841 Bedienungsanleitung

NUK

NUK Eco Control Video Display 550VD Bedienungsanleitung

Lorex

Lorex sweet peek mini Bedienungsanleitung

Mondevices

Mondevices MonBaby 2 Bedienungsanleitung

Famidoc

Famidoc FDBB-V2 Bedienungsanleitung

Graco

Graco iMonitor 2797 Bedienungsanleitung

babymoov

babymoov High Care A014001 Bedienungsanleitung

Ramili

Ramili RV1000 Bedienungsanleitung

Philips

Philips SBC SC364 Bedienungsanleitung

Swann

Swann SW231-FLO Bedienungsanleitung

Badabulle

Badabulle Baby Online 300 m+ Bedienungsanleitung

Philips AVENT

Philips AVENT SCD526/00 Bedienungsanleitung

Uniden

Uniden Guardian UBR223 Bedienungsanleitung

Summer

Summer Day & Night 28470A Bedienungsanleitung