Allen-Bradley 1747-DTAM-E Bedienungsanleitung

(217) 352-9330 | [email protected] | artisantg.com

ARTISAN

TECHNOLOGY

GROUP

Your definitive source

for

quality

pre-owned

equipment.

Artisan Technology

Group

Full-service,

independent

repair

center

with

experienced

engineers

and

technicians

on staff.

buy

your

excess,

underutilized,

and

idle

equipment

along

with

credit

for

buybacks

and

trade-ins

Custom

engineering

your

equipment

works

exactly as

you

specify.

•

Critical

and

expedited

services

•

Leasing

Rentals/

Demos

• In

stock/

Ready-to-ship

•

!TAR-certified

secure

asset

solutions

Expert

team

ITrust

guarantee

100%

satisfaction

All

ademarks,

names, a

s a

earing here

are

e property of

pecti

ner

Find the Rockwell / Allen-Bradley 1747-DTAM at our website: Click HERE

User

Manual

Data Table

Access Module

(Cat. No. 1747-DTAM-E)

Allen-Bradley

Important User Information

Because of the variety of uses for the products described in this

publication, those responsible for the application and use of this

control equipment must satisfy themselves that all necessary

steps have been taken to assure that each application and use

meets all performance and safety requirements, including any

applicable laws, regulations, codes and standards.

The illustrations, charts, sample programs and layout examples

shown in this guide are intended solely for purposes of example.

Since there are many variables and requirements associated with

any particular installation, Allen-Bradley does not assume

responsibility or liability (to include intellectual property

liability) for actual use based upon the examples shown in this

publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the

Application, Installation and Maintenance of Solid-State Control

(available from your local Allen-Bradley office), describes some

important differences between solid-state equipment and

electromechanical devices that should be taken into consideration

when applying products such as those described in this

publication.

Reproduction of the contents of this copyrighted publication, in

whole or part, without written permission of Allen-Bradley

Company, Inc., is prohibited.

Throughout this manualwe use notes to make you awareof safety

considerations:

Attention statements help you to:

• identify a hazard

• avoid a hazard

• recognize the consequences

!ATTENTION: Identifies information about

practices or circumstances that can lead to personal

injury or death, property damage or economic loss.

Important: Identifies information that is critical for successful

application and understanding of the product.

PLC, PLC2, PLC3, and PLC5 are registered trademarks of Rockwell Automation.

SLC, SLC500, PanelView, RediPANEL, and Dataliner are trademarks of Rockwell

Automation.

IBM is a registered trademark of International Business Machines, Inc.

Publication 1747-6.1

Summary of Changes

The information below summarizes the changes to this manual since

the last printing.

To help you find new information and updated information in this

release of the manual, we have included change bars as shown to the

right of this paragraph.

New Information

The table below lists sections that document new features and provide

additional information about existing features, and it shows where to

find this new information.

For New Information On See Chapter

Because users may employ different programming

devices, specific references to Advanced Programming

Software have been removed from this manual.

Preface – Related

Documentation Table and/or

Your Software User Manual

Chapter 8 – Message

Capability

Notice of Class I, Division 2, Groups A, B, C, D

Hazardous Location Certification

Chapter 1 – Data Table

Access Module Overview

Appendix A – Specifications

An updated diagram showing the connection of a DTAM

module to a DH485 network using a link coupler and an

Advanced Interface Converter (1747-NET-AIC). Chapter 2 – Installation and

Power Up

An updated listing of MSG Instruction Error Codes Chapter 9 –Troubleshooting

S-2 Summary of Changes

Publication 1747-6.1

Table of Contents iii

Publication 1747-6.1

Table of Contents

Preface

Who Should Use this Manual . . . . . . . . . . . . . ..................... P-1

Purpose of this Manual . . . . . . . . . . ............................. P-1

Contents of this Manual . . . . . . . ............................. P-2

RelatedDocumentation.................................... P-3

Common Techniques Used in this Manual . . . . . . . . . ...............P-3

Allen-Bradley Support . . . . . . . . . . . ............................. P-4

Local Product Support . . . . . . . . . . . . . . ....................... P-4

Technical Product Assistance . . . . . . . . . . . ....................P-4

Your Questions or Comments on this Manual . . . . . . . ............P-4

Data Table Access Module

Overview Chapter 1

Module Overview . . . . . . ..................................... 1-1

Installation and Power Up Chapter 2

European Union Directive Compliance . . . . . . ..................... 2-1

EMCDirective ........................................... 2-1

Mounting the Module . . . . . . . . . . . ............................. 2-1

Connecting Your Equipment . . . . . . ............................. 2-4

Module Configuration and Adjustments . . . . . . . . . . ................ 2-6

Power-Up Sequence . . . . . . . . . . . . ............................. 2-8

Module Setup Procedure Chapter 3

Keyboard Description . . . . . . . . . . . ............................. 3-1

FactoryDefaultSettings ...................................... 3-2

EnteringtheSetupMode ..................................... 3-3

Selecting the Language . ..................................... 3-4

SelectingtheNodeAddress ................................... 3-4

SettingtheBaudRate........................................ 3-5

SettingtheAutoAttachFunction ............................... 3-5

BacklightingtheLCD ........................................ 3-6

SettingtheMonitorOverrideFunction ........................... 3-6

Accepting Module Setup Parameters . . . . . . . ..................... 3-7

Using the Module Reset . ..................................... 3-7

Attaching to a Processor Chapter 4

Manual Attach Procedure . . . . . . . . . . . . . . ....................... 4-1

AutoAttachProcedure ....................................... 4-2

Ready Attached Screen . ..................................... 4-3

OperatingModeText...................................... 4-3

Backspace Function During Attach Procedure . . . . . . . . ............. 4-3

AttachingtoaPasswordProtectedProcessor ..................... 4-4

iv Table of Contents

Publication 1747-6.1

Monitoring and Modifying

Data Chapter 5

Operating Modes . . . . . . . . . . ..................................5-1

ModifyMode.............................................5-1

MonitorMode.............................................5-1

MonitorOverrideFeature ...................................5-1

LogicalDataFileAddressing ...................................5-3

BackspaceFunctionDuringDataFileAddressEntry ................5-4

QuickAccessAddressing .....................................5-5

EnteringDataFileAddresses ..................................5-7

Entering Input and Output Addresses. . . . . . . . . . ................5-7

EnteringBitAddresses.....................................5-7

EnteringTimerandCounterAddresses........................5-7

EnteringControlRegisterAddresses..........................5-8

EnteringIntegerAddresses..................................5-8

How to Change Displayed Data File Addresses . . . . . . . .............5-9

How to Display Higher and Lower Word Addresses. . . . . . .........5-9

How to Display Different Word Addresses Within Elements. . . . ....5-10

How to Display Different Control Bits Within Elements . . . . . .......5-11

How to Display Different Bit File Addresses . . . . . . . . ............5-12

How to Change Data File Values . . . . . . .........................5-12

How to Change Word Values . . . . . . .........................5-12

How to Change the Sign of a Value . .........................5-14

BackspaceFunctionDuringDataFileValueEntry...............5-14

How to Change Bit Status at the Word Level . . . . . . . ............5-15

CursorRightFunctionDuringBinaryDataEntry.................5-15

How to Change Bit Status at the Bit Level. . . . . . . . . .............5-16

Quick Recall Functions Chapter 6

QuickRecallFunctionOverview ................................6-1

DefiningQuickRecallFunctions ................................6-1

Using Quick Recall Functions . . . . . . . . . . . . . .....................6-2

ClearingQuickRecallFunctions ................................6-3

Processor Control

Functions Chapter 7

Changing the Processor to Run Mode . . . . . . . . . . ..................7-1

Changing the Processor to Program Mode . . . . . . . . . ...............7-2

ViewingProcessorFaults......................................7-2

ClearingProcessorFaults .....................................7-3

Transferring Memory from EEPROM to RAM . . . . . . . . . .............7-4

Transferring Memory from RAM to EEPROM . . . . . . . . . .............7-5

Message Capability Chapter 8

MessageOverview...........................................8-1

ProgrammingtheMSGInstruction...............................8-2

5/02ControlBlockConfiguration ................................8-2

5/03ControlBlockConfiguration ................................8-4

8-WordMessage ............................................8-6

Table of Contents v

Publication 1747-6.1

16-WordMessage........................................... 8-7

12-WordMessage........................................... 8-8

13-WordMessage........................................... 8-9

18-WordMessage.......................................... 8-10

1-WordMessage........................................... 8-11

ApplicationExample1 ...................................... 8-12

ApplicationExample2 ...................................... 8-18

Troubleshooting Chapter 9

Troubleshooting Module Problems Using the Communications LED . . . . 9-1

Troubleshooting Module Problems Using the LCD . . . . . . . ........... 9-3

Troubleshooting Communication Problems Using the LCD . . . . ....... 9-4

Troubleshooting Function Problems Using the LCD . . . . . . . ..........9-7

Troubleshooting MSG Instruction Error Codes . . . . . . . . ............. 9-8

Troubleshooting Processor Faults Using the LCD . . . . . . . .......... 9-11

Specifications Appendix A

OperatingPower............................................ A-1

TemperatureandHumidity .................................... A-1

General Characteristics . . . . . . . . . . ............................. A-2

SLC 500 Data Files and

Logical Addressing Appendix B

DataFiles ................................................. B-1

DataFileTypes.......................................... B-1

AddressStructure......................................... B-2

Data Files 0 and 1 - Outputs and Inputs. . . . . . . . . ...............B-2

DataFile3-Bit........................................... B-5

DataFile4-Timers....................................... B-6

DataFile5-Counters ..................................... B-7

DataFile6-Control....................................... B-8

Data File 7- Integer. . . . . . . . . . . ............................. B-9

Module Display Character

Set Appendix C

DisplayCharacterTable ...................................... C-1

Mounting Template Appendix D

UsingtheTemplate.......................................... D-1

vi Table of Contents

Publication 1747-6.1

Preface

Read this preface to familiarize yourself with the rest of the manual.

This preface covers the following topics:

• who should use this manual

• the purpose of this manual

• common techniques used in this manual

• Allen-Bradley support

Who Should Use this

Manual

Use this manual if you are responsible for designing, installing,

programming, or troubleshooting control systems that use Allen-

Bradley small logic controllers.

You should have a basic understanding of SLC 500 products. If you

do not, contact your local Allen-Bradley representative for

information on available training courses before using this product.

Purpose of this Manual

This manual is a learning and reference guide for the Data Table

Access Module. It describes the procedures you use to access data

file information, change operating modes, monitor and clear

processor faults, and transfer memory with any SLC 500 family

processor.

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley ControlLogix 1756-OF6VI Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1203-GD1 Stücklistenhandbuch

Allen-Bradley

Allen-Bradley POINT I/O 1734-4IOL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-IB8S Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-OW8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-KA2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley DeviceNet 1747-SDN Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Bedienungsanleitung

Allen-Bradley

Allen-Bradley DH485/RS-232C Bedienungsanleitung

Allen-Bradley

Allen-Bradley CENTERLINE 2100 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFM Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1500 1764-MM1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1407-CGCM-DLR Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1757-ABRIO Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2711P-RN6K Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-OW Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-QRD Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-OB8EP Bedienungsanleitung

Allen-Bradley

Allen-Bradley OptiSIS 1711-P05SISID050S Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O PROFIBUS 1794-APBDPV1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-IL Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung