Allen-Bradley FlexLogix 1794-L33 Bedienungsanleitung

Publication 1794-IN002F-EN-P - October 2002

Installation Instructions

FlexLogix Controller System

Catalog number: 1794-L33, 1794-L34 & 1794-FLA

Before You Begin

Use this document as a guide for installing and powering-up your FlexLogix™

controller system. This guide provides installation instructions for both the

FlexLogix controller (1794-L33, -L34) and the FlexLogix extended-local I/O adapter

(1794-FLA). You should already be familiar with the FlexLogix system components.

See the documentation references for additional information.

You must FLASH upgrade the firmware on your FlexLogix controller before you

can use it. The controller ships with firmware revision 1.x but must be upgraded to

match the version of RSLogix 5000 that you are using (e.g. if you are using

RSLogix 5000 V11, you must upgrade your FlexLogix controller firmware to revision

11.x before using it. For more information on upgrading your controller’s firmware,

see page 19.

Tools That You Need

·slotted screwdriver

·phillips screwdriver

·mounting hardware (for mounting a DIN rail)

·drill (for mounting a DIN rail)

·needle-nose pliers

IMPORTANT Installation instructions ship with each FlexLogix component. If

you want the FlexLogix System User Manual, publication

1794-UM001, you can obtain it as follows:

·download an electronic version or place an order over the

Internet: www.theautomationbookstore.com

·contact your local distributor or Rockwell Automation

representative

For information about other publications that may be needed

with the FlexLogix Controller system, see page 27.

Allen-Bradley Replacements

2FlexLogix Controller System

Publication 1794-IN002F-EN-P - October 2002

Important User Information

Because of the variety of uses for the products described in this publication, those

responsible for the application and use of these products must satisfy themselves

that all necessary steps have been taken to assure that each application and use

meets all performance and safety requirements, including any applicable laws,

regulations, codes and standards. In no event will Rockwell Automation be

responsible or liable for indirect or consequential damage resulting from the use or

application of these products.

Any illustrations, charts, sample programs, and layout examples shown in this

publication are intended solely for purposes of example. Since there are many

variables and requirements associated with any particular installation, Rockwell

Automation does not assume responsibility or liability (to include intellectual

property liability) for actual use based upon the examples shown in this

publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application, Installation

and Maintenance of Solid-State Control (available from your local Rockwell

Automation office), describes some important differences between solid-state

equipment and electromechanical devices that should be taken into consideration

when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in whole or part,

without written permission of Rockwell Automation, is prohibited.

Throughout this publication, notes may be used to make you aware of safety

considerations. The following annotations and their accompanying statements help

you to identify a potential hazard, avoid a potential hazard, and recognize the

consequences of a potential hazard:

WARNING

Identifies information about practices or circumstances that can

cause an explosion in a hazardous environment, which may

lead to personal injury or death, property damage, or economic

loss.

ATTENTION

Identifies information about practices or circumstances that can

lead to personal injury or death, property damage, or economic

loss.

FlexLogix Controller System 3

Publication 1794-IN002F-EN-P - October 2002

Handling the FlexLogix System Components

Take these precautions for the environment and enclosure:

IMPORTANT Identifies information that is critical for successful application

and understanding of the product.

ATTENTION

Environment and Enclosure

This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications

(as defined in IEC publication 60664-1), at altitudes up to 2000

meters without derating.

This equipment is considered Group 1, Class A industrial

equipment according to IEC/CISPR Publication 11. Without

appropriate precautions, there may be potential difficulties

ensuring electromagnetic compatibility in other environments

due to conducted as well as radiated disturbance.

This equipment is supplied as "open type" equipment. It must be

mounted within an enclosure that is suitably designed for those

specific environmental conditions that will be present and

appropriately designed to prevent personal injury resulting from

accessibility to live parts. The interior of the enclosure must be

accessible only by the use of a tool. Subsequent sections of this

publication may contain additional information regarding specific

enclosure type ratings that are required to comply with certain

product safety certifications.

See NEMA Standards publication 250 and IEC publication 60529,

as applicable, for explanations of the degrees of protection

provided by different types of enclosure. Also, see the

appropriate sections in this publication, as well as the

Allen-Bradley publication 1770-4.1 ("Industrial Automation

Wiring and Grounding Guidelines"), for additional installation

requirements pertaining to this equipment.

Allen-Bradley Replacements

4FlexLogix Controller System

Publication 1794-IN002F-EN-P - October 2002

Take these precautions to guard against ESD damage:

Removal and Insertion Under Power

While backplane power is applied and the system is operating, you can only install or remove

FLEX I/O modules. The FlexLogix controller, the extended-local I/O adapter, the

communication daughtercards, and the I/O terminal bases are not removable or insertable

under power.

Repeated electrical arcing causes excessive wear to contacts on both the module

and its mating connector. Worn contacts may create electrical resistance that can

affect module operation.

ATTENTION

Preventing Electrostatic Discharge

This equipment is sensitive to electrostatic discharge, which

can cause internal damage and affect normal operation.

Follow these guidelines when you handle this equipment:

·Touch a grounded object to discharge potential static.

·Wear an approved grounding wriststrap.

·Do not touch connectors or pins on component boards.

·Do not touch circuit components inside the equipment.

·If available, use a static-safe workstation.

·When not in use, store the equipment in appropriate

static-safe packaging.

WARNING

When you insert or remove the module while backplane power

is on, an electrical arc can occur. This could cause an explosion

in hazardous location installations. Be sure that power is

removed or the area is nonhazardous before proceeding.

ATTENTION

This Product is grounded through the DIN rail to chassis

ground. Use zinc plated yellow-chromate steel DIN rail to

assure proper grounding. The use of other DIN rail materials

(e.g. aluminum, plastic, etc.) that can corrode, oxidize, or are

poor conductors, can result in improper or intermittent

grounding.

FlexLogix Controller System 5

Publication 1794-IN002F-EN-P - October 2002

What You Need to Do

Before you can install a FlexLogix controller or extended-local adapter, you must:

Install steel, 35 x 7.55mm DIN rails (A-B part number 199-DR1; 46277-3)

where you want to place the FlexLogix system components.

The DIN rails for all FlexLogix system components, including all local and

extended-local I/O modules, must be mounted on a common, conductive

surface to ensure proper electromagnetic interference (EMI) performance.

See 23 and 24 for approximate mounting dimensions and mounting

clearances.

For more information about mounting DIN rails and splitting I/O across DIN

rails, see the FLEX I/O Product Data, publication 1794-2.1

Use DIN rail locks (A-B catalog number 1492-EA35) to meet the shock and

vibrations specifications listed on 21. A pair of DIN locks comes with

the controller.

Mount an appropriate power supply on an appropriate DIN rail. See the

specifications on 21.

To install a FlexLogix controller:

Step 1: Verify That You Have All the Components, see page 6.

Step 2: Install the Battery, see page 7.

Step 3: Install Communication Daughtercards (optional), see page 8

Step 4: Install the Controller, see page 9.

Step 5: Install the Extended-Local Adapter (optional), see page 12.

After you install the FlexLogix controller, you can:

Make an RS-232 Connection to the Controller, see page 15.

Select the Operating Mode of the Controller see page 18.

Monitor the Controller LEDs, see page 19.

Allen-Bradley Replacements

6FlexLogix Controller System

Publication 1794-IN002F-EN-P - October 2002

Step 1: Verify That You Have All the Components

These components ship with the FlexLogix controller:

·1756-BA1 battery and label

·key

·one spring-clip connector plug for 24V power connection

·one screw-terminal connector plug for 24V power connection

·two 1492-EA35 DIN rail locks

The system components you have depend on your application. You might have:

FlexLogix System Component: Description:

1788-CNC, -CNCR for ControlNet communications

1788-CNF, -CNFR for ControlNet communications

1788-DNBO for DeviceNet communications

1788-ENBT for EtherNet/IP communications

1756-CP3

You can also use the 1747-CP3 cable from the SLC product family.

1794-FLA

1794-CE1 (1 foot)

1794-CE3 (3 foot)

communication card

serial cable

FlexLogix extended-local adapt

extended- local I/O cable

FlexLogix Controller System 7

Publication 1794-IN002F-EN-P - October 2002

Step 2: Install the Battery

1. Install a 1756-BA1 battery.

2. Attach the battery label:

a. Write on the battery label the date you install the battery.

b. Attach the label to the inside of the battery compartment.

ATTENTION

Only install a 1756-BA1 battery. If you install a different battery,

you may damage the controller.

WARNING

For safety information on the handling of lithium batteries,

including the handling and disposal of leaking batteries, see

Guidelines for Handling Lithium Batteries, publication AG-5.4.

Store batteries in a cool, dry environment. We recommend 25°C

with 40% to 60% relative humidity. You may store batteries for

up to 30 days between -45°to 85°C, such as during

transportation. To avoid possible leakage, do not store batteries

above 60°C for more than 30 days.

Attach battery here.

top red lead (+)

middle black lead (-)

bottom no connection

Attach label here.

This jumper is for

service use only. Do

not use this jumper.

Allen-Bradley Replacements

8FlexLogix Controller System

Publication 1794-IN002F-EN-P - October 2002

Step 3: Install Communication Daughtercards (optional)

1. Turn off power to the controller.

2. If necessary, remove the blank cover from the communication slot.

3. Slide the communication card into the communication slot. Be sure to line

up the card with the card guides in the controller.

Record which slot you use for the communication card. You need the slot

number when you develop your controller application.

4. Secure the card with the screws to ensure proper grounding. Do not

over-tighten the screws. The maximum torque for the card screws is

4.8-5.2 inch/pounds.

5. After the controller is installed (see 9), you can connect the network cable.

Removing a communication card

If you need to remove a communication card from the controller:

6. Turn off power to the controller.

7. Disconnect all cables from the communication card.

8. Loosen the card screws from the communication card.

9. Remove the card out from the controller.

10. Replace the card with a blank cover or a different communication card.

IMPORTANT For specific information about configuring the communication

card (such as setting a node address), see the installation

instructions for the communication card.

31032-M

slot 1

slot 2

FlexLogix Controller System 9

Publication 1794-IN002F-EN-P - October 2002

Step 4: Install the Controller

1. Position the FlexLogix controller on the DIN rail at a 5°angle and rotate the

controller onto the DIN rail.

2. Press the controller down onto the DIN rail until flush. The locking tabs will

snap into position and lock the controller onto the DIN rail.

If the controller does not lock in place, use a screwdriver or similar device to

move the locking tabs down while pressing the controller onto the DIN rail.

Release the locking tabs to lock the controller in place. If necessary, push up

on the locking tabs to lock.

3. Ground the controller. The DIN rail and the common, conductive surface

behind the DIN rail provide functional ground for the controller. Use the

grounding stud to meet safety ground requirements.

For information about wiring and grounding, see the Industrial Automation

Wiring and Grounding Guidelines publication 1770-4.1.

IMPORTANT You can mount the FlexLogix controller either vertically or

horizontally (as shown).

locking tabs

grounding stud

Equipment grounding conductor

(ground lug with 4mm2(14AWG)

wire) to ground bus

nuts with captive

star washer

Allen-Bradley Replacements

10 FlexLogix Controller System

Publication 1794-IN002F-EN-P - October 2002

4. Make sure power is not applied to the power supply. Connect the

power supply to the controller. This diagram and its related instructions

describe a 1794-PS13 power supply.

a. Connect +24V dc input to the top of the controller connector, terminal A,

to the bottom, left power connector, terminal G.

b. Connect -24V common to top controller connector, terminal B, to the top,

left power connector, terminal E.

c. Use connections Cand Don the controller and connection Fand Hon

the power supply to pass 24V dc power and common to the next module

in the series, if required.

Use the screw-terminal connector plug that comes with the controller to

meet the requirements for installations in Class I, Division 2 locations.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Controller Handbücher

Allen-Bradley

Allen-Bradley 1756-L61S ControlLogix 5561S Bedienungsanleitung

Allen-Bradley

Allen-Bradley powerflex 700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley GuardPLC 1754 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 700H Bedienungsanleitung

Allen-Bradley

Allen-Bradley powerflex 700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1100 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SMC-50 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 40P Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 700S Bedienungsanleitung

Allen-Bradley

Allen-Bradley micrologix 1500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-L71 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Studio 5000 Logix Emulate Betriebsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PLC-5/12 Einrichtungshandbuch

Allen-Bradley

Allen-Bradley iTRAK 5730 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 400 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FlexPak 3000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley AADvance Bedienungsanleitung

Allen-Bradley

Allen-Bradley controllogix 1756-L61 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 22C-B012N103 Bedienungsanleitung

Allen-Bradley

Allen-Bradley GuardPLC 1753 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PLC-5 series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung