Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Installation Instructions

PowerFlex 750-Series Power Jumpers

PowerFlex 750-Series drives contain protective MOVs and Common Mode

Capacitors referenced to ground (see below). To guard against unstable operation

and/or damage, the drive must be properly configured as shown in Table 1 on

page 2.

For additional general information, refer to:

Before proceeding, ensure that all power to the drive has been removed.

R/L1

S/L2

T/L3

PE-A1

PE-A

PE-A2 Frame 8

DC+

DC– PE-B

MOV and AC EMI Capacitor Phase to Ground Common Mode Capacitor to Ground

Title Publication Available Online at …

PowerFlex 750-Series Installation Instructions 750-IN001 www.rockwellautomation.com

/literature

Wiring and Grounding Guidelines for PWM AC Drives DRIVES-IN001

Guarding Against Electrostatic Damage 8000-4.5.2

ATTENTION: This drive contains ESD (Electrostatic Discharge) sensitive

parts and assemblies. Static control precautions are required when

installing, testing, servicing or repairing this assembly. Component

damage may result if ESD control procedures are not followed. If you are

not familiar with static control procedures, reference A-B publication

8000-4.5.2, “Guarding Against Electrostatic Damage” or any other

applicable ESD protection guide.

ATTENTION: Only qualified personnel familiar with adjustable frequency

AC drives and associated machinery should perform maintenance/repair of

the system. Failure to comply may result in personal injury and/or

equipment damage.

ATTENTION: The following information is merely a guide for proper

installation. Rockwell Automation cannot assume responsibility for the

compliance or the noncompliance to any code, national, local or otherwise

for the proper installation of this drive or associated equipment. A hazard

of personal injury and/or equipment damage exists if codes are ignored

during installation.

Rockwell Automation Publication 750-IN011B-EN-P - July 2010

2PowerFlex 750-Series Power Jumpers

Table 1 - Recommended Power Jumper Configurations

To connect or disconnect these devices, refer to pages 4…6.

In addition, on an ungrounded distribution system where the line-to-ground

voltages on any phase could exceed 125% of the nominal line-to-line voltage, an

isolation transformer should be installed. See Wiring and Grounding Guidelines

for PWM AC Drives, publication DRIVES-IN001 for more information on

impedance grounded and ungrounded systems.

ATTENTION: To avoid an electric shock hazard, verify that the voltage on

the bus capacitors has discharged completely before removing/installing

jumpers.

Frames 2…7

Measure the DC bus voltage at the following points (refer to the

Installation Instructions for locations):

•+DC and -DC terminals of the Power Terminal Block

•+DC terminal of the Power Terminal Block and the chassis

•-DC terminal of the Power Terminal Block and the chassis

The voltage must be zero for all three measurements.

Frame 8

Measure the DC bus voltage at the DC+ and DC- TESTPOINT sockets on

the front of the power module (see Installation Instructions for location).

Power Source Type (1)

(1) It is highly recommended to accurately determine the power source type and then configure appropriately.

MOV/Input

Filter Caps

(PE-A)(2)(3)

(2) When MOVs are disconnected, the power system must have its own transient protection to ensure known and

controlled voltages.

(3) Frame 8 drives utilize two jumpers labeled PE-A1 and PE-A2.

DC Bus Common

Mode Caps

(PE-B)

Benefits Of Correct

Configuration on Power

Source Type

Unknown

Default Configuration “A” (see

page 3)

Connected Disconnected See Solid & Non-Solid

Ground points below

Solid Ground

Default Configuration “J” (see

page 3)

•AC fed, solidly grounded

•DC fed from passive rectifier

which has an AC source and

solid ground

Connected Connected •UL compliance,

•Reduced electrical noise,

•Most stable operation,

•EMC compliance,

•Reduced voltage stress on

components and motor

bearings

Non-Solid Ground

•AC fed ungrounded

•Impedance grounded

•High resistive ground

•B phase ground

•Regenerative unit such as

common DC bus supply & brake

•DC fed from an active converter

Disconnected Disconnected •Helps avoid severe

equipment damage when

ground fault occurs

IMPORTANT Common mode capacitors are used to conform with the EMC

directives. Removing these devices may withdraw the associated

directive.

Rockwell Automation Publication 750-IN011B-EN-P - July 2010

PowerFlex 750-Series Power Jumpers 3

Jumper Installation, Removal and Storage

Jumper screws (Frames 2…5),

wires (Frames 6…7) or plugs

(Frame 8) are used to complete

an electrical connection when

installed/connected. When

power jumper screws are not

used, they are stored on the left

interior chassis wall as shown.

When installing a jumper screw or wire, note the recommended torque listed.

Drive Identification

Refer to the drive nameplate and

locate the “Voltage Code” and

“Default Power Jumper

Configuration.” Use this

information to locate the proper

procedure in the following tables.

ATTENTION: Hazard of equipment damage exists if jumpers are not

properly disconnected. For Frames 2…5, completely remove the jumper

screw from the circuit board. On Frames 6…7, secure the disconnected

jumper wire to the standoff provided. On Frame 8, secure the disconnected

jumper plug in the socket provided and the PE-A1 jumper wire to the

standoff provided.

Frames Recommended Torque Recommended Screwdriver/Socket

2…5 1.36 N•m (12.0 lb•in) ±0.14 N•m (1.2 lb•in) 6.4 mm (0.25 in.) flat or T15 Hexalobular

6…8 1.36 N•m (12.0 lb•in) 7 mm socket or T20 Hexalobular

Drive Power Jumpers

Frame 4 Shown

Jumper Screws

Installed

Jumper Screws

Not Installed

Jumper Screw Storage

Cat No. 20G11 N D011 AA0NNNNN

UL Type 1 - only with Debris Hood and Conduit Plate

UL Open Type/IP20 - without Debris Hood and Conduit Plate

Specifications and Custom Catalog Number

representing options installed at factory.

See Nameplate 2 (Located behind HIM)

for equivalent base catalog number and separate options

Nameplate 1:

Mfd. in 2009 on Jan. 19

Series: A

Input: 3 Phase, 47-63Hz

AC Voltage Range

Amps ND (HD)

Power ND (HD)

Output: 3 Phase, 0-400 Hz

AC Voltage Range

Base Frequency (default)

Continuous Amps ND (HD)

60Sec Ovld Amps ND (HD)

3 Sec Ovld Amps ND (HD)

0-400

50 Hz

342-440 432-528

0-460

60 Hz

xxx

xxx xxx xxx xxx

5.5 HP (4 HP) 7.5 HP (5 HP)

N223

Serial Number: xxxxxxxx

Original Firmware: x.xxx

TUV

Rheinland

Product Safety

Production inspected

EN 61800-5-1

Made in the U.S.A. Fac1C

400V Class 480V Class

II (2) G D

Functional Safety

Type approved

Voltage Code

Default Power Jumper Configuration

Code Filtering Default CM Cap

Connection

A Yes Jumper Removed

J Yes Jumper Installed

480V drives must select code "A." Jumpers are

included for field reconfiguration as desired.

Rockwell Automation Publication 750-IN011B-EN-P - July 2010

4PowerFlex 750-Series Power Jumpers

Jumper Settings and Locations

Frame

Voltage

Code

Factory Default Jumper Settings

Power Source TypeCatalog Code “A” Catalog Code “J”

DPE-A Installed

PE-B Not Installed PE-A Installed

PE-B Installed Solid Ground

Jumper screws should be installed at “PE-A”

(MOV/Input Filter Cap) and “PE-B” (CM Cap).

See page 3 for recommended torque.

Non-Solid Ground

Remove both jumper screws.

DPE-A Installed

PE-B Not Installed PE-A Installed

PE-B Installed Solid Ground

Jumper screws should be installed at “PE-A”

(MOV/Input Filter Cap) and “PE-B” (CM Cap).

See page 3 for recommended torque.

Non-Solid Ground

Remove both jumper screws.

DPE-A Installed

PE-B Not Installed PE-A Installed

PE-B Installed Solid Ground

Jumper screws should be installed at “PE-A”

(MOV/Input Filter Cap) and “PE-B” (CM Cap).

See page 3 for recommended torque.

Non-Solid Ground

Remove both jumper screws.

DPE-A Installed

PE-B Not Installed PE-A Installed

PE-B Installed Solid Ground

Jumper screws should be installed at “PE-A”

(MOV/Input Filter Cap) and “PE-B” (CM Cap).

See page 3 for recommended torque.

Non-Solid Ground

Remove both jumper screws.

PE-B

PE-A

PE-B

PE-A

PE-B

PE-A

PE-B

PE-A

Rockwell Automation Publication 750-IN011B-EN-P - July 2010

PowerFlex 750-Series Power Jumpers 5

DPE-A jumper wire

connected to

ground.

PE-B jumper wire

insulated/

disconnected from

ground.

PE-A jumper wire

and PE-B jumper

wire connected to

ground.

Solid Ground

MOV/Input Filter Cap jumper wire (PE-A) and

CM Cap jumper wire (PE-B) should be

connected to ground.

See page 3 for recommended torque.

Non-Solid Ground

MOV/Input Filter Cap jumper wire (PE-A) and

CM Cap jumper wire (PE-B) should be insulated

from ground.

DPE-A jumper wire

connected to

ground.

PE-B jumper wire

insulated/

disconnected from

ground.

PE-A jumper wire

and PE-B jumper

wire connected to

ground.

Solid Ground

MOV/Input Filter Cap jumper wire (PE-A) and

CM Cap jumper wire (PE-B) should be

connected to ground.

See page 3 for recommended torque.

Non-Solid Ground

MOV/Input Filter Cap jumper wire (PE-A) and

CM Cap jumper wire (PE-B) should be insulated

from ground.

Frame

Voltage

Code

Factory Default Jumper Settings

Power Source TypeCatalog Code “A” Catalog Code “J”

DC+

PE-B

PE-A

Insulated Connected

Insulated

Connected

PE-B

PE-A

Insulated Connected

Insulated

Connected

6PowerFlex 750-Series Power Jumpers

DPE-A1 & PE-A2

connected to

ground.

PE-B jumper plug

insulated/

disconnected from

ground.

PE-A1, PE-A2 and

PE-B connected to

ground.

Solid Ground

MOV jumper wire (PE-A1), Input Filter Cap

jumper plug (PE-A2) and the CM Cap jumper

plug (PE-B) should be connected to ground.

See page 3 for recommended torque.

Non-Solid Ground

MOV jumper wire (PE-A1), Input Filter Cap jumper

plug (PE-A2) and the CM Cap jumper plug (PE-B)

should be insulated/disconnected from ground.

Frame

Voltage

Code

Factory Default Jumper Settings

Power Source TypeCatalog Code “A” Catalog Code “J”

PE-A1

PE-A2

Insulated (P2)

Connected (P3)

Insulated

Connected

Insulated (J4)

Connected (J3)

www.rockwellautomation.com

Amer

cas:

Rockwell

Automation, 1201 South

Second

Street,

Milwaukee,

WI 53204

2496

USA,

Tel:

(1)

414.382.2000, Fax: (1)

414.382.4444

Europe

Middle East

Africa:

Rockwell

Automati

on,

Pegasus

Park,

De Kleetlaan 12a,

1831 Diegem, Belgium,

Tel: (32) 2 663

0600, Fax: (32) 2 663

0640

Asia Pacific: Rockwell Automation, Level 14,

Core F,

Cyberport

3, 100

Cyberport Road,

Hong Kong,

Tel: (852) 2887 4788, Fax:

(852) 2508

1846

Power,

Control

and

Information Solutions

Headquarters

Publication 750-IN011B-EN-P – July 2010 PN-81169

U.S. Allen-Bradley DrivesTechnical Support - Tel: (1) 262.512.8176, Fax: (1) 262.512.2222, E-mail: support@drives.ra.rockwell.com,

Online: www.ab.com/support/abdrives*PN-81169*

PN-81169

Andere Handbücher für PowerFlex 750 Series

Inhaltsverzeichnis

Andere Allen-Bradley Controller Handbücher

Allen-Bradley

Allen-Bradley PowerFlex 755 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 527 Bedienungsanleitung

Allen-Bradley

Allen-Bradley powerflex 700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet PLC-5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PLC-3 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley Studio 5000 Logix Emulate Betriebsanleitung

Allen-Bradley

Allen-Bradley PowerFlex Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 GuardLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1747-L20 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet PLC-5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 700S Bedienungsanleitung

Allen-Bradley

Allen-Bradley 22C-B012N103 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1391B Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley Pico 1760-L12AWA Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-OC Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix System 1756-L1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Studio 5000 Logix Emulate Bedienungsanleitung

Allen-Bradley

Allen-Bradley CENTERLINE 2100 Gebrauchsanweisung

Allen-Bradley

Allen-Bradley PowerFlex 755T Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1400 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley DriveLogix 5730 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung