Allen-Bradley 1771-IGD Bedienungsanleitung

Installation Data

TTL Input Module

Cat. No. 1771IGD

Installation Instructions

This document provides information on:

important pre-installation considerations

power supply requirements

initial handling

installing the module

using the indicators for troubleshooting

replacing the fuse

module specifications

You can use this module in a Series A or B 1771-A1B, -A2B, -A3B,

-A3B1, and -A4B chassis. The module is also compatible in a 1771-AM1

or -AM2 I/O chassis.

You can use any TTL device that meets the output logic level specification

of -0.2V dc to +0.8V dc (low), and 2.0V dc to 5.25V dc (high).

This module contains input filtering to limit the effects of voltage

transients caused by contact bounce and/or radiated electrical noise.

The delay due to filtering is less than 1ms.

For maximum noise immunity, the output of the TTL device should have a

pull-up resistor of 1k ohm (typical). Add an external pull-up resistor to the

output terminals of the device, if necessary. If you add a pull-up resistor, be

sure the TTL device maintains the low state requirement of -0.2V dc to

+0.8V dc with the increased load.

The TTL module requires power from two sources: the I/O chassis

backplane, and a +5V dc power supply that you provide for transmission of

TTL signals.

To The Installer

Preinstallation

Considerations

Power Requirements

TTL Input Module

Cat. No. 1771IGD

Installation Instructions

Backplane

The TTL module receives its power through the 1771 I/O chassis

backplane from the chassis power supply. The module requires 130mA

from the output of this supply. Add this to the requirements of all other

modules in the I/O chassis to prevent overloading the chassis backplane

and/or backplane power supply.

Customer Supply

You must provide a separate +5(+0.25)V dc power supply for the TTL

inputs of the module and for your TTL output devices. Your module

requires 380mA from the output of your supply. Ripple should not exceed

50mV peak to peak.

The TTL input module is shipped in a static-shielded bag to guard against

electrostatic discharge damage. Observe the following precautions when

handling the module.

Electrostatic Discharge Damage

ATTENTION: Under some conditions, electrostatic discharge

can degrade performance or damage the module. Observe the

following precautions to guard against electrostatic damage.

Wear an approved wrist strap grounding device, or touch a grounded

object to discharge yourself before handling the module.

Do not touch the backplane connector or connector pins.

If you configure or replace internal components, do not touch other

circuit components inside the module. If available, use a static-free

work station.

When not in use, keep the module in its static-shielded bag.

In this section, we tell you how to set the logic level jumper, key your I/O

chassis, install your module and make your wiring connections.

Selecting the Logic Level

Your module is preset to the positive-logic level. Use the following table to

choose between the two logic levels:

If you choose: Then: Jumper Position

HIGH = TRUE logic (positive) 2.0 to 5.25V dc corresponds to logic ``1" (on) Toward rear of module

LOW = TRUE logic (negative) -0.2 to 0.8V dc corresponds to logic ``1" (on) Toward front of module

Note: Selecting positive logic automatically enables the HIGH (positive logic) indicator.

Initial Handling

Installing Your Module

TTL Input Module

Cat. No. 1771IGD

Installation Instructions

You select high-true or low-true using the jumper accessible through a slot

at the top of the module.

1. Locate the jumper in the slot at the top edge of the module.

2. Use tweezers to position the jumper as required for your application.

When on front 2 pins, negative logic

selected (low = true).

TTL Input Module

When on rear 2 pins, positive logic

selected (high = true).

10449I

TTL Logic Level Selection Jumper Assembly

Keying Your I/O Chassis

Use the plastic keying bands, shipped with each I/O chassis, to key the I/O

slots to accept only this type of module.

The module circuit board is slotted in two places on the rear edge. The

position of the keying bands on the backplane connector must correspond

to these slots to allow insertion of the module. You can key any connector

in an I/O chassis to receive this module except for the left-most connector

reserved for adapter or processor modules. Place keying bands between the

following numbers labeled on the upper backplane connector:

Between 16 and 18

Between 24 and 26

You can change the position of these keys if system redesign and rewiring

makes insertion of a different module necessary.

Installing the Input Module

To install the TTL input module in your 1771 I/O chassis, follow the steps

listed below.

TTL Input Module

Cat. No. 1771IGD

Installation Instructions

ATTENTION: Remove power from the 1771 I/O chassis

backplane and wiring arm before removing or installing an

I/O module.

Failure to remove power from the backplane or field wiring

arm could cause module damage, degradation of

performance,

or injury.

Failure to remove power from the backplane could cause

injury or equipment damage due to possible unexpected

operation.

1. Turn off power to the I/O chassis.

2. Place the module in the plastic tracks on the top and bottom of the

slot that guides the module into position.

3. Do not force the module into its backplane connector. Apply firm,

even pressure on the module to seat it properly.

4. Secure the module’s position by doing the following:

with a Series A chassis, snap the chassis latch over the top of the

module

with a Series B chassis, pull down the locking bar

5. Connect the field wiring arm to the input module.

Connecting Wiring to the Input Module

Connect wiring to the input module using the field wiring arm (cat. no.

1771-WH) shipped with the module (shown in the connection diagram

below). Make your connections as follows:

1. Attach the field wiring arm to the pivot bar on the bottom of the I/O chassis.

2. Pivot the wiring arm upward and push it into the module until the wiring

arm clicks into position. The field wiring arm is designed to let you install

and remove the module without disconnecting the wires.

ATTENTION: Do not apply ac or reverse dc voltage to

module terminals. Circuitry at the input of module may

be damaged.

TTL Input Module

Cat. No. 1771IGD

Installation Instructions

3. Separate the shielded cables from wiring that radiates electrical noise.

Refer to category 2, low power dc I/O lines, in publication 1770-4.1,

‘‘Programmable Controller Wiring and Grounding Guidelines”.

4. Prepare the cable for grounding by doing the following:

Remove a length of cable

jacket from the Belden 8761

cable.

Pull the foil shield and bare

drain wire from the insulated

wires.

Bare

drain

wire

Insulated

wires

Foil

shield

Twist the foil shield and drain

wire together to form a single

strand.

Attach a ground lug.

20104

Belden

8761 Cable

5. Ground the single strand (at the ground lug end) to the grounding

stud on the I/O chassis or by using single-point grounding.

19480

When you connect grounding conductors to the I/O chassis

grounding stud, place a star washer under the first lug, then

place a nut with captive lock washer on top of each ground lug.

Grounding Stud

1Use

the cup washer if crimpon lugs are not used.

Chassis Ground Singlepoint Grounding

Ground Lug

Nut

Ground Lug1

Star

Washer

I/O Chassis Side Plate

Nut and Captive

Washer

Externaltooth Washers

#10 Threadforming screw

19923

TTL Input Module

Cat. No. 1771IGD

Installation Instructions

6. You must connect both ends of the insulated signal return wire in

each transmission cable as follows:

connect one end to the dc common terminal of your +5V dc power

supply

connect the other end to the dc common terminal of the field

wiring arm

dc common

+5V dc

Input 00

Input 01

Input 02

Input 03

Input 04

Input 05

Input 06

Input 07

Customer

Power Supply

+5V dc

Ground cable shield at the chassis

grounding stud or by using single

point grounding

TTL Devices must have opencollector outputs.

Internal or external pullup resistor (1K ohm typical).

(See applicable codes and laws.)

Input 10

Input 11

Input 12

Input 13

Input 14

Input 15

Input 16

Input 17

+5V dc

(Actual wiring runs in this direction.)

10450I

1You can make this connection to terminal A, B, C or D.

Field Wiring Arm

Cat. No. 1771WH

7. Connect TTL output devices using Belden 8761 shielded cable as

shown in the connection diagram. Do not exceed 50 cable feet for any

output device. Connect the insulated wires to their respective

terminals on the field wiring arm.

Driving Inputs with Outputs

Input terminals of the TTL input module (cat. no. 1771-IGD) may be

directly driven by the outputs of a TTL output module (cat. no.

1771-OGD). Connect the cable shield between modules at one end only.

TTL Input Module

Cat. No. 1771IGD

Installation Instructions

The front panel of your module contains 18 status indicators (Figure 1).

The green top indicator is labeled ‘‘ACTIVE.” This indicator is on when

the fuse is good. The green bottom indicator, when on, indicates you

selected high-true logic. When off, it indicates you selected low-true logic.

Each of the 16 red status indicators light when their corresponding input

terminal senses TTL voltages in the true state.

Figure 1

Status

Indicators

ACTIVE

Module Active Indicator (green)

00 to 17 Status Indicators (red)

HIGH

Positive Logic Indicator (green)

10451I

To replace a blown fuse, proceed as follows:

ATTENTION: Remove power from the 1771 I/O chassis

backplane and field wiring arm before removing or installing an

I/O module.

Failure to remove power from the backplane or field wiring

arm could cause module damage, degradation of

performance, or injury.

Failure to remove power from the backplane could cause

injury or equipment damage due to possible unexpected

operation.

1. Turn off power to the chassis.

2. Remove the module from the I/O chassis.

3. Remove the blown fuse from the fuse holder (accessible through the

slot in the side cover), and replace with a 0.5A, 250V normal

blow fuse.

4. Reinsert module into the I/O chassis.

5. Turn on power to the chassis.

Interpreting the Status

Indicators

Replacing the Fuse

Specifications

TTL Input Module

Cat. No. 1771IGD

Installation Instructions

Inputs per Module 16

Module Location Series A or B 1771A1B, A2B, A3B,

A3B1, or A4B I/O chassis. Other locations

include 1771AM1, and AM2 I/O chassis.

Input Voltage Rating

HIGH = TRUE

LOW = TRUE

ON: 2.0 to 5.25V dc

OFF: -0.2 to +0.8V dc

ON: -0.2 to +0.8V dc

OFF: 2.0 to 5.25V dc

Customer Supply Voltage 5.0V dc (+0.25V)

50mV peaktopeak ripple max.

Customer Current Sink Requirements 7mA maximum (source per input)

0.8mA maximum (sink per input)

Customer Supply Current per Module 380mA max.

Input Signal Delay Less than 1ms

Power Dissipation 2.7 Watts (max.); 0.4 Watts (min.)

Thermal Dissipation 9.2 BTU/hr (max.); 1.4 BTU/hr (min.)

Backplane Current 130mA max.

Isolation Voltage Tested at 1500V ac (rms) for 1 second

Environmental Conditions

Operational Temperature

Storage Temperature

Relative Humidity

0oto 60oC (32oto 140oF)

-40oto 85oC (-40oto 185oF)

5 to 95% (without condensation)

Fuse 0.5A 250V normal blow

Conductors Wire Size

Cable

Category

14 gauge stranded maximum

3/64 inch insulation maximum

Shielded (Belden 8761)

Keying Between 16 and 18

Between 24 and 26

Field Wiring Arm Catalog Number 1771WH

Wiring Arm Screw Torque 79 inchpounds

1Refer

to publication 17704.1, Programmable Controller Wiring and Grounding Guidelines.

With major offices worldwide.

Algeria •

Argentina

•

Australia

•

Austria

•

Bahrain

•Belgium •Brazil •

Bulgaria

•

Canada

•Chile •

China, PRC

•

Colombia

•Costa Rica •

Croatia

•

Cyprus

•Czech

Republic

•

Denmark

•

Ecuador

•Egypt •El Salvador •Finland •France •

Germany

•

Greece

•

Guatemala

•

Honduras

•

Hong Kong

•

Hungary

•Iceland •

India

•

Indonesia

•

Israel

•Italy •Jamaica •

Japan

•

Jordan

•

Korea

•

Kuwait

•

Lebanon

•Malaysia •Mexico •

New Zealand

•

Norway

•Oman •Pakistan •

Peru

•Philippines

•

Poland

•

Portugal

•

Puerto Rico

•

Qatar

•

Romania

•

Russia-CIS

•

Saudi Arabia

•

Singapore

•Slovakia •Slovenia •

South Africa, Republic

•Spain •

Switzerland

•

aiwan

•Thailand •

The Netherlands

•T

urkey

•

United Arab Emirates

•

United Kingdom

•

United States

•

Uruguay

•V

enezuela

•Yugoslavia

orld Headquarters, AllenBradley

, 1201 South Second Street, Milwaukee, WI 53204 USA, T

el: (1) 414 3822000 Fax: (1) 414 3824444

AllenBradley has been helping its customers improve productivity and quality for 90 years.

AB designs, manufactures and supports a broad range of control and automation products

worldwide. They include logic processors, power and motion control devices, manmachine

interfaces and sensors. AllenBradley is a subsidiary of Rockwell International, one of the

world's leading technology companies.

Publication

17712.178 January 1994

Supersedes

Publication 17712.131 - May 1989

95510768

1994 AllenBradley Company

, Inc. Printed in USA

Inhaltsverzeichnis

Andere Allen-Bradley E/A-System Handbücher

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746-INT4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-IE2C Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2097-TB1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-HSC Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IC16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-IB16K Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IF2OF2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IG16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NR4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1738-IR2M12 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock-LP 1792-IB16LP Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1775-S4A Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IB16D Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746-NIO4I Bedienungsanleitung

Allen-Bradley

Allen-Bradley Rockwell Automation 1734-AENT Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-OB8EP Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NI4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-ASB Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 ControlLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-IB Installations- und Benutzerhandbuch

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IJ2 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung