Allen-Bradley FLEX I/O 1794-IC16 Bedienungsanleitung

Installation Instructions

FLEX I/O 48V DC Digital Input and

Output Modules

Catalog numbers 1794-IC16, 1794-OC16

Table of Contents

Topic Page

Important User Information 2

Environment and Enclosure 3

Preventing Electrostatic Discharge 3

European Hazardous Location Approval 5

North American Hazardous Location Approval 7

Install Your 48V DC Digital Input or Output Module 8

Connect Wiring for the 1794-IC16 or 1794-OC16 9

Configure Your 48V DC Output Module, 1794-OC16 14

Specifications 14

2FLEX I/O 48V DC Digital Input and Output Modules

Publication 1794-IN105C-EN-P - July 2018

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation Sales Office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between solid

state equipment and hard-wired electromechanical devices. Because of this difference, and also because

of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc. is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you

identify a hazard, avoid a hazard, or recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

FLEX I/O 48V DC Digital Input and Output Modules 3

Publication 1794-IN105C-EN-P - July 2018

Environment and Enclosure

Preventing Electrostatic Discharge

ATTENTION: This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications (as defined in

EN/IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is not intended for use in residential environments and may not

provide adequate protection to radio communication services in such

environments.

This equipment is supplied as open-type equipment for indoor use. It must be

mounted within an enclosure that is suitably designed for those specific

environmental conditions that will be present and appropriately designed to

prevent personal injury resulting from accessibility to live parts. The enclosure

must have suitable flame-retardant properties to prevent or minimize the spread

of flame, complying with a flame spread rating of 5VA or be approved for the

application if nonmetallic. The interior of the enclosure must be accessible only

by the use of a tool. Subsequent sections of this publication may contain more

information regarding specific enclosure type ratings that are required to

comply with certain product safety certifications.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines, Rockwell

Automation publication 1770-4.1, for more installation requirements.

• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of

the degrees of protection provided by enclosures.

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

4FLEX I/O 48V DC Digital Input and Output Modules

Publication 1794-IN105C-EN-P - July 2018

ATTENTION: This product is grounded through the DIN rail to chassis ground.

Use zinc plated chromate-passivated steel DIN rail to assure proper grounding.

The use of other DIN rail materials (for example, aluminum or plastic) that can

corrode, oxidize, or are poor conductors, can result in improper or intermittent

grounding. Secure DIN rail to mounting surface approximately every 200 mm

(7.8 in.) and use end-anchors appropriately. Be sure to ground the DIN rail

properly.

ATTENTION: Refer to Industrial Automation Wiring and Grounding

Guidelines, Rockwell Automation publication 1770-4.1, for more information.

ATTENTION: If this equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be impaired.

ATTENTION: If this equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be impaired.

ATTENTION: Read this document and the documents listed in the Additional

Resources section about installation, configuration, and operation of this

equipment before you install, configure, operate, or maintain this product.

Users are required to familiarize themselves with installation and wiring

instructions in addition to requirements of all applicable codes, laws, and

standards.

ATTENTION: Installation, adjustments, putting into service, use, assembly,

disassembly, and maintenance are required to be carried out by suitably trained

personnel in accordance with applicable code of practice.

In case of malfunction or damage, no attempts at repair should be made. The

module should be returned to the manufacturer for repair. Do not dismantle the

module.

ATTENTION: Use only a soft dry anti-static cloth to wipe down equipment. Do

not use any cleaning agents.

FLEX I/O 48V DC Digital Input and Output Modules 5

Publication 1794-IN105C-EN-P - July 2018

European Hazardous Location Approval

The following modules are European Zone 2 approved: 1794-IC16, 1794-OC16.

WARNING: When you insert or remove the module while backplane power is

on, an electric arc can occur. This could cause an explosion in hazardous

location installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

Repeated electric arcing causes excessive wear to contacts on both the module

and its mating connector. Worn contacts may create electrical resistance that

can affect module operation.

The following applies to products marked II 3 G:

Are Equipment Group II, Equipment Category 3, and comply with the Essential Health and

Safety Requirements relating to the design and construction of such equipment given in

Annex II to EU Directive 2014/34/EU. See the EU Declaration of Conformity at

http://www.rockwellautomation.com/global/certification/overview.page for details.

The type of protection is II 3G Ex nA IIC T3 Gc according to EN 60079-15.

Comply to Standards EN 60079-0:2012, EN 60079-15:2010, reference certificate number

LCIE 01 ATEX 6020 X.

Are intended for use in areas in which explosive atmospheres caused by gases, vapors,

mists, or air are unlikely to occur, or are likely to occur only infrequently and for short

periods. Such locations correspond to Zone 2 classification according to ATEX directive

2014/34/EU.

6FLEX I/O 48V DC Digital Input and Output Modules

Publication 1794-IN105C-EN-P - July 2018

WARNING: Observe the following additional certification requirements:

• This equipment is not resistant to sunlight or other sources of

UV radiation.

• This equipment shall be mounted in an ATEX/IECEx Zone 2 certified

enclosure with a minimum ingress protection rating of at least IP54 (in

accordance with EN/IEC 60079-15) and used in an environment of not

more than Pollution Degree 2 (as defined in EN/IEC 60664-1) when

applied in Zone 2 environments. The enclosure must be accessible only by

the use of a tool.

• This equipment shall be used within its specified ratings defined by

Rockwell Automation.

• The instructions in the user manual shall be observed.

• This equipment must be used only with ATEX certified Rockwell

Automation backplanes.

• Earthing is accomplished through mounting of modules on rail.

• Devices shall be used in an environment of not more than Pollution

Degree 2.

• Enclosure must be marked with the following: "Warning - Do not open

when energized." After installation of equipment into the enclosure,

access to termination compartments shall be dimensioned so that

conductors can be readily connected.

FLEX I/O 48V DC Digital Input and Output Modules 7

Publication 1794-IN105C-EN-P - July 2018

North American Hazardous Location Approval

The 1794-IC16, 1794-OC16 module is Hazardous Location approved:

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l’utilisation de cet équipement

en environnements dangereux:

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable

for use in Class I Division 2 Groups A, B, C, D, Hazardous

Locations and nonhazardous locations only. Each product

is supplied with markings on the rating nameplate

indicating the hazardous location temperature code.

When combining products within a system, the most

adverse temperature code (lowest "T" number) may be

used to help determine the overall temperature code of

the system. Combinations of equipment in your system

are subject to investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent

qu'à une utilisation en environnements de Classe I Division 2

Groupes A, B, C, D dangereux et non dangereux. Chaque produit

est livré avec des marquages sur sa plaque d'identification qui

indiquent le code de température pour les environnements

dangereux. Lorsque plusieurs produits sont combinés dans un

système, le code de température le plus défavorable (code de

température le plus faible) peut être utilisé pour déterminer le

code de température global du système. Les combinaisons

d'équipements dans le système sont sujettes à inspection par

les autorités locales qualifiées au moment de l'installation.

WARNING:

EXPLOSION HAZARD

• Do not disconnect equipment unless

power has been removed or the area is

known to be nonhazardous.

• Do not disconnect connections to this

equipment unless power has been

removed or the area is known to be

nonhazardous. Secure any external

connections that mate to this

equipment by using screws, sliding

latches, threaded connectors, or other

means provided with this product.

• Substitution of components may impair

suitability for Class I, Division 2.

WARNING:

RISQUE D’EXPLOSION

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher l'équipement.

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher les connecteurs. Fixer

tous les connecteurs externes reliés à cet

équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou autres

moyens fournis avec ce produit.

• LLa substitution de composants peut rendre

cet équipement inadapté à une utilisation en

environnement de Classe I, Division 2.

8FLEX I/O 48V DC Digital Input and Output Modules

Publication 1794-IN105C-EN-P - July 2018

Install Your 48V DC Digital Input or Output Module

The module mounts on a 1794 terminal base.

1. Rotate the keyswitch (3) on the terminal base (4) clockwise to position 4 as

required for this type of module.

2. Make sure the FlexBus connector (1) is pushed all the way to the left to connect

with the neighboring terminal base/adapter.

You cannot install the module unless the connector is fully extended.

3. Make sure the pins on the bottom of the module are straight so they will align

properly with the connector in the terminal base.

4. Position the module (7) with its alignment bar (6) aligned with the groove (5) on

the terminal base.

5. Press firmly and evenly to seat the module in the terminal base unit. The module

is seated when the latching mechanism (2) is locked into the module.

Description Description

1 FlexBus connectors 5 Groove

2 Latching mechanism 6 Alignment bar

3 Keyswitch 7 Module

4 Terminal base

45284

FLEX I/O 48V DC Digital Input and Output Modules 9

Publication 1794-IN105C-EN-P - July 2018

Connect Wiring for the 1794-IC16 or 1794-OC16

1. Connect individual input (1794-IC16) or output (1794-OC16) wiring to

numbered terminals on the 0…15 row (A) as indicated in the Wiring

Connections for 1794-IC16 and 1794-OC16 table.

2. 1794-IC16 – Connect the associated +V DC power lead of the input device to

the corresponding terminal on the 34…51 row (C) for each input as indicated in

the Wiring Connections for 1794-IC16 and 1794-OC16 table. The +V DC

power terminals of row (C) are internally connected together.

3. 1794-OC16 – Connect the associated V DC common lead of the output device

to the corresponding terminal on the 16…33 row (B) for each output as indicated

in the Wiring Connections for 1794-IC16 and 1794-OC16 table. The V DC

common terminals of row (B) are internally connected together.

4. 1794-IC16 only – Connect the associated input common (3-wire devices only)

to the corresponding terminal on the 16…33 row (B) for each input as indicated

in the Wiring Connections for 1794-IC16 and 1794-OC16 table. Commons are

internally connected together.

5. Connect +V DC power to terminal 34 on the 34…51 row (C).

6. Connect V DC common to terminal 16 on the 16…33 row (B).

7. If daisychaining power to the next terminal base, connect a jumper from terminal

51 (+V DC) on this base unit to terminal 34 on the next base unit.

8. If continuing V DC common to the next base unit, connect a jumper from

terminal 33 (common) on this base unit to terminal 16 on the next base unit.

Wiring Connections for 1794-IC16 and 1794-OC16

1794-IC16 1794-OC16

1794-TB3, 1794-TB3S 1794-TB2, 1794-TB3,

1794-TB3S

Input Input

Terminal

48V DC

Supply

Common(1) Output Output

Terminal

Common

Input 0 A-0 C-35 B-17 Output 0 A-0 B-17

Input 1 A-1 C-36 B-18 Output 1 A-1 B-18

Input 2 A-2 C-37 B-19 Output 2 A-2 B-19

Input 3 A-3 C-38 B-20 Output 3 A-3 B-20

10 FLEX I/O 48V DC Digital Input and Output Modules

Publication 1794-IN105C-EN-P - July 2018

Input 4 A-4 C-39 B-21 Output 4 A-4 B-21

Input 5 A-5 C-40 B-22 Output 5 A-5 B-22

Input 6 A-6 C-41 B-23 Output 6 A-6 B-23

Input 7 A-7 C-42 B-24 Output 7 A-7 B-24

Input 8 A-8 C-43 B-25 Output 8 A-8 B-25

Input 9 A-9 C-44 B-26 Output 9 A-9 B-26

Input 10 A-10 C-45 B-27 Output 10 A-10 B-27

Input 11 A-11 C-46 B-28 Output 11 A-11 B-28

Input 12 A-12 C-47 B-29 Output 12 A-12 B-29

Input 13 A-13 C-48 B-30 Output 13 A-13 B-30

Input 14 A-14 C-49 B-31 Output 14 A-14 B-31

Input 15 A-15 C-50 B-32 Output 15 A-15 B-32

A = Input/Output terminals

B = Common terminals

C = Power terminals (C-34 to C-51 on 1794-TB3 and 1794-TB3S; C-34 and C-51 on 1794-TB2)

(1) 3-wire devices use input, supply and common. 2-wire devices use input and supply.

Wiring Connections for 1794-IC16 and 1794-OC16

1794-IC16 1794-OC16

1794-TB3, 1794-TB3S 1794-TB2, 1794-TB3,

1794-TB3S

Input Input

Terminal

48V DC

Supply

Common(1) Output Output

Terminal

Common

Andere Handbücher für FLEX I/O 1794-IC16

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley E/A-System Handbücher

Allen-Bradley

Allen-Bradley FLEX 1794-IF2XOF2I Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2097-TB1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 RTD/Resistance Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock MaXum 4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IF2OF2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1791-0A32 B Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IH16ISOE Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IQ32T Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IF4I Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX XT I/O 1794-IF4IXT Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IM8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-IB16K Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1738-IR2M12 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IG16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1762-IQ8OW6 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NR4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-OF8IH Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-IB8S Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2071-TBIO Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NI4 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung