Allen-Bradley ControlLogix 1756-IH16ISOE Bedienungsanleitung

Publication 1756-IN592A-EN-P - March 2004

Installation Instructions

ControlLogix 90-140V DC Sequence of Events

Input Module

Catalog Number 1756-IH16ISOE

Obtain a User Manual

This product also has a user manual (pub. no. 1756-UM528). To view

it, visit www.ab.com/manuals or www.theautomationbookstore.com.

To purchase a manual, you can:

•contact your distributor or Rockwell Automation representative

•visit www.theautomationbookstore.com and place an order

•call 800.963.9548 (USA/Canada) or 001.320.725.1574 (outside

USA/Canada)

To: See page:

Identify the Module Components 6

Note the Power Requirements 6

Install the Module 7

Key the Module and Removable Terminal Block/Interface Module 8

Wire the Removable Terminal Block 9

Wire the 1756-IH16ISOE Module 10

Assemble the Removable Terminal Block and the Housing 11

Install the Removable Terminal Block onto the Module 11

Check the Indicators 12

Remove the Removable Terminal Block from the Module 13

Remove the Module 13

See Specifications 14

AB Drives

2ControlLogix 90-140V DC Sequence of Events Input Module

Publication 1756-IN592A-EN-P - March 2004

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.ab.com/manuals/gi) describes some important differences between solid state equipment

and hard-wired electromechanical devices. Because of this difference, and also because of the wide

variety of uses for solid state equipment, all persons responsible for applying this equipment must

satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc. is prohibited.

Throughout this manual we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an explosion in a

hazardous environment, which may lead to personal injury or death, property damage,

or economic loss.

IMPORTAN

Identifies information that is critical for successful application and understanding of the

product.

ATTENTION Identifies information about practices or circumstances that can lead to personal injury

or death, property damage, or economic loss. Attentions help you:

•identify a hazard

•avoid a hazard

•recognize the consequence

SHOCK HAZAR

Labels may be located on or inside the drive to alert people that dangerous voltage may

be present.

BURN HAZARD Labels may be located on or inside the drive to alert people that surfaces may be

dangerous temperatures.

ControlLogix 90-140V DC Sequence of Events Input Module 3

Publication 1756-IN592A-EN-P - March 2004

Environment and Enclosure

Prevent Electrostatic Discharge

ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial environment, in

overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes

up to 2000 meters without derating.

This equipment is considered Group 1, Class A industrial equipment according to

IEC/CISPR Publication 11. Without appropriate precautions, there may be potential

difficulties ensuring electromagnetic compatibility in other environments due to

conducted as well as radiated disturbance.

This equipment is supplied as "open type" equipment. It must be mounted within an

enclosure that is suitably designed for those specific environmental conditions that will

be present and appropriately designed to prevent personal injury resulting from

accessibility to live parts. The interior of the enclosure must be accessible only by the

use of a tool. Subsequent sections of this publication may contain additional

information regarding specific enclosure type ratings that are required to comply with

certain product safety certifications.

NOTE: See NEMA Standards publication 250 and IEC publication 60529, as applicable,

for explanations of the degrees of protection provided by different types of enclosure.

Also, see the appropriate sections in this publication, as well as the Allen-Bradley

publication 1770-4.1 ("Industrial Automation Wiring and Grounding Guidelines"), for

additional installation requirements pertaining to this equipment.

ATTENTION This equipment is sensitive to electrostatic discharge, which can cause internal

damage and affect normal operation. Follow these guidelines when you handle this

equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•If available, use a static-safe workstation.

•When not in use, store the equipment in appropriate static-safe packaging.

AB Drives

4ControlLogix 90-140V DC Sequence of Events Input Module

Publication 1756-IN592A-EN-P - March 2004

Removal and Insertion Under Power

Be sure that power is removed or the area is nonhazardous before

proceeding. Repeated electrical arcing causes excessive wear to

contacts on both the module and its mating connector. Worn contacts

may create electrical resistance that can affect module operation.

North American Hazardous Location Approval

WARNING When you insert or remove the module while backplane

power is on, an electrical arc can occur. This could cause

an explosion in hazardous location installations.

The following information applies

when operating this equipment in

hazardous locations:

Informations sur l’utilisation de cet

équipement en environnements

dangereux:

Products marked “CL I, DIV 2, GP A, B, C,

D” are suitable for use in Class I Division 2

Groups A, B, C, D, Hazardous Locations

and nonhazardous locations only. Each

product is supplied with markings on the

rating nameplate indicating the hazardous

location temperature code. When

combining products within a system, the

most adverse temperature code (lowest

“T” number) may be used to help

determine the overall temperature code of

the system. Combinations of equipment in

your system are subject to investigation

by the local Authority Having Jurisdiction

at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D"

ne conviennent qu’à une utilisation en

environnements de Classe I Division 2 Groupes

A, B, C, D dangereux et non dangereux. Chaque

produit est livré avec des marquages sur sa

plaque d’identification qui indiquent le code de

température pour les environnements

dangereux. Lorsque plusieurs produits sont

combinés dans un système, le code de

température le plus défavorable (code de

température le plus faible) peut être utilisé pour

déterminer le code de température global du

système. Les combinaisons d’équipements

dans le système sont sujettes à inspection par

les autorités locales qualifiées au moment de

l’installation.

ControlLogix 90-140V DC Sequence of Events Input Module 5

Publication 1756-IN592A-EN-P - March 2004

WARNING EXPLOSION HAZARD

•Do not disconnect

equipment unless

power has been

removed or the area

is known to be

nonhazardous.

•Do not disconnect

connections to this

equipment unless

power has been

removed or the area

is known to be

nonhazardous.

Secure any external

connections that

mate to this

equipment by using

screws, sliding

latches, threaded

connectors, or other

means provided

with this product.

•Substitution of

components may

impair suitability for

Class I, Division 2.

•If this product

contains batteries,

they must only be

changed in an area

known to be

nonhazardous.

AVERTISSEMENT RISQUE D’EXPLOSION

•Couper le courant ou

s’assurer que

l’environnement est

classé non dangereux

avant de débrancher

l'équipement.

•Couper le courant ou

s'assurer que

l’environnement est

classé non dangereux

avant de débrancher

les connecteurs. Fixer

tous les connecteurs

externes reliés à cet

équipement à l'aide

de vis, loquets

coulissants,

connecteurs filetés ou

autres moyens fournis

avec ce produit.

•La substitution de

composants peut

rendre cet équipement

inadapté à une

utilisation en

environnement de

Classe I, Division 2.

•S’assurer que

l’environnement est

classé non dangereux

avant de changer les

piles.

The following information applies

when operating this equipment in

hazardous locations:

Informations sur l’utilisation de cet

équipement en environnements

dangereux:

AB Drives

6ControlLogix 90-140V DC Sequence of Events Input Module

Publication 1756-IN592A-EN-P - March 2004

Identify the Module Components

You received the following components with your order:

•1756-IH16ISOE module

•Removable Terminal Block (RTB) door label

•jumper bar

If you did not receive these components, contact your local

distributor Rockwell Automation sales office.

This module mounts in a 1756 chassis and uses a separately-ordered

RTB or a Bulletin 1492 Interface Module (IFM)(1) to connect all

field-side wiring. This module uses one of the following RTBs:

•1756-TBCH 36 position Cage clamp RTB

•1756-TBS6H 36 position Spring clamp RTB

Use an extended-depth cover (1756-TBE) for applications with heavy

gauge wiring or requiring additional routing space. When using an

IFM, consult the documentation that came with it to connect wiring.

Note the Power Requirements

This module receives power from the 1756 chassis power supply and

requires 2 sources of power from the ControlLogix backplane:

•275mA at 5.1V dc

•2mA at 24V dc

Add this current/power value (1.3W) to the requirements of all other

modules in the chassis to prevent overloading the power supply.

(1) The ControlLogix system has been agency certified using only the ControlLogix RTBs (i.e. 1756-TBCH,

1756-TBNH 1756-TBSH and 1756-TBS6H). Any application that requires agency certification of the

ControlLogix system using other wiring termination methods may require application specific approval

by the certifying agency.

IMPORTANT Before you install your module, you should:

•install and ground a 1756 chassis and power supply.

•order and receive an RTB or IFM, and its

components, for your application.

ControlLogix 90-140V DC Sequence of Events Input Module 7

Publication 1756-IN592A-EN-P - March 2004

Install the Module

You can install or remove the module while chassis power is applied.

Be sure that power is removed or the area is nonhazardous before

proceeding. Repeated electrical arcing causes excessive wear to

contacts on both the module and its mating connector. Worn contacts

may create electrical resistance that can affect module operation.

1. Align the circuit board with the top and bottom chassis guides.

2. Slide the module into chassis until module locking tabs click.

WARNING When you insert or remove the module while backplane

power is on, an electrical arc can occur. This could cause

an explosion in hazardous location installations.

20861–M

Printed

Circuit

Board

Locking tab

AB Drives

8ControlLogix 90-140V DC Sequence of Events Input Module

Publication 1756-IN592A-EN-P - March 2004

Key the Module and Removable Terminal Block/Interface Module

Use the wedge-shaped keying tabs and U-shaped keying bands to

prevent connecting the wrong wires to your module.

Key positions on the module that correspond to unkeyed positions

on the RTB. For example, if you key the first position on the module,

leave the first position on the RTB unkeyed.

1. To key the module, insert the U-shaped band, as shown.

2. Push the band until it snaps in place.

3. To key the RTB or IFM, insert the wedge-shaped tab with

rounded edge first, as shown.

4. Push the tab until it stops.

Reposition the tabs to rekey future module applications.

20850–M

U-shaped

bands

20851–M

Wedge-shaped tab

ControlLogix 90-140V DC Sequence of Events Input Module 9

Publication 1756-IN592A-EN-P - March 2004

Wire the Removable Terminal Block

Wire the RTB with a 1/8 inch (3.2mm) maximum flat-bladed

screwdriver before installing it onto the module.

Be sure that power is removed or the area is nonhazardous before

proceeding.

WARNING When you connect or disconnect the Removable

Terminal Block (RTB) while field side power is on, an

electrical arc can occur. This could cause an explosion in

hazardous location installations.

Spring Clamp RTB Cage Clamp RTB

20860-M 20859-M

1. Strip 7/16 inch (11mm) maximum

length of wire.

2. Insert the screwdriver into the

inner hole of the RTB.

3. Insert the wire into the

open terminal and

remove the screwdriver.

1. Strip 3/8 inch (9.5mm) maximum

length of wire.

2. Insert the wire into the open terminal.

3. Turn the screw clockwise to close the

terminal on the wire.

AB Drives

10 ControlLogix 90-140V DC Sequence of Events Input Module

Publication 1756-IN592A-EN-P - March 2004

Wire the 1756-IH16ISOE Module

You can only connect wiring to your module with an RTB or IFM.

After completing field-side wiring, secure the wires in the strain relief

area with a cable-tie.

WARNING If you connect or disconnect wiring while the field-side power is

on, an electrical arc can occur. This could cause an explosion in

hazardous location installations. Be sure that power is removed

or the area is nonhazardous before proceeding.

40167-M

910

1112

1314

1516

1718

1920

2122

2324

2526

2728

2930

3132

3334

3536

Non-isolated

wiring

Isolated wiring

1. All terminals with the same name are connected together on the module. For

example, DC (-) can be connected to either terminal marked GND-15.

2. When you use the second GND-15 terminal to daisy chain to other RTBs, always

connect the daisy chain to the terminal directly connected to the supply wire, as

shown in the example above.

3. If separate power sources are used, do not exceed the specified isolation voltage.

4. Do not connect more than 2 wires to any single terminal.

5. The jumper bar is part number 97739201; use this number to order additional bars.

Daisy chain to other RTBs

DC (-)

Jumper bar

(Cut to length)

DC-6 (-) DC-6 (+)

DC (+)

DC-0 (+)

DC-1 (+)

DC-0 (-)

DC-5 (-)

IN-0

IN-1

IN-2

IN-3

IN-8

IN-4

IN-5

IN-6

IN-7

Not used

IN-9

IN-10

IN-11

IN-12

IN-13

IN-14

IN-15

Not used

GND-0

GND-1

GND-2

GND-3

GND-8

GND-4

GND-5

GND-6

GND-7

Not used

GND-9

GND-10

GND-11

GND-12

GND-13

GND-14

GND-15

NOTES:

DC-5 (+)

Sink input wiring

Source input wiringSource input wiring

Sink input wiring

Inhaltsverzeichnis

Andere Allen-Bradley E/A-System Handbücher

Allen-Bradley

Allen-Bradley FLEX XT I/O 1794-IF4IXT Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IG16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FlexLogix 1794 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746-IA4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX Ex 1797-OB4D Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-IF8I Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IV16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NR4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IQ32T Bedienungsanleitung

Allen-Bradley

Allen-Bradley Compact 5000 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1797-IBN16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2097-TB1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Flex I/O Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 ControlLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1775-S4A Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IB16D Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-IB16K Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-IQ32 Service-Handbuch

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IT8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1719 Ex I/O Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung