Allen-Bradley ControlLogix 1756-IV16 Bedienungsanleitung

Publication 1756-IN006A-EN-P - December 2000

Installation Instructions

ControlLogix

DC (10-30V) Sourcing Input Module

(Catalog Number 1756-IV16)

Obtain a User Manual

This product also has a user manual (pub. no. 1756-UM058C-EN-P).

To view it, visit www.ab.com/manuals or

www.theautomationbookstore.com You can also purchase a printed

manual by:

•contacting your local distributor or Rockwell Automation

representative

To: See page:

Obtain a User Manual 1

Identify the Module Components 2

Prevent Electrostatic Discharge 3

See Removal and Insertion Under Power (RIUP) 3

Understand Compliance to European Union Directive 4

Note the Power Requirements 5

Install the Module 5

Key the Removable Terminal Block/Interface Module 6

Wire the Module 7

Assemble the Removable Terminal Block and the Housing 8

Install the Removable Terminal Block onto the Module 8

Checkthe Indicators 10

Remove the Removable Terminal Block from the Module 11

Remove the Module 12

See 1756-IV16Specifications 12

Hazardous Location information 14

Allen-Bradley Motors

2ControlLogix DC (10-30V) Sourcing Input Module

Publication 1756-IN006A-EN-P - December 2000

•visiting www.theautomationbookstore.com and placing

an order

•calling 800.963.9548 (USA/Canada) or 001.320.725.1574

(outside USA/Canada)

Identify the Module Components

You received the following components with your order:

•1756-IV16 module

•Removable Terminal Block (RTB) door label

If you did not receive these components, contact your Rockwell

Automation sales office.

This module mounts in a ControlLogixchassis and uses a

separately-ordered RTB or a Bulletin 1492 Interface Module (IFM) to

connect all field-side wiring.

This module uses one of the following RTBs:

•1756-TBNH 20 position NEMA RTB

•1756-TBSH 20 position Spring Clamp RTB

Use an extended-depth cover (1756-TBE) for applications with heavy

gauge wiring or requiring additional routing space. When using an

IFM, consult the documentation that came with it to connect

all wiring.

IMPORTANT Before you install your module, you should

have already:

•installed and grounded a 1756 chassis and

power supply.

•ordered and received an RTB or IFM and its

components for your application.

ControlLogix DC (10-30V) Sourcing Input Module 3

Publication 1756-IN006A-EN-P - December 2000

Prevent Electrostatic Discharge

Removal and Insertion Under Power (RIUP)

ATTENTION

Electrostatic discharge can damage integrated circuits or

semiconductors if you touch backplane connector pins.

Follow these guidelines when you handle the module:

•Touch a grounded object to discharge

static potential.

•Wear an approved wrist-strap grounding device.

•Do not touch the backplane connector or connector

pins.

•Do not touch circuit components inside the module.

•If available, use a static-safe work station.

•When not in use, keep the module in its static-shield

box.

WARNING

This module is designed so you can remove and insert it

under backplane power and field-side power. When you

remove or insert a module while field-side power is

applied, you may cause an electrical arc. An electrical

arc can cause personal injury or property damage

because it may:

•send an erroneous signal to your system’s field

devices, causing unintended machine motion or loss

of process control.

•cause an explosion in a hazardous environment.

Repeated electrical arcing causes excessive wear to

contacts on both the module and its mating connector.

Worn contacts may create electrical resistance.

When you insert or remove the module while backplane

power is on, or you connect or disconnect the RTB with

field-side power applied, an electrical arc can occur. This

could cause an explosion in hazardous location

installations. Be sure that power is removed or the area is

non-hazardous before proceeding.

Allen-Bradley Motors

4ControlLogix DC (10-30V) Sourcing Input Module

Publication 1756-IN006A-EN-P - December 2000

Understand Compliance to European Union Directive

If this product bears the CE marking, it is approved for installation

within the European Union and EEA regions. It has been designed

and tested to meet the following directives.

EMC Directive

This product is tested to meet Council Directive 89/336/EEC

Electromagnetic Compatibility (EMC) and the following standards, in

whole or in part, documented in a technical construction file:

•EN 50081-2 EMC - Generic Emission Standard, Part 2 -

Industrial Environment

•EN 50082-2 EMC - Generic Immunity Standard, Part 2 -

Industrial Environment

This product is intended for use in an industrial environment.

Low Voltage Directive

This product is tested to meet Council Directive 73/23/EEC Low

Voltage, by applying the safety requirements of EN 61131-2

Programmable Controllers, Part 2 - Equipment Requirements and

Tests.

For specific information required by EN 61131-2, see the appropriate

sections in this publication, as well as the following Allen-Bradley

publications:

•Industrial Automation Wiring and Grounding Guidelines,

publication 1770-4.1

•Automation Systems Catalog, publication B111

Open style devices must be provided with environmental and safety

protection by proper mounting in enclosures designed for specific

application conditions. See NEMA Standards publication 250 and IEC

publication 529, as applicable, for explanations of the degrees of

protection provided by different types of enclosure.

ControlLogix DC (10-30V) Sourcing Input Module 5

Publication 1756-IN006A-EN-P - December 2000

Note the Power Requirements

This module receives power from the 1756 chasis power supply and

requires 2 sources of power from the backplane:

•110mA at 5.1V dc

•2mA at 24V dc

Add this current/power value (0.61W) to the requirements of all other

modules in the chassis to prevent overloading the power supply.

Install the Module

You can install or remove the module while chassis power is applied.

ATTENTION

The module is designed to support Removal and

Insertion Under Power (RIUP). However, when

you remove or insert an RTB with field-side power

applied, unintended machine motion or loss of

process control can occur. Exercise extreme

caution when using this feature.

20861–M 20862–M

1. Align circuit board with top and

bottom chassis guides. 2. Slide module into chassis until

module locking tabs ‘click’.

Printed

Circuit

Board

Lockingtab

Allen-Bradley Motors

6ControlLogix DC (10-30V) Sourcing Input Module

Publication 1756-IN006A-EN-P - December 2000

Key the Removable Terminal Block/Interface Module

Wedge-shaped keying tabs and U-shaped keying bands came with

your RTB to prevent connecting the wrong wires to your module.

Key positions on the module that correspond to unkeyed positions

on the RTB. For example, if you key the first position on the module,

leave the first position on the RTB unkeyed.

Reposition the tabs to rekey future module applications.

Wire the Removable Terminal Block

Wire the RTB with a 5/16 inch (8mm) maximum flat-bladed

screwdriver before installing it onto the module.

20850–M

1. Insert the U-shaped bandas shown.

2. Push the banduntil it snaps in place.

U-shaped

bands

1. Insert the wedge-shaped tab with rounded edge first.

2. Push thetab until it stops.

20851–M

Wedge-shaped tab

Key the Module Key the RTB/IFM

Spring Clamp RTB

1. Strip 7/16inch (11mm) maximum

length of wire.

2. Insert the screwdriver into the

inner hole of the RTB.

3. Insert thewire into the open terminal and

remove the screwdriver.

NEMA Screw RTB

1. Strip 5/16 inch (8mm) maximum length

of wire.

2. Turn the terminal screw counterclockwise.

3. Wrap wire around the terminal.

4. Turn the terminal screwclockwise.

ControlLogix DC (10-30V) Sourcing Input Module 7

Publication 1756-IN006A-EN-P - December 2000

Wire the Module

You can only connect wiring to your module through an RTB or IFM.

The example below shows how to wire the module.

After completing field-side wiring, secure the wires in the strain relief

area with a cable-tie.

1756-IV16

910

1314

1516

1718

1. Allterminalswiththesamenameareconnectedtogetheronthemodule.Forexample,DC

(+) can be connected to either terminal marked DC-1+. Ifyou are daisy chain wiring from

one ofthese terminals to other RTBs, only connect wiring to one terminal.

2. Whenyoudaisychainfroma grouptoanotherRTB,alwaysconnectthedaisychainto the

terminal directly connected to the supply wire, as shown above.

3. This wiring example showsa single voltage source.

4. If separate power sources are used,do not exceed thespecified isolation voltage.

–+

Daisy chain to other RTBs

Group 0Group 0

Group 1Group 1

DC COM

42552

IN-0

IN-2

IN-4

IN-6

DC-0 +

IN-8

IN-10

IN-12

IN-14

DC-1 +

IN-1

IN-3

IN-5

IN-7

DC-0 +

IN-9

IN-11

IN-13

IN-15

DC-1 +

NOTES:

Allen-Bradley Motors

8ControlLogix DC (10-30V) Sourcing Input Module

Publication 1756-IN006A-EN-P - December 2000

Assemble the Removable Terminal Block and the Housing

Install the Removable Terminal Block onto the Module

WARNING

The RTB is designed to support Removal and Insertion

Under Power (RIUP). However, when you remove or

insert an RTB with field-side power applied, unintended

machine motion or loss of process control can

occur. Exercise extreme caution when using this feature.

It is recommended that field-side power be removed

before installing the RTB onto the module.

When you remove or insert a module while field-side

power is applied, you may cause an electrical arc. An

electrical arc can cause personal injury or property

damage because it may:

•send an erroneous signal to your system’s field

devices, causing unintended machine motion or loss

of process control.

•cause an explosion in a hazardous environment.

Repeated electrical arcing causes excessive wear to

contacts on both the module and its mating connector.

Worn contacts may create electrical resistance.

When you insert or remove the module while backplane

power is on, or you connect or disconnect the RTB with

field-side power applied, an electrical arc can occur. This

could cause an explosion in hazardous location

installations. Be sure that power is removed or the area is

non-hazardous before proceeding.

20852-M

Groove

Side edge of the RTB

Strain relief area

1. Align the grooves at the bottom of the housing with the side edges ofthe RTB.

2. Slide the RTB intothe housing until it snaps into place.

ControlLogix DC (10-30V) Sourcing Input Module 9

Publication 1756-IN006A-EN-P - December 2000

Before installing the RTB, make certain:

•field-side wiring of the RTB has been completed.

•the RTB housing is snapped into place on the RTB.

•the RTB housing door is closed.

•the locking tab at the top of the module is unlocked.

20853–M

20854–M

Module

guide

RTB guides

Locking

tab

1. Alignthe side and top, bottom RTB guides with the

side, top and bottom module guides.

2. Press quickly and evenly toseat the RTB on the

module until the latches snap into place.

3. Slidethelockingtabdownto locktheRTB

onto the module.

Allen-Bradley Motors

10 ControlLogix DC (10-30V) Sourcing Input Module

Publication 1756-IN006A-EN-P - December 2000

Check the Indicators

The indicators show individual I/O status (yellow) for each point and

a bi-colored LED for module "OK" (red/green).

During power up, an indicator test is done and the following occurs:

•The "OK" indicator turns red for 1 second and then turns to

flashing green if it has passed the self-test.

•The I/O status indicators turn ON for a maximum of 2 seconds

and then turn OFF.

This completes installation of the module. Use the information below

to remove the module.

LED

indicator: This

display: Means: Take this action:

OK Steady

green light The inputs arebeing

multicast and in normal

operating state.

None

OK Flashing

green light The modulehas passed

internaldiagnosticsbutisnot

multicasting inputs.

Configure the module.

OK Flashing red

light Previously established

communication has timed out. Checkcontrollerandchassis

communication.

OK Steadyred

light An unrecoverable error has

occurredon the module. Replace themodule.

I/O State Yellow The input is active. None

20945-M

DC INPUT

ST01234567

ST 8 9 10 11 12 13 14 15 O

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley E/A-System Handbücher

Allen-Bradley

Allen-Bradley Micro800 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-IB Installations- und Benutzerhandbuch

Allen-Bradley

Allen-Bradley SLC 500 1746-NI4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-IB2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2097-TB1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-ECL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-ASB Bedienungsanleitung

Allen-Bradley

Allen-Bradley Flex integra 1793-IB16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NR4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-CM1771-LD005 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1397-L11 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-IB8S Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-OE2C Bedienungsanleitung

Allen-Bradley

Allen-Bradley Rockwell Automation 1734-AENT Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1791-32A0 Bedienungsanleitung

Allen-Bradley

Allen-Bradley CompactBlock LDX 1790D-T4T0 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-TBN Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IA8 Service-Handbuch

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA16I Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-HSC Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-IQ32 Service-Handbuch

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung