Allen-Bradley POINT I/O 1734-4IOL Bedienungsanleitung

Installation Instructions

POINT I/O 4 Channel IO-Link

Master Module

Catalog number 1734-4IOL

Table of Contents

Topic Page

Important User Information 2

Environment and Enclosure 3

Preventing Electrostatic Discharge 3

About the Module 5

Install the Mounting Base 7

Install the Module 8

Install the Removable Terminal Block 9

Wire the Module 11

Communicate with the Module 13

Interpret Status Indicators 15

Specifications 17

2POINT I/O 4 Channel IO-Link Master Module

Publication 1734-IN043A-EN-E - September 2015

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between

solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also

because of the wide variety of uses for solid-state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you

identify a hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

POINT I/O 4 Channel IO-Link Master Module 3

Publication 1734-IN043A-EN-E - September 2015

Environment and Enclosure

Preventing Electrostatic Discharge

ATTENTION: This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications (as defined in IEC

60664-1), at altitudes up to 2000 m (6562 ft) without derating. This equipment is

not intended for use in residential environments and may not provide adequate

protection to radio communication services in such environments.

This equipment is supplied as open-type equipment. It must be mounted within

an enclosure that is suitably designed for those specific environmental

conditions that will be present and appropriately designed to prevent personal

injury resulting from accessibility to live parts. The enclosure must have suitable

flame-retardant properties to prevent or minimize the spread of flame,

complying with a flame spread rating of 5VA or be approved for the application

if nonmetallic. The interior of the enclosure must be accessible only by the use

of a tool. Subsequent sections of this publication may contain additional

information regarding specific enclosure type ratings that are required to

comply with certain product safety certifications.

In addition to this publication, see:

• Industrial Automation Wiring and Grounding Guidelines, Rockwell

Automation publication 1770-4.1, for additional install requirements.

• NEMA Standard 250 and IEC 60529, as applicable, for explanations of the

degrees of protection provided by enclosures.

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

4POINT I/O 4 Channel IO-Link Master Module

Publication 1734-IN043A-EN-E - September 2015

ATTENTION: This product is grounded through the DIN rail to chassis ground.

Use zinc plated yellow-chromate steel DIN rail to assure proper grounding. The

use of other DIN rail materials (for example, aluminum or plastic) that can

corrode, oxidize, or are poor conductors, can result in improper or intermittent

grounding. Secure DIN rail to mounting surface approximately every 200 mm

(7.8 in.) and use end-anchors appropriately.

ATTENTION: Do not remove or replace an Adapter Module while power is

applied. Interruption of the backplane can result in unintentional operation or

machine motion.

ATTENTION: To comply with UL restrictions, this equipment and all connected

I/O must be powered from a source compliant with the following:

Safety Extra Low Voltage (SELV)

ATTENTION: To comply with CE Low Voltage Directive (LVD), this equipment

and all connected I/O must be powered from a source compliant with the

following:

Safety Extra Low Voltage (SELV)

ATTENTION: Do not wire more than 2 conductors on any single terminal.

POINT I/O 4 Channel IO-Link Master Module 5

Publication 1734-IN043A-EN-E - September 2015

About the Module

The POINT I/O 4 Channel IO-Link Master Module provides four channels that can be

individually configured as IO-Link master or as a standard digital I/O module. The

IO-Link channel master module can be configured to fit any IO-Link and/or discrete

application.

In IO-Link mode, the module supports four channels for IO-Link master communication

with IO-Link compatible devices. In standard digital I/O mode, the module supports four

channels of digital input or output. Standard digital input channels support IEC61131-2

type 1 input. Channels can also be disabled if not in use.

You must use this module with the 1734-AENT or 1734-AENTR, Series B EtherNet/IP

adapters, firmware version 5.012 or later, and RSLogix™ 5000/Studio 5000® software,

version 20 or later. Use this diagram to identify the external features of the module.

POINT I/O 4 Channel IO-Link Master Module with 1734-TB, 1734-TBS,

1734-TB3, or 1734-TB3S Wiring Base Assembly

Analog

Voltage

Output

Module

Status

Network

Status

NODE:

24V DC

SIO

LINK

Module

Status

Network

Status

1734-4IOL

NODE:

The 1734-TB, 1734-TBS, 1734-TB3, or

1734-TB3S wiring base assembly

consists of a 1734-MB mounting base

and a 1734-RTB or 1734-RTBS removable

terminal block.

46012

6POINT I/O 4 Channel IO-Link Master Module

Publication 1734-IN043A-EN-E - September 2015

POINT I/O 4 Channel IO-Link Master Module with 1734-TOP, 1734-TOPS,

1734-TOP3, or 1734-TOP3S One-Piece Terminal Base

Description Description

1 Module locking mechanism 6 Terminal base

2 Slide-in writable label 7 Interlocking side pieces

3 Insertable I/O module 8 Mechanical keying (orange)

4 Removable terminal block (RTB) handle 9 DIN rail locking screw (orange)

5 Removable terminal block 10 Module wiring diagram

Description Description

1 Module locking mechanism 6 Interlocking side pieces

2 Slide-in writable label 7 Mechanical keying (orange)

3 Insertable I/O module 8 DIN rail locking screw (orange)

4 Terminal block handle 9 Module wiring diagram

5 One-piece terminal base

24V DC

SIO

LINK

Module

Status

Network

Status

1734-4IOL

NODE:

46013

POINT I/O 4 Channel IO-Link Master Module 7

Publication 1734-IN043A-EN-E - September 2015

Install the Mounting Base

To install the mounting base on the DIN rail, proceed as follows:

1. Position the mounting base vertically above the installed units (adapter, power

supply or existing module).

2. Slide the mounting base down allowing the interlocking side pieces to engage the

adjacent module or adapter.

3. Press firmly to seat the mounting base on the DIN rail. The mounting base snaps

into place. Be sure that the orange DIN rail locking screw is in the horizontal

position and that it has engaged the DIN rail.

ATTENTION: Do not discard the end cap. Use this end cap to cover the exposed

interconnections on the last mounting base on the DIN rail. Failure to do so

could result in equipment damage or injury from electric shock.

Slide the mounting base until the

interlocking side pieces engage the

adjacent module or adapter.

46014

8POINT I/O 4 Channel IO-Link Master Module

Publication 1734-IN043A-EN-E - September 2015

Install the Module

The module can be installed before or after base installation. Make sure that the mounting

base is correctly keyed before installing the module into the mounting base. In addition,

make sure the mounting base locking screw is positioned horizontal referenced to the base.

1. Using a bladed screwdriver, rotate the keyswitch on the mounting base clockwise

until the number required for the type of module being installed aligns with the

notch in the base.

2. Make certain the DIN rail locking screw is in the horizontal position. You cannot

insert the module if the locking mechanism is unlocked.

3. Insert the module straight down into the mounting base.

Turn the keyswitch to

align the number with

the notch. Notch

position 2 is shown.

Be sure the DIN-rail

locking screw is in the

horizontal position.

1734-TB Base

44229

Turn the keyswitch

to align the number

with the notch.

Notch position 2 is

shown.

Be sure the DIN-rail

locking screw is in the

horizontal position.

1734-TOP Base

44228

POINT I/O 4 Channel IO-Link Master Module 9

Publication 1734-IN043A-EN-E - September 2015

4. Press to secure. The module locks into place.

Install the Removable Terminal Block

A removable terminal block (RTB) is supplied with your wiring base assembly. To remove,

pull up on the RTB handle. This allows the mounting base to be removed and replaced as

necessary without removing any of the wiring. To reinsert the removable terminal block,

proceed as follows:

1. Insert the end opposite the handle into the base unit. This end has a curved

section that engages with the wiring base.

2. Rotate the terminal block into the wiring base until it locks itself in place.

24VDC

Source

Output

Module

Status

Network

Status

1734

OB4E

NODE:

24V DC

SIO

LINK

Module

Status

Network

Status

1734-4IOL

NODE:

44013

10 POINT I/O 4 Channel IO-Link Master Module

Publication 1734-IN043A-EN-E - September 2015

3. If an I/O module is installed, snap the RTB handle into place on the module.

Remove a Mounting Base

To remove a mounting base, you must remove any installed module and the module

installed in the base to the right. Remove the removable terminal block, if wired.

1. Unlatch the RTB handle on the I/O module.

2. Pull on the RTB handle to remove the removable terminal block.

3. Press on the module lock on the top of the module.

4. Pull on the I/O module to remove from the base.

5. Repeat steps 1, 2, 3 and 4 for the module to the right.

6. Use a small bladed screwdriver to rotate the orange base locking screw to a vertical

position. This releases the locking mechanism.

7. Lift straight up to remove.

24V DC

SIO

LINK

Module

Status

Network

Status

1734-4IOL

NODE:

Insert the module straight

down into the mounting base.

Hook the RTB end into

the mounting base

end and rotate until it

locks into place.

44012

Andere Handbücher für POINT I/O 1734-4IOL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley E/A-System Handbücher

Allen-Bradley

Allen-Bradley 1719 Ex I/O Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-IB2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1797-IBN16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746-IA4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock LP2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-HSC Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746-INT4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA16I Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock-LP 1792-IB16LP Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock MaXum 1792D-8BVT8D Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-OE4C Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-IB4D Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-OE2C Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IB16D Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-ECL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IM8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IG16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NR4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IF6CIS Bedienungsanleitung

Allen-Bradley

Allen-Bradley CompactBlock LDX 1790D-T4T0 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 ControlLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IG16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IT8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung