Allen-Bradley 1734-OE4C Bedienungsanleitung

Installation Instructions

POINT I/O 4 Channel Analog Current

Output Module

Catalog numbers 1734-OE4C

Table of Contents

Topic Page

Important User Information 2

Environment and Enclosure 3

Preventing Electrostatic Discharge 3

North American Hazardous Location Approval 4

European Hazardous Location Approval 5

Before You Begin 6

Install the Mounting Base 8

Install the Module 9

Install the Removable Terminal Block 11

Remove a Mounting Base 13

Wire the Module 14

Communicate with Your Module 15

Interpret Status Indicators 16

Specifications 17

2POINT I/O 4 Channel Analog Current Output Module

Publication 1734-IN034C-EN-E - August 2016

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between

solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also

because of the wide variety of uses for solid-state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you

identify a hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that surfaces may reach dangerous temperatures.

IMPORTANT

Identifies information that is critical for successful application and understanding of

the product.

POINT I/O 4 Channel Analog Current Output Module 3

Publication 1734-IN034C-EN-E - August 2016

Environment and Enclosure

Preventing Electrostatic Discharge

ATTENTION: This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications (as defined in IEC

60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according

to IEC/CISPR 11. Without appropriate precautions, there may be difficulties

with electromagnetic compatibility in residential and other environments due to

conducted and radiated disturbances.

This equipment is supplied as open-type equipment. It must be mounted within

an enclosure that is suitably designed for those specific environmental

conditions that will be present and appropriately designed to prevent personal

injury resulting from accessibility to live parts. The enclosure must have

suitable flame-retardant properties to prevent or minimize the spread of flame,

complying with a flame spread rating of 5VA, V2, V1, V0 (or equivalent) if

non-metallic. The interior of the enclosure must be accessible only by the use of

a tool. Subsequent sections of this publication may contain additional

information regarding specific enclosure type ratings that are required to

comply with certain product safety certifications.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines, for additional

installation requirements, Allen-Bradley publication 1770-4.1.

• NEMA Standards publication 250 and IEC publication 60529, as applicable,

for explanations of the degrees of protection provided by different types of

enclosure.

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wrist strap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

4POINT I/O 4 Channel Analog Current Output Module

Publication 1734-IN034C-EN-E - August 2016

North American Hazardous Location Approval

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l’utilisation de cet équipement

en environnements dangereux:

Products marked “CL I, DIV 2, GP A, B, C, D” are

suitable for use in Class I Division 2 Groups A, B, C,

D, Hazardous Locations and nonhazardous locations

only. Each product is supplied with markings on the

rating nameplate indicating the hazardous location

temperature code. When combining products within

a system, the most adverse temperature code

(lowest “T” number) may be used to help determine

the overall temperature code of the system.

Combinations of equipment in your system are

subject to investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués “CL I, DIV 2, GP A, B, C, D” ne

conviennent qu'à une utilisation en environnements de

Classe I Division 2 Groupes A, B, C, D dangereux et non

dangereux. Chaque produit est livré avec des marquages

sur sa plaque d'identification qui indiquent le code de

température pour les environnements dangereux. Lorsque

plusieurs produits sont combinés dans un système, le code

de température le plus défavorable (code de température le

plus faible) peut être utilisé pour déterminer le code de

température global du système. Les combinaisons

d'équipements dans le système sont sujettes à inspection

par les autorités locales qualifiées au moment de

l'installation.

EXPLOSION HAZARD

• Do not disconnect equipment unless

power has been removed or the area

is known to be nonhazardous.

• Do not disconnect connections to

this equipment unless power has

been removed or the area is known

to be nonhazardous. Secure any

external connections that mate to

this equipment by using screws,

sliding latches, threaded connectors,

or other means provided with this

product.

• Substitution of components may

impair suitability for Class I, Division

• If this product contains batteries,

they must only be changed in an

area known to be nonhazardous.

RISQUE D’EXPLOSION

• Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher

l'équipement.

• Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher les

connecteurs. Fixer tous les connecteurs

externes reliés à cet équipement à l'aide

de vis, loquets coulissants, connecteurs

filetés ou autres moyens fournis avec ce

produit.

• La substitution de composants peut

rendre cet équipement inadapté à une

utilisation en environnement de Classe I,

Division 2.

• S'assurer que l'environnement est classé

non dangereux avant de changer les

piles.

ATTENTION: To comply with UL restrictions, field power and all connected

devices must be powered from a single source compliant with the following:

Class 2

ATTENTION: To comply with the CE Low Voltage Directive (LVD), field power

and all connected I/O must be powered from a source compliant with the

following:

Safety Extra Low Voltage (SELV) or Protected Extra Low Voltage (PELV).

POINT I/O 4 Channel Analog Current Output Module 5

Publication 1734-IN034C-EN-E - August 2016

European Hazardous Location Approval

The following applies when the product bears the Ex Marking

This equipment is intended for use in potentially explosive atmospheres as defined by European Union

Directive 94/9/EC.

DEMKO certifies that this equipment has been found to comply with the Essential Health and Safety

Requirements relating to the design and construction of Category 3 equipment intended for use in Zone

2 potentially explosive atmospheres, given in Annex II to this Directive.

Compliance with the Essential Health and Safety Requirements has been assured by compliance with

EN 60079-0:2012+A11:2013, EN 60079-15:2010, reference certificate number DEMKO

04ATEX0330347X.

WARNING: This equipment shall be mounted in an ATEX certified enclosure

with a minimum ingress protection rating of at least IP54 (as defined in

IEC60529) and used in an environment of not more than Pollution Degree 2 (as

defined in IEC 60664-1) when applied in Zone 2 environments. The enclosure

must utilize a tool removable cover or door.

WARNING: This equipment shall be used within its specified ratings defined

by Rockwell Automation.

WARNING: Provision shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 140% of the rated voltage

when applied in Zone 2 environments.

WARNING: This equipment must be used only with ATEX certified Rockwell

Automation backplanes.

WARNING: Secure any external connections that mate to this equipment by

using screws, sliding latches, threaded connectors, or other means provided

with this product.

WARNING: Do not disconnect equipment unless power has been removed or

the area is known to be nonhazardous.

ATTENTION: If this equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be impaired.

ATTENTION: This equipment is not resistant to sunlight or other sources of

UV radiation.

6POINT I/O 4 Channel Analog Current Output Module

Publication 1734-IN034C-EN-E - August 2016

Before You Begin

Note that this series C product can be used with the following:

• DeviceNet and PROFIBUS adapters

• ControlNet and EtherNet/IP adapters, using RSLogix 5000 software, version 11

or later

See the figures to familiarize yourself with major parts of the module, noting that the

wiring base assembly is one of the following:

• 1734-TB or 1734-TBS POINT I/O two-piece terminal base, which includes the

1734-RTB removable terminal block and 1734-MB mounting base

• 1734-TOP or 1734-TOPS POINT I/O one-piece terminal base

POINT I/O 4 Channel Analog Current Output Module

Module

Status

Network

Status

NODE:

44328

POINT I/O 4 Channel Analog Current Output Module 7

Publication 1734-IN034C-EN-E - August 2016

Description Description

1 Module locking mechanism 6 Mounting base – 1734-TB, 1734-TBS

2 Slide-in writable label 7 Interlocking side pieces

3 Insertable I/O module 8 Mechanical keying (orange)

4 Removable Terminal Block (RTB) handle 9 DIN rail locking screw (orange)

5 RTB with screw or spring clamp 10 Module wiring diagram

Description Description

1 Module locking mechanism 6 Interlocking side pieces

2 Slide-in writable label 7 Mechanical keying (orange)

3 Insertable I/O module 8 DIN rail locking screw (orange)

4 Handle 9 Module wiring diagram

5 One-piece terminal base with screw or

spring clamp – 1734-TOP, 1734-TOPS

44221

8POINT I/O 4 Channel Analog Current Output Module

Publication 1734-IN034C-EN-E - August 2016

Install the Mounting Base

To install the mounting base on the DIN rail (Allen-Bradley part number 199-DR1;

46277-3; EN50022), proceed as follows:

1. Position the mounting base vertically above the installed units (adapter, power

supply or existing module).

2. Slide the mounting base down allowing the interlocking side pieces to engage the

adjacent module or adapter.

3. Press firmly to seat the mounting base on the DIN rail. The mounting base snaps

into place.

4. To remove the mounting base from the DIN rail, remove the module, and use a

small bladed screwdriver to rotate the base locking screw to a vertical position.

This releases the locking mechanism. Then lift straight up to remove.

ATTENTION: This product is grounded through the DIN rail to chassis

ground. Use zinc plated, yellow-chromate steel DIN rail to be sure of proper

grounding. The use of other DIN rail materials, such as aluminum and plastic,

which can corrode, oxidize, or are poor conductors, can result in improper or

intermittent grounding. Secure DIN rail to mounting surface approximately

every 200 mm (7.87 in.) and use end-anchors appropriately.

31586

POINT I/O 4 Channel Analog Current Output Module 9

Publication 1734-IN034C-EN-E - August 2016

Install the Module

The module can be installed before or after base installation. Make sure that the mounting

base is correctly keyed before installing the module into the mounting base. In addition,

make sure the mounting base locking screw is positioned horizontal referenced to the base.

1734-TB Base

WARNING: When you insert or remove the module while backplane power

is on, an electrical arc can occur. This could cause an explosion in hazardous

location installations.

Be sure that power is removed or the area is nonhazardous before

proceeding. Repeated electrical arcing causes excessive wear to contacts on

both the module and its mating connector. Worn contacts may create

electrical resistance that can affect module operation.

Turn the keyswitch to align the

number with the notch.

Notch position 4 is shown.

Make sure the DIN rail locking

screw is in the horizontal position.

44229

10 POINT I/O 4 Channel Analog Current Output Module

Publication 1734-IN034C-EN-E - August 2016

1734-TOP Base

1. Using a bladed screwdriver to rotate the keyswitch on the mounting base

clockwise until the number required for the type of module being installed aligns

with the notch in the base.

2. Make certain the DIN rail locking screw is in the horizontal position.

You cannot insert the module if the locking mechanism is unlocked.

3. Insert the module straight down into the mounting base and press to secure.

The module locks into place.

Turn the keyswitch to align the

number with the notch.

Notch position 4 is shown.

Make sure the DIN-rail locking

screw is in the horizontal position.

44228

Inhaltsverzeichnis

Andere Allen-Bradley E/A-System Handbücher

Allen-Bradley

Allen-Bradley FLEX I/O 1794-TBN Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IG16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IB16D Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock MaXum 4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2097-TB1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Flex I/O Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-ASB Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-CM1771-LD005 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IE12 Bedienungs- und Wartungshandbuch

Allen-Bradley

Allen-Bradley Micro800 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NR4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NT8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IB10XOB6 Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-IE2C Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-HSC Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IQ32T Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NI4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-4IOL Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung