Allen + Roth F121E413CP Bedienungsanleitung

ATTACH YOUR RECEIPT HERE

Serial Number ____________________________ Purchase Date _________________________

SM20277

Français p. 19

ITEM #80375170

#80375171

#2564457

#2564458

SINGLE-HANDLE

TUB & SHOWER FAUCET

MODEL #F121E413CP

#F121E413BL

Questions, problems, missing parts? Before returning to your retailer, call our

customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

ALLEN + ROTH and logo design are trademarks or

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

A Shower head 1

B Shower arm 1

CShower arm ange 1

D Handle 1

E Escutcheon 1

F Escutcheon seal 1

G Plaster guard 1

H Valve body 1

I Spout 1

J Plug 1

K Screen washer 1

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the

product.

NOISE AND WATER HAMMER IN PEX SYSTEMS

As with all plumbing materials under some operating conditions, water hammer can occur in PEX

plumbing systems. The inherent flexibility of PEX drastically reduces the magnitude of pressure

surges compared with metallic plumbing materials. Damage to plumbing components in a PEX

system due to these pressure surges in highly unlikely, although noise can sometimes result.

Fortunately, there are solutions to minimize of eliminate water hammer noise.

Clamping or strapping more frequently may help prevent tubing noise. It is very important that the

tubing not be in contact with wall-board, forced air ducts or other high resonance articles. Insufficiently

or improperly clamped or strapped tubing may move during fixture operation and hit against these

surfaces.

Install a water hammer arrester at fixtures where noise is a problem. A water hammer arrester

installed within 6 feet of the fixture on the cold water side only will eliminate the source of the noise:

the pressure wave. It should be noted that even with an arrester, tubing which is clamped or strapped

insufficiently may still hit against something as it moves slightly when the water flow is stopped.

Avoid operating fixtures in such a way that causes near instantaneous shut off. Simply closing fixtures

in a less abrupt manner can eliminate hammer noise.

CAUTION:

Inlet ports are designed to allow for 1/2 in. copper tubing solder connection or 1/2 in. IPS threading

coupling connection. For threaded connections, wrap pipe tape around threaded ends before

connecting. If soldering connections, remove plaster guard, cartridge and check valves. Connect

water supply to the pipe by soldering. Reassemble check valves, cartridge and plaster guard.

Heat damage to these parts may occur and result in the warranty being void on these parts.

Long Screw

Thread TapeHex Wrench Wrench

AA CCBB DD

SAFETY INFORMATION

WARNING

• This product is engineered to meet the EPA WaterSense flow requirement. The flow rate is

governed by the aerator or flow controller. If replacement is ever required, be sure to replace it with

a WaterSense compliant aerator or flow controller to retain the water conserving flow rate of this

product.

• The automatic compensating valve shall be used with shower rated at 1.3 gpm (4.9 L/min) or higher.

• The shower shall be used with automatic compensating valve rated at 1.43 gpm (5.4 L/min) or less.

• The product should be installed by a locally licensed plumber.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and hardware contents list. If any part is missing or damaged, do not attempt to

assemble the product.

Estimated Assembly Time: 40 minutes

Tools Required for Assembly (not included): Adjustable Wrench, Screwdriver, Safety Googles.

Helpful Tools (not included): Supply stops, Supply tubing/ttings, Basin wrench.

• Prior to beginning installation, turn off the cold and hot water lines and turn on the old faucet to

release built-up pressure.

• When installing your new faucet, rst hand-tighten connector nuts. Connections that are too tight will

reduce the integrity of the system.

If you are replacing your plumbing valve, please review the four common plumbing methods

illustrated below: CPVC, PEX, IPS, and Copper. Remove the existing handle and valve trim before

replacing your valve. Please follow all local building and plumbing codes.

A.CPVC-1

A.CPVC-2

CPVC Cement Tubing Cutter SharkBite Fittings CPVC Cleaner

A. CPVC

Use 1/2” Copper or

IPS Pipe Only

Use 1/2” Copper or

IPS Pipe Only

CPVC Cement

SharkBite Fittings

Tubing Cutter

CPVC Cleaner

B. PEX-1

C. IPS-1

B. PEX-2

C. IPS-1

B. PEX

C. IPS

Use 1/2” Copper or

IPS Pipe Only

Use 1/2” Copper or

IPS Pipe Only

SharkBite Fittings

Tube Cutter

Tubing Cutter Full Circle Crimping Tool

SharkBite Fittings

Full Circle Crimping Tool

Tubing Cutter

Tube Cutter

1. Shut off main water supply before installation.

ASSEMBLY INSTRUCTIONS

D. COPPER

Torch Tube Cutter Wire Brush Lead-free Solder Kit SharkBite Fittings

D. COPPER-1

Torch

Wire Brush

Lead-free Solder Kit

Tube Cutter

SharkBite Fittings

2. Note the installation distance between shower

arm (B), handle (D), and spout (I).

3a. Thin Wall Installation:

Use this method for when shower walls are

thinner than 1/4 inch, such as fiberglass tub

surrounds, and will be the main source of

support for the valve. The plaster guard remains

attached to the valve. See figure at right.

ASSEMBLY INSTRUCTIONS

3b. Thick Wall Installation:

Use this method when the shower wall is greater

than 1/4 inches thick. “Thick walls” are usually

built up with materials such as cement board,

drywall, tile, etc. The valve is secured by straps

(not included) holding the water inlet lines to the

framing members (2x4’s). The plaster guard is

positioned so that it is flush with the finished wall.

This ensures that the valve will be at the correct

position to accept the trim.

48 in. (1.22m)

Tub & Shower

30 in. (76.2cm)

Shower Only

48 in. (1.22m)

Shower Only

8 in. (20.3cm) min.

30 in. (76.2cm)

Tub & Shower

Less than 1/4”

(6mm)

More than 1/4”

(6mm)

3/4”

(19mm)

2-1/4” min.

(57mm)

3-1/2” max.

(89mm)

5-1/2”

(140 mm)

ASSEMBLY INSTRUCTIONS

4. The plaster guard (G) is adjustable to

accommodate the installation needs.

5a. For pipe 4: Use 1/2 in. copper or IPS pipe only.

If soldering connections, cartridge and integral

stops must be removed to avoid heat damage.

Reinstall when connections are completed and

valve has cooled.

5b. Note: Includes a valve plug (J) so fixture can

be used in Shower Only applications.

5-3/16”

(131mm)

3-1/16 in.

(77.7mm)

2-13/16”

(71mm)

OPTION

6. Install stub-out pipe (not included) for spout.

Use proper length stub-out pipe so pipe

threads will extend 1-1/2 to 2 inches beyond

finished wall.

7b. Threaded installation: Apply thread tape on

the pipe nipple threads. Remove the adapter

assembly (including plastic adapter, plastic

washer, O-Ring), back out the set screw. Slide

spout (I) over the pipe with the spout tight to the

wall, tighten the set screw.

ASSEMBLY INSTRUCTIONS

7a. Slipped installation: Install tub spout (I).

Tighten set screw using hex wrench.

1 1/2 ~ 2 in

1/2-14NPT

all

10. Remove plastic cap on plaster guard (G) by

twisting clockwise.

ASSEMBLY INSTRUCTIONS

9. Install shower head (A) to shower arm (B).

Hand tighten shower head.

8. Install shower arm (B) and shower arm ange (C)

to vertical shower pipe elbow. 8

all

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Allen + Roth Sanitärprodukte Handbücher

Allen + Roth

Allen + Roth CAMERON 60MB Bedienungsanleitung

Allen + Roth

Allen + Roth 67130W-602707 Bedienungsanleitung

Allen + Roth

Allen + Roth 67124W-6104 Bedienungsanleitung

Allen + Roth

Allen + Roth LWSJ48VBR Bedienungsanleitung

Allen + Roth

Allen + Roth 67095W-6204 Bedienungsanleitung

Allen + Roth

Allen + Roth FS1A9281CP Bedienungsanleitung

Allen + Roth

Allen + Roth 67131W-602707 Bedienungsanleitung

Allen + Roth

Allen + Roth LWSG30VBR Bedienungsanleitung

Allen + Roth

Allen + Roth 2889548 Bedienungsanleitung

Allen + Roth

Allen + Roth FW6AC035CP Bedienungsanleitung

Allen + Roth

Allen + Roth ML-20518 Bedienungsanleitung

Allen + Roth

Allen + Roth 67123W-622707 Bedienungsanleitung

Allen + Roth

Allen + Roth WSWS-PB1C Bedienungsanleitung

Allen + Roth

Allen + Roth 21-B45WDCP-AR Bedienungsanleitung

Allen + Roth

Allen + Roth ML-20503R Bedienungsanleitung

Allen + Roth

Allen + Roth LWSJ60VBR Bedienungsanleitung

Allen + Roth

Allen + Roth FELIX 24WG Bedienungsanleitung

Allen + Roth

Allen + Roth ELIZA 71-BVF11-BN-AR Bedienungsanleitung

Allen + Roth

Allen + Roth 67692W-6104 Bedienungsanleitung

Allen + Roth

Allen + Roth 58101-X607011 Bedienungsanleitung

Allen + Roth

Allen + Roth ML-20522 Bedienungsanleitung

Allen + Roth

Allen + Roth ML-20602R Bedienungsanleitung

Allen + Roth

Allen + Roth CAMERON 42MB Bedienungsanleitung

Allen + Roth

Allen + Roth CAMERON 36MB Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema